Lube Adhesive & Engineering Co.

ABOVE PRICE IS INCLUDING GST 18%  

Description Lapox Metalam - B is two component modified, epoxy coating system. When both components aremixed in recommended ratios and cured appropriately at room temperature, an excellent coating orlamination can be achieved on most of the substrates including glass, metals, plastics, wood, paperstickers and natural stones. Faster productivity can be achieved, if curing is performed at highertemperature between 40°C and 60°C. Curing at higher temperature is recommended to achieveoptimum bond strength.Applications BucklesCoating and lamination of articlesKey-chainMetal gift articlesPaper stickersPVCAdvantages Good colour stabilityGood flexibility and adhesionHigh gloss and clarityThermally stable and suitable to perform in extreme conditionsWater and chemical resistantTypical specifications Test Unit Reference ValueResin HardenerDescription - Visual Clear, transparentliquidClear, transparentliquidViscosity at 25°C1 m Pas ASTM D2196 800 - 1,200 300 - 600Colour APHA ASTM D1209 Max 60 -Colour GS ASTM D1544 - Max 1Density g/cc ASTM D792 1.00 - 1.20 0.95 - 1.001Viscosity by Brookfield viscometerMix specifications Test Unit Reference ValueMixing ratio (resin : hardener) w/w - 100 : 50Mix viscosity at 25°C m Pas ASTM D2196 500 - 800Pot life1 Minutes ASTM D2471 20 - 35Peak exotherm temperature2 °C ASTM D2471 Max 75Surface dry* Hours ASTM D5895 150 - 180Touch dry* Hours ASTM D5895 230 - 260Optical clarity Visual - Excellent1Pot life of 100 g mix mass at 25 ± 1°C in plastic disposable cup by ‘Gardco’ gel timer2Total 100 g mix mass in plastic disposable cup at 25°C*Drying time of 200 micron film on glass plate at 25°CAfter cure specifications Test Unit Reference ValueWater absorption (24 hours immersion) % ASTM D670-63 Max 0.5Hardness of 10 mm casting (after 24 hours) Shore D ISO/ R868 60 - 65
Processing Surface preparation: The substrate must be thoroughly degreased with a good degreasing solvent(e.g. toluene, acetone trichloroethylene). Ensure the surface is free form the dirt, oil, grease andmoisture. Wipe off the surface with clean cloth. Inadequately pre-treated substrates may not yieldsatisfactory results.Application: The mixed mass is applied by brush, spatula or through dispensing bottle on thesurface to be coated. The mix must be used within its pot life.Curing: Curing normally takes place at room temperature within about 24 hours depending on theambient temperature but may be accelerated by the application of heat.Packaging Lapox Metalam - B is available in 1.5 Kg bottles and 7.5 kg HDPE jerry cans. Other packing may beconsidered on request.

ABOVE PRICE IS INCLUDING GST 18%
Araldite® 2014 Two component epoxy paste adhesive Key properties • Grey paste • High temperature and chemical resistance • Low shrinkage • Very resistant to water and a variety of chemicals • Gap filling, non sagging up to 0.197 in (5 mm) thickness
Description Araldite ® 2014 structural adhesive is a two component, room temperature curing, thixotropic paste adhesive of high strength with good environmental and excellent chemical resistance. Used for bonding of metals, electronic components, GRP structures and many other items where a higher than normal temperature or more aggressive environment is to be encountered in service. The low out gassing makes this product suitable for specialist electronic telecommunication and aerospace applications.
Product data Property 2014/A 2014/B 2014 (mixed) Color (visual) beige paste grey paste grey paste Specific gravity ca. 1.6 ca. 1.6 ca. 1.6 Viscosity at 77°F (cP) ca. 100,000 thixotropic thixotropic Pot Life (100 gm at 77°F) - - ~ 40 minutes Shelf life (36°F-104o F) 3 years 3 years
Processing Pretreatment The strength and durability of a bonded joint are dependant on proper treatment of the surfaces to be bonded. At the very least, joint surfaces should be cleaned with a good degreasing agent such as acetone or other proprietary degreasing agents in order to remove all traces of oil, grease and dirt. Low grade alcohol, gasoline, or paint thinners should never be used. The strongest and most durable joints are obtained by either mechanically abrading or chemically etching (“pickling”) the degreased surfaces. Abrading should be followed by a second degreasing treatment. Mix ratio Parts by weight Parts by volume Araldite 2014/A adhesive 100 100 Araldite 2014/B adhesive 50 50 Araldite 2014 structural adhesive is available in cartridges incorporating mixers and can be applied as ready to use adhesive with the aid of the tool recommended by Huntsman Advanced Materials
Times to minimum shear strength Temperature °F 50 59 73 104 140 212 Cure time to reach hours 14 8 3 - - - LSS > 145 psi (1MPa) minutes - - - 60 15 3 Cure time to reach hours 20 11 5 - - - LSS > 1450 psi (10MPa) minutes - - - 80 20 4 LSS = Lap shear strength.Times to minimum shear strengthTemperature °F 50 59 73 104 140 212 Cure time to reach hours 14 8 3 - - - LSS > 145 psi (1MPa) minutes - - - 60 15 3 Cure time to reach hours 20 11 5 - - - LSS > 1450 psi (10MPa) minutes - - - 80 20 4 LSS = Lap shear strength. 

Application: . Bluecoat D3 is a non-structuraI adhesive for joining wood andderived timber products such as bonding of furnitureinternaI structures, pane[ing, doors, windows [amination etc'. ldeaI for edge bonding, joinery application, handicrafts,modular furniture, coLd Press / hot press, post formingappLication & wooden flooring.. For bonding laminates, plywood, veneer, blocl<-board, hardboard,MDF etc.. Bluecoat D5 is to be used in ptaces where there isintermittent water spLashing which makes it high waterresistance.SpeciaLfeatures : . Tested and approved by teading German laboratory. High strength cross Linking adhesive. Water proof e high heat resistant adhesive. Fast setting time. Suitable for both hot and cold Press . Powerful bond strength & higher coverageSpecification: . Conforms to EN 2o4 for D3 standardStorage precaution:. Store away from direct heat & sunLight. l(eep the containertightLy ctosed when notin usePacking: . Avai[abte in pacl<s of 1l<g,51<g, 1ol<g,2ol<g,5ol<g,6ol<9

500 GM PACK : ABOVE PRICE IS INCLUDING GST  18%
ORDERING INFORMATION STOCK NO.: 10112 PACKAGE SIZE: 500g STOCK NO.: 10115 PACKAGE SIZE: 1kg STOCK NO.: 10117 PACKAGE SIZE: 10Kg DESCRIPTION The original metal filled epoxy putty for economical, dependable maintenance and repair work. RECOMMENDED APPLICATIONS • Repairs cracks and breaks in equipment, machinery or castings • Patches and rebuilds blow holes or pits in castings • Rebuilds worn equipment, pumps and valve bodies • Restores bearing journals and racesPRODUCT DATA TYPICAL PHYSICAL PROPERTIES COLOUR Grey MIX RATIO BY VOLUME 2.5:1 MIX RATIO BY WEIGHT 9:1 % SOLIDS BY VOLUME 100 POT LIFE AT 25OC/ MINS 45 SPECIFIC VOLUME CC/KG 429 CURED SHRINKAGE CM/CM 0.0006 SPECIFIC GRAVITY 2.33 TEMPERATURE RESISTANCE Dry 121o C COVERAGE 858cm2 /Kg @ 5mm CURED HARDNESS / SHORE D 85 D DIELECTRIC STRENGTH KV/MM 1.18 ADHESIVE TENSILE SHEAR / MPA 19 COMPRESSIVE STRENGTH MPA 57 COEFFICIENT OF THERMAL EXPANSION X10-6 CM/CM/OC 86.4 THICKNESS PER COAT / MM As Required FUNCTIONAL CURE TIME /HOURS 16 RECOAT TIME / MINUTES 4 MIXED VISCOSITY /CPS (WHERE APPLICABLE) PuttyCHEMICAL RESISTANCE - 7 DAYS ROOM TEMPERATURE CURE (30 DAYS) - TESTING CARRIED OUT 30 DAYS IMMERSION AT 21°C POOR FAIR VERY GOOD EXCELLENT AMMONIA • CUTTING OIL • ISOPROPYL ALCOHOL • GASOLINE (UNLEADED) • HYDROCHLORIC ACID 37% • METHYL ETHYL KETONE (MEK) • METHYLENE CHLORIDE • SODIUM HYPOCHLORITE 5% (BLEACH) • SODIUM HYDROXIDE 50% • SULPHURIC ACID 98% • XYLENE • Excellent = +/- 1% weight change, Very Good = +/- 1-10% weight change, Fair = +/- 10-20% weight change, Poor = > 20% weight changeAPPLICATION INFORMATION CURE A 12.7mm thick section of Devcon Plastic Steel Putty will harden at 21ºC in 4 hours. The material will be fully cured in 16 hours at which time the material can be machined, drilled or painted. The actual cure time of epoxy is determined by the mass used and the room temperature at time of repair. SURFACE PREPARATION Proper surface preparation is essential to a successful application. The following procedures should be considered:

ABOVE PRICE OF INCLUDING GST 18%.
Properties Specification Chemical type 2K Epoxy Appearance Part A (Resin) Part B (Hardener) Viscous paste Viscous paste Colour Part A Part B Mixed Milky white Off white Off white Mix Ratio by weight 100 : 50 (2:1) Pot life @RT (100g mix) Min. 30 minutes Dry time ≤2 hours Curing condition @ RT 48 hoursAquabond 520 is a two-component highperformance compound. This adhesive system is specially formulated using bis – epi type epoxy resin filled with inorganic fillers in part A & poly amido amine with inorganic fillers in part B. When the resin and hardener are mixed, it cures to produce a completely cross linked net works, which has excellent resistance to water, oils, industrial solvents etc.PropertiesLap shear strength @ RT Mild steel to Mild steel Compression strength @RT Tensile strength @RT Hardness, Shore D Page 1 of 2 Properties of Cured Material Typical Applications Bonding and sealing operations under humid wet Mix part A and Part B separately well before use. Part B in the ratio of 2:1 on to a plastic container. Mix well 3 to 5 minutes to get an uniform and homogenous paste. Clean the area where repairing has to be performed so that it is free from oil, grease, dust, rust etc. Apply sufficient mixed material. Leave it undisturbed for 48 hours for curing at room temperature. Care should be taken to use the mixed material within a period of 30 minutes after mixing. Technical Data Sheet March 2013 Total pages 2 Specification ≥ 100 kg/cm2 (≥ 10 Mpa) Compression strength @RT ≥ 400 kg/cm2 (≥ 40 Mpa) ≥180 kg/cm2 (≥ 18 Mpa) ≥ 80Mix part A and Part B separately well before use.Weigh part A & Part B in the ratio of 2:1 on to a plastic container. Mix well 3 to 5 minutes to get an uniform and homogenous paste. Clean the area where repairing has to be performed so that it is free from oil, grease, dust, rust etc. Apply sufficient quantity of the mixed material. Leave it undisturbed for 48 hours for curing at room temperature. Care should be taken to use the mixed material within a period of 30 minutes after mixing.Shelf LifePart A & B : 12 months from the date of manufacture when stored room temperature in unopened container.  

ABOVE PRICE IS 9 KG SET  INCLUDING GST 18% . RESIN 9 KG & HARDNER 3KG
Ambient cure low viscous casting system Description Lapox Granito Cast is two component modified, epoxy based system suitable for clear castingapplication. The system is clear, having excellent optical properties with negligible shrinkageoncuring. Faster productivity can be achieved, if curing is performed at higher temperaturebetween40°C and 60°C. Curing at higher temperature is recommended to achieve optimumperformance. Applications Casting of decorative parts Handicraft items Paper weights Table top Advantages Excellent clarity Good hardness development Good wetting properties High gloss finish Long pot life Low viscosity Water and chemical resistantTypical specifications 1Viscosity by Brookfield viscometer Test Unit Reference Value Resin Hardener Description - Visual Clear, transparent liquid Clear liquidViscosity at 25°C1 m Pas ASTM D2196 1,600 - 2,600 10 - 25 Colour APHA ASTM D1209 Max 40 -- Specific gravity - - 1.15 - 1.20 0.92 - 0.96 Mix specifications 1Pot life of 100 g mix mass at 25 ± 1°C in plastic disposable cup by ‘Gardco’ gel timer 2Total 100 g mix mass in plastic disposable cup at 25°C Test Unit Reference Value Mixing ratio (resin : hardener) w/w - 100 : 33 Mix viscosity at 25°C m Pas ASTM D2196 400 - 700 Pot life1 Minutes ASTM D2471 450 - 600 Peak exotherm temperature2 °C - Max 55After cure specifications 1Hardness checked for 20 mm casting, after 24 hours curing 2Tg (Glass transition temperature) development behavior Test Unit Reference ValueHardness1 Shore D ISO/ R868 75- 80Water absorption (24 hours immersion) % ASTM D670-63 Max0.4Optical clarity - Visual Excellent Tg, RT curing, 24 hours2 °C DSC 45- 55Tg, Post curing 50°C, 18 hours2 °C DSC 65- 75Tg, Post curing 80°C, 3 hours2 °C DSC 75- 80Processing Mixing: Mixing is critical and must be accurate. Take resin and hardener in desiredratios. Thecombined liquids must be thoroughly mixed, manually or mechanically to completely removeanyhaziness or streaks. Scrap the sides and base of the mixing pot before transferring themixtoadesired mould for casting. It is advisable to apply the vacuum to remove air fromthe mix just priortopouring into the mould. It is important to mix small quantity at a time as epoxy systems tendtogiveexotherm when kept in a mass. Applications: Mix mass should then be poured into a mould. The mould can be hardor madeofsilicone rubber. Moulding can be carried out by gravity or under vacuum. It does not trapair easilyand does not heat up when used properly. Excessive humidity (above ~65%), lowdaylight andlowtemperature (less than 20°C) may retard the curing. Lapox Granito Cast systemmaynot workeffectively in the monsoon season. Ensure ambient material and workshop temperatureisbetween20°C and 35°C and humidity level below 65%. Filled mould can also be kept under vacuumtoachieve air free components. Troubleshooting Problem Cause Uncured after 24 hours to 48 hours Wrong mix ratio and | or low ambient temperatureSticky | greasy | hazy surface High humidity Air bubbles are entrapped Mixing was too fast and did not have time to releaseair Packaging Lapox Granito Cast is available in 1.3 kg bottles, 4 kg jerry cans, 12 kg HDPE carboys and260kgMS | HDPE drums. Other packing may be considered on request. Storage and handling Lapox Granito Cast should be stored in a cool and dry place, preferably in a sealed container andshould not be exposed to direct sunlight. This product has a shelf life of one year, if storedinitsoriginal container between 2°C and 40°C away from humidity and excessive heat.

ABOVE PRICE IS INCLUDING GST 18%.1.08 KG PACK
Other commercial names • Araldite® Progressive • Araldite® Precision • Araldite® Extra Strong Key properties • Multi purpose • Long working life • Low shrinkage • Good resistance to dynamic loading • Bonds a wide variety of materials in common useDescription Araldite® Standard is a multipurpose, two component, room temperature curing, adhesive of high strength and toughness. It is suitable for bonding a wide variety of metals, ceramics, glass, rubber, rigid plastics and most other materials in common use. It is a versatile adhesive for the craftsman as well as most industrial applications. Product data Property Araldite® Standard Resin Araldite® Standard mixed Araldite® Standard Hardener Colour (visual) neutral pale yellow pale yellow Specific gravity ca. 1.17 ca. 0.97 ca. 1.07 Viscosity at 25°C (Pas) 30 - 50 20 – 40 30 - 45 Pot Life (100 g at 25°C) - - 100 – 150 minutes Processing October 2011 Pretreatment The strength and durability of a bonded joint are dependant on proper treatment of the surfaces to be bonded. At the very least, joint surfaces should be cleaned with a good degreasing agent such as acetone, iso-propanol (for plastics) or proprietary degreasing agent in order to remove all traces of oil, grease and dirt. Low grade alcohol, gasoline (petrol) or paint thinners should never be used. The strongest and most durable joints are obtained by either mechanically abrading or chemically etching (“pickling”) the degreased surfaces. Abrading should be followed by a second degreasing treatment.Mix ratio Parts by weight Araldite® Standard Resin Parts by volume 100 Araldite® Standard Hardener 100 80 100 Huntsman Advanced Materials Araldite® Standard Page 1 of 3 October 2011 Araldite® Standard Page 2 of 3 Huntsman Advanced Materials Application of adhesive The resin/hardener mix is applied directly or with a spatula to the pretreated and dry joint surfaces. A layer of adhesive 0.05 to 0.10 mm thick will normally impart the greatest lap shear strength to the joint. Huntsman stresses that proper adhesive joint design is also critical for a durable bond. The joint components should be assembled and secured in a fix position as soon as the adhesive has been applied. Equipment maintenance All tools should be cleaned with hot water and soap before adhesives residues have had time to cure. The removal of cured residues is a difficult and time-consuming operation. If solvents such as acetone are used for cleaning, operatives should take the appropriate precautions and, in addition, avoid skin and eye contact. Times to minimum shear strength Temperature °C 23 Cure time to reach hours 6 LSS > 1MPa minutes Cure time to reach hours 10 LSS > 10MPa minutes LSS = Lap shear strength.