Lube Adhesive & Engineering Co.

We take pleasure to introduce ourselves as one of the renowned firms for providing the best-in-class range of Fasto A473 Flange Sealant Adhesive.

Other detail:

• Fasto A473 is a slow curing flange sealant, recommended for sealing rigid & semi-rigid flanges.
• It can be used for sealing large gearbox flanges, pump housing, machinery covers, etc.
• It offers initial pressure resistance of 0.5 bar after 20 mins.

Being one of the trusted firms in the industry, we are highly engaged in providing a unique range of Fasto A418 Flange Sealant Adhesive.

Other detail:

• Fasto A418 is a single component, medium strength, anaerobic gasket compound.
• Fasto A418 is a 'form-in-place' gasket product designed for multipurpose applications on rigid metal flanges and surfaces like gearbox casings, machinery covers, pump housings, compressor end caps, turbine casings and many more industrial & automobile assemblies.

Price:

We have marked a distinct and dynamic position in the market by providing a high-quality array of Fasto A474 Flange Sealant Adhesive.

Other detail:

• Fasto A474 is recommended for sealing rigid & semi-rigid metal flanges.
• It is fast curing flange sealants that gives instant sealing.
• It can be used for sealing gearbox casings & side covers, pump housing, machinery covers, etc.
• It offers initial pressure resistance of 0.5 bar after 20 mins.

Price:

ABOVEPRICE IS INCLUDING GST 18% 
LOCTITE® 510™ provides the following product characteristics: Technology Acrylic Chemical Type Dimethacrylate ester Appearance (uncured) Opaque pink pasteLMS Components One component - requires no mixing Viscosity High Cure Anaerobic Application Gasketing and sealing Strength MediumLOCTITE® 510™ cures when confined in the absence of airbetween close fitting metal surfaces. This product is a general gasketing product suitable for hand dispensing or screen printing. NSF International Registered to NSF Category P1 for use as a sealant where there is no possibilty of food contact in and around food processing areas. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification.Approved by the Australian Gas Association Certificatenumber 2590 Class II rated working pressure 500 kPa, working temperature -10 to 200°C. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification. TYPICAL PROPERTIES OF UNCURED MATERIAL Specific Gravity @ 25 °C 1.1 Flash Point - See SDS Viscosity, Brookfield - HBT, 25 °C, mPa·s (cP): Spindle TC, speed 2.5 rpm, Helipath 200,000 to 750,000LMS Spindle TC, speed 20 rpm, Helipath 40,000 to 140,000LMSInstant Sealing CapabilityAnaerobic sealants have the ability to resist low on-line test pressures while uncured. This test was performed with uncured product immediately after assembly of an annular polycarbonate sealing surface with an internal diameter of 50 mm and an external diameter of 70 mm. Pressure Resistance, MPa:Induced Gap 0 mm0.02 Induced Gap 0.125 mm 0.01 Induced Gap 0.25 mm 0.01 TYPICAL CURING PERFORMANCE Cure Speed vs. Substrate The rate of cure will depend on the substrate used. The graph below shows the shear strength developed with time on grit blasted steel lap shears compared to different materials and tested according to ISO 4587.Cure Speed vs. Bond GapThe rate of cure will depend on the bondline gap. The graph below shows the shear strength developed with time on grit blasted steel lap shears compared to different controlled gaps and tested according to ISO 4587.Cure Speed vs. TemperatureThe rate of cure will depend on the temperature. The graph below shows the shear strength developed with time at different temperatures on grit blasted steel lap shears and tested according to ISO 4587.