Lube Adhesive & Engineering Co.

Ahmedabad, Gujarat

GST No. 24AQYPM1863D1ZL

Call 08048964000 73% Response Rate

Send Enquiry

Bearing Retainer

We are a leading Wholesale Supplier of anr 122 bearing retainer adhesive, anabond 402 bearing retainer adhesives, fasto a338 retaining adhesive, fasto a339 retaining adhesive, fasto a341 retaining adhesive and fasto a360 retaining adhesive from Ahmedabad, India.

ANR 122 Bearing Retainer Adhesive

Rs 130 / PieceGet Best Price

Minimum Order Quantity: 30 Piece

Color	Red
Viscosity	150-275
Static Shear Strength	19 N/MM2
Gap Fill MM	0.10
Fixture time	10 Min
Full Cure	24 Hrs
Temperature Resistance	-50 to 150 degree C
Applications	Close fitting parts, retaining of rotor to shafts in fractional and sub fractional horsepower motors

We are successfully meeting the varied needs of our patrons by offering a wide gamut of ANR 122 Bearing Retainer Adhesive as per their precise needs.

View Complete details

get quote request a call back

Anabond 402 Bearing Retainer Adhesives

Rs 130 / NumberGet Best Price

Minimum Order Quantity: 20 Number

Product Brochure

Brand	ANABOND
Color	RED
Material	ANEROBIC
Usage	Industrial
Shear Strength	HIGH
Cure Time	24 HOURS
Technology	ANAEROBIC
Service Temperature	-60 TO 200
Feature	RETAINING FOR BEARING,SHAFT
Packaging Type	BOTTLE
Usage/Application	Typical applications include locking bushing & sleeves into housing & shaft
Weight	225-300 kg.cm2
Common Application	locking bushing,houseing,shaft
Chemical Composition	Dimethacrylate ester
Cure Method	handing cure 8 to 12,functional cure 3,full cure 24
Fixture Time	24 hour
Flash Point	rrefer msds
Gap Fill Mm	0.25 mm
Strength Required	High

Anabond*ATM – Anabond Test Method, ISO – International Organization for Standardization, JISProduct DescriptionAnabond 402 is a single component dimethacrylateester based fast curing high strength anaerobicadhesive system specially designed for permanentbonding and sealing of cylindrical fitting partsmaximum strength is required. The product getspolymerized when confined between closely matingmetal surfaces in the absence of air and preventsloosening and leakage from shock and vibration.product exhibits good temperature performance,chemical resistance and lubricating property.applications include locking bushings and sleeves intohousings and on shafts.Properties of uncured materialCuring performanceThe product cures when confined in the absence of airbetween closed fitting metal surfaces. The curing timeis influenced by the gap between the surfaces, the kindof metal, surface treatments and temperature.assembly can be subjected to limitedfunctional cure. Although functional cure is developed ina relatively short time, curing continues for at least 24hours before full properties are developed.tested according to ATM*-R031 (ISO 10964)R025 (ISO 10123)..Specific Gravity at 30°C,ATM-R004 *(JIS K6820)1.0Viscosity at 30°C, Brookfield DVII+,Spindle 5, speed 100 rpm, cP,ATM-R006 *(ISO 2555)1800Flash point refer MSDSChemical Type Dimethacrylate esterAppearance High viscous liquidCure AnaerobicApplication RetainingStrength HighColour RedAnabond®402– Japanese Industrial Standardparts, whereTheicating TypicalThetest afterCuring& ATMOperatingParametersProperties of cured materialCured for 24 hours at 30±2 °C, tested according toATM-R025 (ISO 10123).Typical Environmental ResistanceCured for 7days at 30±2 °C,steel pins and collars according to10123).Hot StrengthTested at temperature indicatedHeat AgingAged at temperature indicated and tested atChemical resistanceAged under conditions indicated and tested atAging time (hrs)% of initial strengthAged at 120100 100500 1001000 100Test TemperatureAt 500CAt 1000CAt 1500CCompressive shear strength,Steel pin and collarsRecommended gap,ATM R025 (ISO 10123)Service temperatureATM -R025 (ISO 10123)Handling cure at 30 ± 2 °C, minFunctional cure at 30 ± 2 °C, hFull cure at 30 ± 2 °C, h– 1.1- 2000Technical Data SheetRevised: Feb 15Revision no.:01Page 1 of 3±±Shear strength tested onATM-R025 (ISO30 ± 2°C.30 ± 2°C.0C Aged at 1500C1009898% of initial strength1008060, N/mm2(kg/cm2)22.5 – 30(225-300)mm 0.25⁰C -60 to +2008 - 12324Anabond*ATM – Anabond Test Method, ISO – International Organization for Standardization, JISGeneral informationBefore handling read product safety data sheet andcontainer label for safe use.This product is not recommended for use in pureoxygen or oxygen rich systems and not be selected asa sealant for chlorine or other strong oxidizing materialsTo prevent the product from clogging in the nozzle, donot allow the tip to touch the metal surfaces duringapplication.Do not return the used product back to the originalcontainer as it may be contaminated during usage.Where aqueous washing systems are used to clean thesurfaces before bonding, it is important to check thecompatibility of the washing solution with the adhesive.In some cases these aqueous washes can affect thecure and performance of the adhesiveThe product is not normally recommended for use onplastics, particularly thermoplastic materials wherestress cracking of plastic could result. Users arerecommended to check the compatibility of the productwith such substrates.Directions for useSubstrate preparationAll surfaces must be clean and dryFor best results degrease the surfacesolvent and allow it to dry before applying the adhesive.If the metal surface is inactive or curing speed is slowuse activator, Anabond Ekaprime 021.Method of applicationChemicals

Additional Information:

Delivery Time: within 2 days
Packaging Details: 50 Ml & 250 Ml Pack

View Complete details

get quote request a call back

Fasto A338 Retaining Adhesive

Rs 349 / PieceGet Best Price

Form	Liquid
Material Compatibility	Ceramic
Adhesion Properties	Pressure Sensitive
Brand	Fasto
Chemical Composition	Silicone
Origin	Synthetic
Packaging Size	50 ml also available in 250 ml

By leveraging upon our huge industry experience, we provide the best quality array of Fasto A338 Retaining Adhesive.

Other detail:

Fasto A338 is high strength, high viscosity and fast curing retaining compound for bonding cylindrical assemblies with clearance.
Typical applications include retaining of locking sleeves, bearings, pulleys, sprockets, gears onto shafts.

Price:

Pack size	Price	Gst Extra
250 ml	1622	18%

Additional Information:

Item Code: Fasto-A338

View Complete details

get quote request a call back

Fasto A339 Retaining Adhesive

Rs 349 / PieceGet Best Price

Form	Liquid
Material Compatibility	Composites
Adhesion Properties	Pressure Sensitive
Brand	Fasto
Chemical Composition	Silicone
Origin	Synthetic
Packaging Size	50 ml also available in 250 ml

Relying on our expertise in this domain, we are engaged in offering Fasto A339 Retaining Adhesive to our respected clients.

Price:

Pack size	Price	Gst Extra
250 ml	1622	18%

Additional Information:

Item Code: Fasto-A339

View Complete details

get quote request a call back

Fasto A341 Retaining Adhesive

Rs 349 / PieceGet Best Price

Form	Liquid
Material Compatibility	Ceramic
Adhesion Properties	Pressure Sensitive
Chemical Composition	Silicone
Brand	Fasto
Origin	Synthetic
Packaging Size	50 ml also available in 250 ml

We have gained a huge appreciation in the market by offering an excellent array of Fasto A341 Retaining Adhesive.

Details:

Fasto A341 is a single component, anaerobic retaining compound formulated to give a controlled medium strength bond.
Typical applications include mounting bearing in place on shafts and in housings.
The controlled medium strength allows disassembly for servicing and bearing re-use.
A341 prevents corrosion of assembling parts.

Features:

Provide perfect seal
Low viscosity
Excellent sticking property

Price:

Pack size	Price	Gst Extra
250 ml	1622	18%

Additional Information:

Item Code: Fasto-A341

View Complete details

get quote request a call back

Fasto A360 Retaining Adhesive

Rs 569 / PieceGet Best Price

Form	Liquid
Material Compatibility	Plastic
Adhesion Properties	Pressure Sensitive
Brand	Fasto
Chemical Composition	Silicone
Origin	Synthetic
Packaging Size	50 ml also available in 250 ml

Features:

High strength
Large gap fill
Strong adhesiveness
High shear strength
Easy to apply

Price:

Pack size	Price	Gst Extra
250 ml	2704	18%

Additional Information:

Item Code: Fasto-A360

View Complete details

get quote request a call back

Fasto A320 Retaining Adhesive

Rs 605 / PieceGet Best Price

Material Compatibility	Ceramic
Packaging Size	50 ml also available in 250 ml
Chemical Composition	Silicone
Adhesion Properties	Pressure Sensitive
Origin	Synthetic
Brand	Fasto
Form	Liquid

Owing to the years of industrial experience, we have been able to provide our valued clients with a wide range of Fasto A320 Retaining Adhesive.

Other detail:

Fasto A320 is suitable for high strength and high temperature retaining compound.
It applications that require large gap filling.
Fasto A320 is designed to augment the strength of slip fit assemblies and for use on loose-fitting or worn parts, where larger gap fill is required.

Price:

Pack size	Price	Gst Extra
250 ml	2283	18%

Additional Information:

Item Code: Fasto-A320

View Complete details

get quote request a call back

ANABOND BEARING RETAINER

Rs 35 / NumberGet Best Price

Minimum Order Quantity: 12 Number

Product Brochure

Brand	ANABOND
Color	RED
Material	RETAINING COMPOUND
Grade Standard	BEARING RETAINING
Packaging Type	BOTTLE
Usage/Application	Withstand vibration

GST TAX : 18% INCLUDING.

PACKING 10 ML
Anabond Bearing Retainer is a single component anaerobic adhesive. They permit fitment of bearings onto worn-out shafts & housings. Eliminates need for welding, punching. knurling, metallising and remachining of shafts and housings. Permits slip fitment of bearings, bushes, gears and sleeves.
The Perfect Mounting Technology. NOT suitable for wood and synthetic material.
Enhances reliability. • Save time and money. • Distributes load evenly. • Very high shear strength. • Prolongs life of assembly. • Withstands severe shock loads
Prevents wearout of housing and shafts. • Much superior to conventional press fits. • Salvages undersized shafts and oversized housings.
Suitable upto a clearance of 7 Thou (0.175mm). Endures temperature from -60 C to 150 C.
Resistant to water, oil, fuel and most chemicals. Air content in the bottle keep the product liquid.

Additional Information:

Delivery Time: WITHIN 2 DAYS
Packaging Details: 5 ML,10ML,50ML,250 ML

View Complete details

get quote request a call back

Fasto A348 Retaining Adhesive

Rs 463 / PieceGet Best Price

Form	Liquid
Adhesion Properties	Pressure Sensitive
Chemical Composition	Silicone
Origin	Synthetic
Packaging Size	50 ml also available in 250 ml

Features:

High temperature

Fast curing

Provides perfect seal

Temperature resistance

High bond strength

Price:Pack sizePriceGst Extra250 ml211618%

Additional Information:

Item Code: Fasto-A348

View Complete details

get quote request a call back

ANR 638 Bearing Retainer

Rs 310 / PieceGet Best Price

Minimum Order Quantity: 30 Piece

Viscosity	2500-3000
Static Shear Strength	28 N/mm2
Gap Fill MM	0.25
Fixture time	10 Min
Full Cure	24 Hrs
Temperature Resistance	-50 to 150 degree C
Applications	Retaining of cylindrical parts such as bearings, bushes gears , pullies, etc. in automobile and engi
Color	Green

Riding on unfathomable volumes of industrial expertise, we are providing a broad array of ANR 638 Bearing Retainer.

Details:

These are specially formulated anaerobic retaining compounds designed to provide holding and retaining power
for round and cylindrical parts, such as bearings.

Salient Features & Benefits:

Heavy duty retainer
Prevents fretting corrosion
Allows uniform load distribution
Eliminates interference fits
Dampens vibrations, shocks and impact loads

View Complete details

get quote request a call back

ANR 126 Bearing Retainer

Rs 135 / PieceGet Best Price

Minimum Order Quantity: 30 Piece

Color	Green
Viscosity	1000-1500
Static Shear Strength	16 N/mm2
Gap Fill	0.25 MM
Fixture time	10 Min
Full Cure	24 Hrs
Temperature Resistance	-50 to 150
Applications	Cylinder head assemblies flywheel, engine a engine assemblies, gear shifting assembly, trance axle a

With the valuable assistance of skilled team of professionals, we are engaged in offering an extensive range of high-quality ANR 126 Bearing Retainer.

View Complete details

get quote request a call back

Loctite 641 Bearing Retaining Compound

Rs 508 / NumberGet Best Price

Minimum Order Quantity: 5 Number

Product Brochure

Grade Standard	Technical Grade
Brand	Loctite
Packaging Size	50 ml
Usage	Industrial
Color	yellow
Packaging Type	Bottle
Shear Strength	Medium
Cure Time	30 minutes
Service Temperature	77 f
Technology	German
Material	liquid
Common Application	metal steel
Chemical Composition	Methacrylate ester
Components	Retaining
Cure Method	25 minutes
Fixture Time	25 minutes
Gap Fill Mm	0.003937007874015749 in.
Strength Required	Medium

Technical Information

Color	Yellow
Fixture Time	25 min.
Fixture Time Temperature	77 °F
Gap Fill	0.003937007874015749 in.
Substrates	Metal: Steel Retaining Compound - medium strength. If disassembly is required. Ideal for parts that need subsequent dismantling. LOCTITE® 641 is designed for the bonding of cylindrical fitting parts, particularly where disassembly is required for servicing operations. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings

Additional Information:

Delivery Time: within 2 days
Packaging Details: 50 ml & 250 ml

View Complete details

get quote request a call back

Fasto A350 Bearing Retaining Compound

Rs 350 / NumberGet Best Price

Minimum Order Quantity: 10 Number

Product Brochure

Grade Standard	Technical Grade
Brand	FASTO
Packaging Size	50 ML
Usage	Industrial
Packaging Type	BOTTLE
Shear Strength	34 /N/M2
Cure Time	12 HOUR
Service Temperature	21 C
Diametric Clearance	0.25MM

Fasto A350 is a single component, super fast curing and super high strength anaerobic retaining compound. Fasto A350 is formulated for retaining & sealing cylindrical parts. Fasto A350 offers excellent heat resistance. Once applied, parts slip together easily, lubricated by the adhesives. Fasto A350 cures when confined in the absence of air between close-fitting metal surfaces. Fasto A350 prevents corrosion of assembling parts.TYPICAL APPLICATIONSTypical applications include retaining of locking sleeves, bushes, bearings, pulleys, sprockets, gears, etc onto shafts. Fasto A350 is also used for retaining rotors, plugs and many more cylindrical assemblies. It can also be used for sealing & locking threads. Typically Fasto A350 can be used in motors, pumps, gearboxes, turbines, compressors generators, shower panels and many more industrial & automotive assemblies.PROPERTIES OF UNCURED MATERIALValueChemical type DimethacrylateAppearance GreenSpecific Gravity ~1.08Viscosity cPs1Shear Strength 1500- 25002 (N/mm2Fixture Time) 343Full Cure (hours) 12 (mins) <8Shelf Life@ 21°C (months) 12Max Gap Fill (mm) 0.20Operating TemperatureRange (°C) -50 to +175Intermittent (2hrs to 4 hrs) upto 2101 Brookfield LVF Spindle 2, 2.5rpm2 On mild steel pin and collar, ISO 101233 ISO 10964.

Additional Information:

Delivery Time: within 2 days

View Complete details

get quote request a call back

LOCTITE 638 BEARING RETAINING

Rs 508 / NOSGet Best Price

Minimum Order Quantity: 10 NOS

Product Brochure

Brand	LOCTITE
Color	GREEN LIQUID
Material	Anerobic
Packaging Type	bottle
Usage/Application	rottary,shaft,bearing
Weight	50 ml & 250 ml

LOCTITE® 638™ provides the following product characteristics: Technology Acrylic Chemical Type Urethane methacrylate Appearance (uncured) Green liquidLMS Fluorescence Positive under UV lightLMS Components One component - requires no mixing Viscosity High Cure Anaerobic Secondary Cure Activator Application Retaining Strength High This Technical Data Sheet is valid for LOCTITE® 638™ manufactured from the dates outlined in the "Manufacturing Date Reference" section. LOCTITE® 638™ is designed for the bonding of cylindrical fitting parts, particularly where bond gaps can approach 0.25 mm and where maximum strength at room temperature is required. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. Typical applications include locking bushings and sleeves into housings and on shafts. LOCTITE® 638™ provides robust curing performance. It not only works on active metals (e.g. mild steel) but also on passive substrates such as stainless steel and plated surfaces. The product offers high temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids. NSF International Registered to NSF Category P1 for use as a sealant where there is no possibilty of food contact in and around food processing areas. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification.
TYPICAL PROPERTIES OF UNCURED MATERIAL Specific Gravity @ 25 °C 1.1 Flash Point - See SDS Viscosity, Brookfield - RVT, 25 °C, mPa·s (cP): Spindle 3, speed 20 rpm 2,000 to 3,000LMS Viscosity, Cone & Plate, 25 °C, mPa·s (cP): Shear rate 129 s -1 1,900 to 3,100.
1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry. 2. To accelerate cure speed or where large gaps are present, use activator and allow to dry. 3. For Slip Fitted Assemblies, apply adhesive around the leading edge of the pin and the inside of the collar and use a rotating motion during assembly to ensure good coverage. 4. For Press Fitted Assemblies, apply adhesive thoroughly to both bond surfaces and assemble at high press on rates. 5. For Shrink Fitted Assemblies, the adhesive should be coated onto the part to produce a smooth, even film of material. If heating the hub for assembly, coat the pin. If the pin is to be cooled for assembly, coat the hub. If both heating and cooling is to be done, apply material to cooled part. Avoid condensation on cooled parts. 6. Parts should not be disturbed until sufficient handling strength is achieved. For Disassembly 1. Remove with standard hand tools. 2. If needed, apply localized heat to the assembly to approximately 250 °C. Disassemble while hot. 3. If this temperature is not possible, heat as much as possible and use mechanical aids. For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush. Loctite Material SpecificationLMS LMS dated July-11, 2013. Test report

Additional Information:

Delivery Time: within 2 days
Packaging Details: 50 ml & 250 ml

View Complete details

get quote request a call back

Loctite 638 Bearing Retainer

Rs 510 / NumberGet Best Price

Minimum Order Quantity: 10 Number

Product Brochure

Brand	LOCTITE
Color	GREEN
Material	LIQUID
Feature	POSITIVE UNDER UV LIGHT
Grade Standard	Anaerbic
Packaging Type	bottle
Usage/Application	leakage from shock and vibration

PRODUCT DESCRIPTIONLOCTITE® 638™ provides the following product characteristics:Technology Acrylic Chemical Type Urethane methacrylate Appearance (uncured) Green liquidLMSFluorescence Positive under UV lightLMSComponents One component -requires no mixingViscosity HighCure AnaerobicSecondary Cure ActivatorApplication RetainingStrength HighThis Technical Data Sheet is valid for LOCTITE® 638™manufactured from the dates outlined in the"Manufacturing Date Reference" section.LOCTITE® 638™ is designed for the bonding of cylindricalfitting parts, particularly where bond gaps can approach 0.25mm and where maximum strength at room temperature isrequired. The product cures when confined in the absence ofair between close fitting metal surfaces and prevents looseningand leakage from shock and vibration. Typical applicationsinclude locking bushings and sleeves into housings and onshafts. LOCTITE® 638™ provides robust curing performance.It not only works on active metals (e.g. mild steel) but alsoon passive substrates such as stainless steel and platedsurfaces. The product offers high temperature performanceand oil tolerance. It tolerates minor surface contaminationsfrom various oils, such as cutting, lubrication, anti-corrosionand protection fluids.NSF InternationalRegistered to NSF Category P1 for use as a sealant wherethere is no possibilty of food contact in and around foodprocessing areas. Note: This is a regional approval. Pleasecontact your local Technical Service Center for moreinformation and clarification.TYPICAL PROPERTIES OF UNCURED MATERIALSpecific Gravity @ 25 °C 1.1Flash Point - See SDSViscosity, Brookfield - RVT, 25 °C, mPa·s (cP):Spindle 3, speed 20 rpm 2,000 to 3,000LMSViscosity, Cone & Plate, 25 °C, mPa·s (cP):Shear rate 129 s-1 1,900 to 3,100
TYPICAL CURING PERFORMANCECure Speed vs. SubstrateThe rate of cure will depend on the substrate used. The graphbelow shows the shear strength developed with time on steelpins and collars compared to different materials and testedaccording to ISO 10123.% of Full Strength on SteelCure Time10075502505m 10m 30m 1h 4h 8h 24h 72h 168hSteelAluminumStainless steelCure Speed vs. Bond GapThe rate of cure will depend on the bondline gap. The followinggraph shows shear strength developed with time on steel pinsand collars at different controlled gaps and tested according toISO 10123.% of Full Strength on SteelCure Time10075502505m 10m 30m 1h 4h 8h 24h 72h 168h0.15 mm0.25 mm0.05 mmCure Speed vs. TemperatureThe rate of cure will depend on the temperature. The graphbelow shows the shear strength developed with time atdifferent temperatures on steel pins and collars and testedaccording to ISO 10123.Cure Speed vs. ActivatorThe graph below shows the shear strength developed withtime on stainless steel pins and collars using Activator SF7471™, SF 7649™ and SF 7091™ and tested according toISO 10123.
Compressive Shear Strength, ISO 10123:Steel pins and collars N/mm² 29(psi) (4,200)Stainless Steel pins and collars N/mm² 28(psi) (3,990)Aluminum pins and collars N/mm² 17(psi) (2,710)After 24 hours @ 22 °CBreakaway Torque, ISO 10964:M10 black oxide bolts and mildsteel nutsN·m 57(lb.in.) (505)3/8 x 16 steel nuts (grade2) and bolts (grade 5)N·m 25(lb.in.) (220)Prevail Torque, ISO 10964:M10 black oxide bolts and mildsteel nutsN·m 22(lb.in.) (195)3/8 x 16 steel nuts (grade2) and bolts (grade 5)N·m 9.4(lb.in.) (85)Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m:3/8 x 16 steel nuts (grade2) and bolts (grade 5)N·m 23(lb.in.) (205)Prevail Torque, ISO 10964, Pre-torqued to 5 N·m:3/8 x 16 steel nuts (grade2) and bolts (grade 5)N·m 12(lb.in.) (105)

Additional Information:

Delivery Time: within 2 days

View Complete details

get quote request a call back

Loctite 648 Bearing Retaining

Rs 792 / NumberGet Best Price

Minimum Order Quantity: 10 Number

Product Brochure

Brand	LOCTITE
Color	GREEN LIQUID
Material	Urethane methacrylate
Feature	POSSITIVE UNDER UV LIGHT
Form	LIQUID
Grade Standard	LOCTITE 648
Packaging Type	BOTTLE
Usage/Application	Typical applications include holding gears and sprockets onto gearbox shafts and rotors on electric
Weight	50 ML & 250 ML

PRICE IS 50 ML PACK .
RATE ARE INCLUSIVE OF GST 18%.

PRODUCT DESCRIPTIONLOCTITE® 648™ provides the following product characteristics:Technology Acrylic Chemical Type Urethane methacrylateAppearance (uncured) Green liquidLMSFluorescence Positive under UV lightLMSComponents One component -requires no mixing Viscosity Low Cure Anaerobic Secondary Cure Activator Application Retaining Strength High This Technical Data Sheet is valid for LOCTITE® 648™manufactured from the dates outlined in the"Manufacturing Date Reference" section.LOCTITE® 648™ is designed for the bonding of cylindricalfitting parts. The product cures when confined in the absenceof air between close fitting metal surfaces and preventsloosening and leakage from shock and vibration. Typicalapplications include holding gears and sprockets onto gearboxshafts and rotors on electric motor shafts. LOCTITE® 648™provides robust curing performance. It not only works on activemetals (e.g. mild steel) but also on passive substrates such asstainless steel and plated surfaces. The product offers hightemperature performance and oil tolerance. It tolerates minorsurface contaminations from various oils, such as cutting,lubrication, anti-corrosion and protection fluids.
TYPICAL PROPERTIES OF UNCURED MATERIALSpecific Gravity @ 25 °C 1.1Viscosity, Brookfield - RVT, 25 °C, mPa·s (cP):Spindle 2, speed 20 rpm 400 to 600LMSViscosity, Cone & Plate, 25 °C, mPa·s (cP):Shear rate 129 s-1 400 to 600Flash Point - See SDS
TYPICAL CURING PERFORMANCECure Speed vs. SubstrateThe rate of cure will depend on the substrate used. The graphbelow shows the shear strength developed with time on steelpins and collars compared to different materials and testedaccording to ISO 10123.
Cure Time10075502505m 10m 30m 1h 4h 8h 24h 72h 168hSteelAluminumStainless steelCure Speed vs. Bond GapThe rate of cure will depend on the bondline gap. The followinggraph shows shear strength developed with time on steel pinsand collars at different controlled gaps and tested according toISO 10123.% of Full Strength on SteelCure Time10075502505m 10m 30m 1h 4h 8h 24h 72h 168h0.25 mm0.15 mm0.05 mmCure Speed vs. TemperatureThe rate of cure will depend on the temperature. The graphbelow shows the shear strength developed with time atdifferent temperatures on steel pins and collars and testedaccording to ISO 10123.
Cure Time15012510075502505m 10m 30m 1h 4h 8h 24h 72h 168h40 °C22 °C5 °CCure Speed vs. ActivatorThe graph below shows the shear strength developed withtime on stainless steel pins and collars using Activator SF7471™, SF 7649™ and SF 7091™ and tested according toISO 10123.% of Full Strength on SteelCure Time10075502505m 10m 30m 1h 4h 8h 24h 72h 168hActivator SF 7471™Activator SF 7649™No activatorActivator SF 7091™TYPICAL PROPERTIES OF CURED MATERIALPhysical Properties:Glass Transition Temperature ISO 11359-2, °C 100Coefficient of Thermal Expansion, ISO 11359-2 K-1:Below Tg 93×10-06Above Tg 184×10-06TYPICAL PERFORMANCE OF CURED MATERIALAdhesive PropertiesCured for 15 minutes @ 22 °CCompressive Shear Strength, ISO 10123:Steel pins and collars N/mm² ≥13.5LMS(psi) (1,960)Cured for 24 hours @ 22 °CCompressive Shear Strength, ISO 10123:Steel pins and collars N/mm² ≥25LMS(psi) (≥3,625)Cured for 7 days @ 22°C
Shear Strength, ISO 10123:Steel pins and collars N/mm² 31(psi) (4,480)Stainless Steel pins and collars N/mm² 30(psi) (4,350)Aluminum pins and collars N/mm² 18(psi) (2,610)Cured for 24 hours @ 22°CBreakaway Torque, ISO 10964:M10 black oxide bolts and mild steelnutsN·m 58(lb.in.) (515)3/8 x 16 steel nuts (grade 2) and bolts(grade 5)N·m 32(lb.in.) (285)Prevail Torque, ISO 10964:M10 black oxide bolts and mild steelnutsN·m 40(lb.in.) (355)3/8 x 16 steel nuts (grade 2) and bolts(grade 5)

Additional Information:

Production Capacity: AVAILABLE
Delivery Time: WITHIN TWO DAY
Packaging Details: 50 ML & 2500 ML

View Complete details

get quote request a call back

Loctite 648 Bearing Retaining Compound

Rs 3,521 / NumberGet Best Price

Minimum Order Quantity: 10 Number

Grade Standard	Technical Grade
Brand	LOCTITE
Type	industrial
Packaging Size	50 ML & 250 ml
Usage/Application	Industrial
Packaging Type	BOTTLE
Shear Strength	HIGH STRENGTH
Cure Time	5 MM 10 MINUTES
Service Temperature	250 C
Common Application	BEARING
Color	green

ABOVE PRICE IS 250 ML PACK .
RATE ARE INCLUSIVE OF GST 18%.

PRODUCT DESCRIPTIONLOCTITE® 648™ provides the following product characteristics:Technology Acrylic Chemical Type Urethane methacrylate Appearance (uncured) Green liquidLMS Fluorescence Positive under UV lightLMS Components One component -requires no mixing Viscosity LowCure AnaerobicSecondary Cure ActivatorApplication RetainingStrength High
This Technical Data Sheet is valid for LOCTITE® 648™manufactured from the dates outlined in the"Manufacturing Date Reference" section.LOCTITE® 648™ is designed for the bonding of cylindricalfitting parts. The product cures when confined in the absenceof air between close fitting metal surfaces and preventsloosening and leakage from shock and vibration. Typicalapplications include holding gears and sprockets onto gearboxshafts and rotors on electric motor shafts. LOCTITE® 648™provides robust curing performance. It not only works on activemetals (e.g. mild steel) but also on passive substrates such asstainless steel and plated surfaces. The product offers hightemperature performance and oil tolerance. It tolerates minorsurface contaminations from various oils, such as cutting,lubrication, anti-corrosion and protection fluids.TYPICAL PROPERTIES OF UNCURED MATERIALSpecific Gravity @ 25 °C 1.1Viscosity, Brookfield - RVT, 25 °C, mPa·s (cP):Spindle 2, speed 20 rpm 400 to 600LMSViscosity, Cone & Plate, 25 °C, mPa·s (cP):Shear rate 129 s-1 400 to 600Flash Point - See SDS
TYPICAL CURING PERFORMANCECure Speed vs. SubstrateThe rate of cure will depend on the substrate used. The graphbelow shows the shear strength developed with time on steelpins and collars compared to different materials and testedaccording to ISO 10123.Cure Speed vs. Bond GapThe rate of cure will depend on the bondline gap. The followinggraph shows shear strength developed with time on steel pinsand collars at different controlled gaps and tested according toISO 10123.
Cure Speed vs. TemperatureThe rate of cure will depend on the temperature. The graphbelow shows the shear strength developed with time atdifferent temperatures on steel pins and collars and testedaccording to ISO 10123.
Compressive Shear Strength, ISO 10123:Steel pins and collars N/mm² 31(psi) (4,480)Stainless Steel pins and collars N/mm² 30(psi) (4,350)Aluminum pins and collars N/mm² 18(psi) (2,610)Cured for 24 hours @ 22°CBreakaway Torque, ISO 10964:M10 black oxide bolts and mild steelnutsN·m 58(lb.in.) (515)3/8 x 16 steel nuts (grade 2) and bolts(grade 5)N·m 32(lb.in.) (285)Prevail Torque, ISO 10964:M10 black oxide bolts and mild steelnutsN·m 40(lb.in.) (355)3/8 x 16 steel nuts (grade 2) and bolts(grade 5)N·m 16(lb.in.) (140)Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m:3/8 x 16 steel nuts (grade 2) and bolts(grade 5)N·m 29(lb.in.) (255)Prevail Torque, ISO 10964, Pre-torqued to 5 N·m:3/8 x 16 steel nuts (grade 2) and bolts(grade 5)N·m 29(lb.in.) (255)
TYPICAL PROPERTIES OF CURED MATERIALPhysical Properties:Glass Transition Temperature ISO 11359-2, °C 100Coefficient of Thermal Expansion, ISO 11359-2 K-1:Below Tg 93×10-06Above Tg 184×10-06TYPICAL PERFORMANCE OF CURED MATERIALAdhesive PropertiesCured for 15 minutes @ 22 °CCompressive Shear Strength, ISO 10123:Steel pins and collars N/mm² ≥13.5LMS(psi) (1,960)Cured for 24 hours @ 22 °CCompressive Shear Strength, ISO 10123:Steel pins and collars N/mm² ≥25LMS(psi) (≥3,625)

Additional Information:

Production Capacity: IMMEDIATE
Delivery Time: WITHIN 2 DAYS
Packaging Details: 50 ML & 250 ML GST EXTRA

View Complete details

get quote request a call back

ANABOND 412 BEARING RETAINER

Rs 155 / NOSGet Best Price

Minimum Order Quantity: 25 NOS

Product Brochure

Brand	ANABOND
Color	RED
Material	LIQUID
Grade Standard	BEARING RETAINING
Packaging Type	BOTTLE
Usage/Application	FOR HIGH STRENGTH
Weight	50 ML & 250 ML
Country of Origin	Made in India

HIGH STRENGTH BEARING RETAINERS, COLOR RED, CURING TIME : 10 TO 15 MINUTES SHEAR STRENGH : 200-250 KG/CM2 VISCOSITY : 275-325 CPS GAP FILLED 0.175 MM
SERVICE TEMPERATURE : 060 TO 150

Additional Information:

Item Code: 412
Production Capacity: AHMEDABAD
Delivery Time: WITHIN 2 DAYS
Packaging Details: 50 ML & 250 ML

View Complete details

get quote request a call back

Fasto A301 Retaining Adhesive

Rs 349 / PieceGet Best Price

Packaging Size	50 ml also available in 250 ml
Chemical Composition	Silicone
Adhesion Properties	Pressure Sensitive
Origin	Synthetic
Form	Liquid

Features:

Low viscosity
Medium strength
Optimum adhesive quality
Prevent corrosion
Low viscosity

Price:

Pack size	Price	Gst Extra
250 ml	1622	18%

Additional Information:

Item Code: Fasto-A301

View Complete details

get quote request a call back

FASTO LOCKSEAL

Rs 160 / NumberGet Best Price

Minimum Order Quantity: 10 Number

Brand	FASTO
Color	RED
Material	LIQUID

Fasto Lockseal is General purpose Anerobic.Its used for Retaining,Locking,Sealing,Purpose.It is performance & High strengh Anerobic product.
Apply to mating surface.Assemble parts,handling strengh will be achieved minutes to an Hour.

Additional Information:

Delivery Time: within 2 days

View Complete details

get quote request a call back

EXPLORE MORE CATEGORIES

Lube Adhesive & Engineering Co.

Bearing Retainer

ANR 122 Bearing Retainer Adhesive

Anabond 402 Bearing Retainer Adhesives

Fasto A338 Retaining Adhesive

Fasto A339 Retaining Adhesive

Fasto A341 Retaining Adhesive

Fasto A360 Retaining Adhesive

Fasto A320 Retaining Adhesive

ANABOND BEARING RETAINER

Fasto A348 Retaining Adhesive

ANR 638 Bearing Retainer

ANR 126 Bearing Retainer

Loctite 641 Bearing Retaining Compound

Fasto A350 Bearing Retaining Compound

LOCTITE 638 BEARING RETAINING

Loctite 638 Bearing Retainer

Loctite 648 Bearing Retaining

Loctite 648 Bearing Retaining Compound

ANABOND 412 BEARING RETAINER

Fasto A301 Retaining Adhesive

FASTO LOCKSEAL

EXPLORE MORE CATEGORIES

Epoxy Adhesive

Silicone Sealant

Adhesive Sealant

Cyanoacrylate Adhesive

Rubber Adhesive

Wood Adhesive

Thread Locking Adhesive

Polyurethane Adhesives