Call 07942838759 82% Response Rate

our range

New Items

  • Henkal Teroson MS 930
  • Henkal Teroson MS 930
  • Henkal Teroson MS 930
Henkal Teroson MS 930

Henkal Teroson MS 930

Rs 660  / PieceGet Best Price

Minimum Order Quantity: 10 Piece

Product Brochure

Packaging Size310ML
Model NumberTEROSON MS 930
BrandHENKAL
Packaging TypeBOTTLE
Application IndustryRepairs, Construction, Wood working
Surface Of ApplicationMetal
FormPASTE
Grade StandardIndustrial
StrengthHigh
Material CompatibilityMetal
Chemical ResistanceAutomotive Fluids
Country of OriginMade in India
ABOVE PRICE IS INCLUDING GST 18%.

TEROSON MS 930 is a multi-purpose, 1-part, white, grey or black, thixotropic silane modified polymer sealant/adhesive that provides good primerless adhesion.TEROSON® MS 930 is a 1-part, white, grey or black, moisture-cured, thixotropic silane modified polymer sealant/adhesive. It is suitable for various applications involving a wide range of substrate materials. It forms a soft elastic product and provides excellent UV and weathering resistance. It complies with UL QMFZ2 for electrical safety.
TEROSON MS 930 is a multi-purpose, 1-part, white, grey or black, thixotropic silane modified polymer sealant/adhesive that provides good primerless adhesion.TEROSON® MS 930 is a 1-part, white, grey or black, moisture-cured, thixotropic silane modified polymer sealant/adhesive. It is suitable for various applications involving a wide range of substrate materials. It forms a soft elastic product and provides excellent UV and weathering resistance. It complies with UL QMFZ2 for electrical safety.
  • Excellent UV and weathering resistance
  • Broad-spectrum primerless adhesion
  • Multi-purpose product
  • Suitable for a wide range of substrate materials
  • Product complies with UL electrical safety standard
Technical Information
Agency Approvals / Certificates / SpecificationsDIN 53504, DIN EN ISO 868
ColourBlack, Grey, White
Cure Rate4.0 hr.
Elongation, at break250.0 %
Full Cure Time24.0 hr.
Key CharacteristicsThixotropic
Physical FormPaste
Tensile Strength, ISO 370.9 MPa


Additional Information:

  • Delivery Time: IMMEDIATE BASIS
  • Packaging Details: 310 ML

View Complete details

get quote request a call back
  • Fevicol Relam Adhesive
  • Fevicol Relam Adhesive
  • Fevicol Relam Adhesive
Fevicol Relam Adhesive

Fevicol Relam Adhesive

Rs 303  / PieceGet Best Price

Minimum Order Quantity: 24 Piece

Packaging Size250 gm
Application AreaWood
Grade StandardIndustrial
StrengthHigh
Material CompatibilityMetal
Chemical TypePASTE FOAM
Chemical ResistanceAutomotive Fluids
ColorWHITE
Country of OriginMade in India
ABOVE PRICE IS INCLUDING GST 18%.
ountry of Origin Made in India
Manufacturer Pedilite
Brand Fevicol Relam
Packaging Size 150 Grams
Packaging Type Squeeze Tube

Features:
- Easy to apply
- Strong Bond



Additional Information:

  • Delivery Time: READY STOCK

View Complete details

get quote request a call back
  • KINGSTONE X ALL ULTRA 999
  • KINGSTONE X ALL ULTRA 999
KINGSTONE X ALL ULTRA 999

KINGSTONE X ALL ULTRA 999

Rs 306  / PieceGet Best Price

Minimum Order Quantity: 24 Piece

Product Brochure

Packaging Size280 ml
ABOVE PRICE IS INCLUDING GST 18%
Color White
Brand Kingston
Packaging Size 280 ml
Application Industry Weatherproofing, HPL Sheet, Construction
Compatible material Rubber, Ceramic, Glass, Plastic, Concrete, Metal, Polyvinyl Chloride, Wood
Grade Standard Industrial Grade
Type Silicone
Features Water Resistant, UV Resistant, Flexible, One Part, Durable, Tear and Crack Proof, Weather Resistant, Non Sagging
Temp. Range -40 C to +150 C
Surface Of Application Metal, Ceramic, Plastic
Curing System Moisture Cure
Tooling Time 10 min
Set Content 25 Piece/box

With sincerity and hard work of our professionals, we have carved a niche for ourselves in this domain by offering premium quality gamut of X ALL Fix N Stix Sealant.

Details:
  • Instant Bonding Solution
  • High Strength Adhesive
  • Multipurpose Pasting Solution
  • Applicable in all Weather Conditions


Additional Information:

  • Packaging Details: 25 PCS/BOX 280 ML



Additional Information:

  • Delivery Time: READY STOCK
  • Packaging Details: 280 ML

View Complete details

get quote request a call back
  • KANSUE WATER PROOF SEAL TAPE
  • KANSUE WATER PROOF SEAL TAPE
  • KANSUE WATER PROOF SEAL TAPE
  • KANSUE WATER PROOF SEAL TAPE
  • KANSUE WATER PROOF SEAL TAPE
  • KANSUE WATER PROOF SEAL TAPE
  • KANSUE WATER PROOF SEAL TAPE
  • KANSUE WATER PROOF SEAL TAPE
  • KANSUE WATER PROOF SEAL TAPE
  • KANSUE WATER PROOF SEAL TAPE
  • KANSUE WATER PROOF SEAL TAPE
KANSUE WATER PROOF SEAL TAPE

KANSUE WATER PROOF SEAL TAPE

Rs 210  / PieceGet Best Price

Minimum Order Quantity: 5 Piece

Product Brochure

Tape Width0-20 mm
Tape Length10 m
Backing MaterialWaterproof polyethylene film
ColorBLACK
BrandKANSUEE
Usage/FeatureLEKAGE OF WATER
MOQ10
Tape TypeAdhesive
Total Thickness0.6+-3.5%
ElongationGOOD
ABOVE PRICE IS INCLUDING GST 18%.

SR.NO PROPERTIES UOM TEST METHOD SPECIFICATION 1 Customer name 2 PRODUCT FEATURES - - (1)Waterproof (2)Works underwater (3)Instantly seals out water, air, & moisture 3 material - - Waterproof polyethylene film 4 Adhesive Type - - Aggressive Natural Rubber 5 Shade - - BLACK 6 Overall Grade/Function - - Premium Performance KANSUEE INDUSTRIES PVT LTD TECHNICAL DATA SHEET FOR WATERPROOF SEAL TAPE (KANSUEE-WST) - 7 Product Code - - KANSUEE-WST 8 Nominal Thickness MM ASTM-D 3652 0.6±3.5% 9 Peel with Metal GRAM/CM² ASTM D-3330 3500-4000 10 Temprature - C° 80-100 11 Low Temprature Flexibility - NO crack NO crack 



Additional Information:

  • Delivery Time: READY STOCK

View Complete details

get quote request a call back
  • GREE R9 Pu Foam
  • GREE R9 Pu Foam
  • GREE R9 Pu Foam
GREE R9 Pu Foam

GREE R9 Pu Foam

Rs 350  / PieceGet Best Price

Minimum Order Quantity: 12 Piece

Product Brochure

Packaging Size750 ml
BrandGREE
Model NumberGREE PU FOAM
Packaging TypeBOTTLE
Application IndustryJoint filling, Construction
Surface Of ApplicationCeramic, Plastic, Metal
FormLIQUID
Grade StandardIndustrial
StrengthHigh
Material CompatibilityCeramic
Chemical ResistanceAutomotive Fluids
ABOVE PRICE IS INCLUDING GST18%.
Gree Multi-Purpose PU Foam – R9 Product Description Gree R9 is one component, ready to use multi – purpose polyurethane foam. It is fitted with German engineered plastic adapter head for use with foam gun or straw applicator. It will expand and cure by moisture in the air. Used for wide range of building application like filling gaps or sealing cracks. Has excellent mounting capacities, High thermal and acoustic insulation properties. Product Features & Application Good adhesion to variety of surfaces such as UPVC, Masonry, Brick, block work, glass, steel, aluminum, timber and other substrates except Teflon, PE or PP. • Installing, fixing, insulation of doors & window frames • Filling and sealing of gaps, joints, openings and cavities. • Insulating electrical outlets and water pipes. • Sealing of all openings in roof constructions. • Creation of soundproof screen. • Improving thermal insulation in cooling systems.
Product Properties Base Polyurethane Consistency Stable Foam Curing Moisture – Cure Tack- Free Time (min) 7~15 Cutting Time (min) 30 min (+25°C) Yield (L) 35 Shrink < 1% Post Expansion < 1% Cellular Structure 40 ~ 45 % open cells Specific Gravity (kg/m³) 25 Temperature Resistance -40 °C ~ +90°C Application Temperature Range +5°C ~+35°C Color Champagne Fire Class (Din 4102) B3 Insulation Factor (Mw/m.k) <36 Compressive Strength (kPa) >150 Tensile Strength (kPa) >28 (10%) Adhesive Strength (kPa) >75 Water Absorption 1 % VolumeApplication • Shake the Aerosol can for at least 20 seconds. • Put the adapter on the value. • Moisten surface with a water sprayer prior to application. • Remove pressure from the applicator to stop. • Fill holes and cavities for 50%, as the foam will expand. • Repeat Shaking regularly during application. • If you have to work in layers repeat moistening after each layer. • Fresh foam can be removed using Foam cleaner or acetone. • Cured foam can only be removed mechanically
750 Ml / Can – 12 Cans / Box Shelf Life: 12 Months from date of manufacturing in unopened packaging stored in a cool and dry place at recommended temperatures between +5°C and +25°. Always Keep the can with the value pointed upward 





Additional Information:

  • Delivery Time: READY STOCK
  • Packaging Details: 750 ML PACK

View Complete details

get quote request a call back
  • Fischer Injection Mortar Fis V 360
  • Fischer Injection Mortar Fis V 360
  • Fischer Injection Mortar Fis V 360
Fischer Injection Mortar Fis V 360

Fischer Injection Mortar Fis V 360

Rs 1,156  / PieceGet Best Price

Minimum Order Quantity: 20 Piece

Product Brochure

MaterialAutoclaved Aerated Concrete
Usage/ApplicationConstruction
Packaging Size600 GM(360 ML)
TypePASTE
Coverage AreaAS PER APPLICATION
Thickness110 -150 PAS
CoverageAS PER APPLICATION
StandardISI
Packaging TypePLASTIC CARTRIDGE
Country of OriginMade in India
ABOVE PRICE IS INCLUDING GST 18%.
High performance hybrid mortar in shuttle cartridge, styrene free Colour: grey
Technical Data: Product Data Testing Method Results Stability UV-resistance (sunlight) resistant Temperature resistance 120 °C Water resistance resistant Water absorption after 14 days: 0.8 % Cleaning agents 1 % tenside solution no effects Long-term behaviour (Freezing and thawing resistance) EOTA part 5 approved suitability for outside applications Physical properties Shrinkage < 0.9 % Hardness Shore A after 45 min: 83 Density 1.6 - 1.8 g/cm3 Thermal conductivity 0,73 W/mK Contact resistance 1,8 x 1012 Ωcm Workability features Viscosity (20 °C) Brookfield (Sp.7) 10 U/min 110 – 150 Pas Open time (10 – 20 °C) 5 min Curing time (10 – 20 °C) 60 min Shelf life 18 months

Additional Information:

  • Delivery Time: READY STOCK
  • Packaging Details: 600 GM

View Complete details

get quote request a call back
  • Zorrik 311 Premium Metal Putty
  • Zorrik 311 Premium Metal Putty
  • Zorrik 311 Premium Metal Putty
Zorrik 311 Premium Metal Putty

Zorrik 311 Premium Metal Putty

Rs 3,422  / KgGet Best Price

Minimum Order Quantity: 6 Kg

Product Brochure

Packaging Size1 KG
BrandPidilite
Model NumberZORRIK PREMIUM METAL PUTTY
Packaging TypeDABBA
Application IndustrySealing
Surface Of ApplicationCeramic, INDUSTRIAL
FormPASTE
Grade StandardIndustrial
StrengthHigh
Material CompatibilityMetal
Chemical ResistanceAutomotive Fluids
Country of OriginMade in India
ABOVE PRICE IS INCLUDING GST 18%.
ZORRIK 311 Premium Metal Putty is a two-part Ferro-silicon filled epoxy resin system, engineered to highly machinable and good corrosion resistance to mild chemical attack. Designed to work under service temperature of -30 °C to 120 °C.
Product Features
  • Contains no iron or steel fillers
  • Corrosion is eliminated due to high Ferro-silicon content during service time
  • Epoxy resin base – Excellent adhesion to steel, and cast iron
  • Superior machining finished surface
  • Tolerance- Facilitates fine tolerance limits
  • Excellent resistance to a variety of chemicals
  • Technical Specification
    • Appearance ( Mix): Grey paste
    • Components : Two Component- Mixing
    • Cure : Room temperature
    • Mix Ratio by Volume – Resin : Hardener:: 4:1
    • Mix Ration by Weight- Resin: Hardener:: 7:1
    • Coverage: 575 cm² @ 6 mm thickness per 1 kg kit
    • Operating Temperature : -30 °C to 120 °C
  • Application of Product
    • Shaft: Restoring tolerance to worn shafts
    • Bearing seats and housings
    • Motor end covers
    • Key ways
    • Thinned pipes, tubes sections
    • Engine blocks
    • Pump casings and impeller
    • Rebuilding of water, coal slurry pump casings


Additional Information:

  • Delivery Time: READY STOCK
  • Packaging Details: Shaft: Restoring tolerance to worn shafts,Bearing seats and housings.  Motor end covers  Key ways  Thinned pipes, tubes sections.  Engine blocks  Pump casings and impeller.

View Complete details

get quote request a call back
  • Cvc R7 Turbo Fix Cold Vulcanized Cement
  • Cvc R7 Turbo Fix Cold Vulcanized Cement
  • Cvc R7 Turbo Fix Cold Vulcanized Cement
  • Cvc R7 Turbo Fix Cold Vulcanized Cement
  • Cvc R7 Turbo Fix Cold Vulcanized Cement
Cvc R7 Turbo Fix Cold Vulcanized Cement

Cvc R7 Turbo Fix Cold Vulcanized Cement

Rs 620  / SetGet Best Price

Minimum Order Quantity: 12 Set

Product Brochure

Packaging Size1 Litre
BrandTURBOFIX
Model NumberTURBOFIX CVC R7 & CVC H7
Packaging TypeTin Can
ApplicationCONVEYAR BELT JOINTING ADHESIVE
ColorBROWN
Model Name/ NumberTURBOFIX CVC R7 & CVC H7 1.050ML PACK
Application IndustryJointing
Material CompatibilityRUBBER
Chemical ResistanceWater
Country of OriginMade in India
ABOVE PRICE INVCLUDING GST 18%.
Description: Turbofix COLD VULCANISING CEMENT (CVC–R7) is viscous liquid of brushing viscosity. It is two component room temperature curing chloroprene based rubber adhesive that when catalysed with the appropriate amount of Hardener, yields high strength adhesion when bonding rubber to rubber ,rubber to fabric, rubber to steel, rubber to PVC, urethane, fiberglass, concrete etc. It is formulated after intense R & D efforts to address diverse application needs of the industry. MIXING RATIO : 100 gm Turbofix CVC–R7 and 8 gm Hardener Turbocure CVC-H7. Applications: Add required amount of hardener with adhesive. Mix the solution properly until a uniform coloration occurred. Recommended doses 8 grams of hardener with 100 grams of adhesive. The prepared mixture should be consumed within 4 – 5 hrs to avoid the effect of solvent evaporation and thickening of the mix due to cross linking leading to inferior spreading property. Keep the pot covered whenever not in use. The product is highly sensitive to moisture. CUSTOMER BENEFITS • Higher coverage – Cost Effective • Superior bonding strength – Quality output • More open time – Meets Production cycle requirements. • No settlement – Uniform performance • Does not contain benzene – Saves human life from possibility of cancer SOME APPLICATIONS PROCEDURE 1) Rubber to steel :- Metallic surfaces must be free of oils grease or other contaminants. Rust and mill scale should be removed by sand blasting to NACE#2.A profile of 2-3 mils is preferred. The rubber, if cured should have all mould release agent removed and buffed with 24 grit of stiff bristled wire brush at a speed as not to burn a rubber surface. Apply a first coat to each surface with scrubbing – like motion. Allow this coat to dry for at least 1 hour at 25°C, after the required drying time a second coat is applied to each surface. Let dry until tacky, adhere both surfaces and stitch down or apply pressure. The maximum bond strength will develop to its optimum in 21 days; however initial bond strengths will be sufficiently high after 24 hours and are ready for most services. Doc No.: QC/03 (J) Issue Date 15/09/06 Rev.No. 02 Rev. Date 20/02/2010 Ref. No: QP/03/A-18/17 Page 1 OF 2 TECHNICAL DATA SHEET TURBOFIX COLD VALCANISING CEMENT (CVC- R7) 2) Rubber to Rubber The rubber, if cured in sheet form should be solvent cleaned and buffed as described above before the first coat of adhesive is applied. Allow the first coat to dry for at least 1 hour or longer. After the required drying time a second coat is applied and when still tacky, stitch the two components together or apply pressure. 3) Rubber to other substrates For adhering other elastomeric materials or special environmental conditions, please go for trial to determine the suitability of this product with individual materials and to determine the preferred method of applications. COVERAGE Theoretical coverage : 4 – 5 m2 per liter. PROPERTIES COLD VULCANISING CEMENT NVM Content % 18 – 20.0 % Brookfield Viscosity (at 25 °C) 1100 – 1300 cps PACK SIZES: Available in 1 Litre, 5 Litres and 30 Litres packs STORAGE AND SHELF LIFE Stored in well-sealed containers. Turbofix COLD VULCANISING CEMENT will keep satisfactorily for 12 months from the date of manufacture. Low or high temperature storage should be avoided. Services: For further information on this product together with advice on application please contact Polygel Industries Pvt. Ltd. – Technical Services Department Important Notice: Whilst all reasonable care is taken in the compilation of this data sheet, it is customer’s responsibility to determine the suitability of the product for the desired application. Also the specification parameters represent typical values and variations may be observed with in standard tolerances.

Additional Information:

  • Delivery Time: WITHIN WEEK
  • Packaging Details: 1.0510 LTR.

View Complete details

get quote request a call back
  • Loctite 3900 Conformal Coating 500ml
  • Loctite 3900 Conformal Coating 500ml
  • Loctite 3900 Conformal Coating 500ml
  • Loctite 3900 Conformal Coating 500ml
Loctite 3900 Conformal Coating 500ml

Loctite 3900 Conformal Coating 500ml

Rs 837  / PieceGet Best Price

Minimum Order Quantity: 10 Piece

Product Brochure

Packaging TypeBottle
Packaging Size500 MLPACIK
FinishHigh Gloss
ColorTransparent
BrandLOCTITE
FormSpray
Usage/ApplicationMetal
Flash PointDielectric Constant / Dissipation Factor, IEC 60250:
Grade StandardCONFORMAL COATING
MaterialSPRAY
ABOVE PRICE INCLUDING GST 18%.
LOCTITE 3900 provides the following product characteristics: Technology Acrylic Chemical Type Acrylic resin Appearance (uncured) Transparent, colorless to slightly amber solutionLMS Components One component - requires no mixing Cure Room temperature cure Application Conformal coating Specific Benefit ● High dielectric strength ● Fast drying ● Precision spray nozzle ● Contains no CFC's
LOCTITE 3900 is a clear acrylic formulated without chlorinated solvents or CFC's. The coating is spray-applied and air dries tack-free in five minutes to provide a tough environmental and solvent-resistant coating. The material provides protection of printed circuit boards, electronic components, thick-film circuits and other substrates. This product is typically used in applications with an operating range of -40 °C to +125 °C. TYPICAL PROPERTIES OF UNCURED MATERIAL Specific Gravity @ 25 °C 1.14 Flash Point - See SDS TYPICAL PROPERTIES OF CURED MATERIAL Physical Properties Water Vapor Trans. Rate, ASTM E96, g/(h·m²) 0.325 Shore Hardness, ISO 868, Durometer D 60 Elongation, ISO 527-3, % 1.5 Tensile Strength, ISO 527-3 N/mm² 5.9 (psi) (850) Tensile Modulus, ISO 527-3 N/mm² 586 (psi) (85,000) Electrical Properties Volume Resistivity, IEC 60093, Ω·cm 7.21×1015 Surface Resistivity, IEC 60093, Ω 1.88×1017 Dielectric Breakdown Strength, IEC 60243-1, kV/mm 65 Dielectric Constant / Dissipation Factor, IEC 60250: 100-Hz 3.37 / 0.062 1-kHz 3.07 / 0.052 GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Safety Data Sheet (SDS).Directions for use: 1. Surface should be free of flux, grease, ionic residue or any other contaminates. Mask board if required. 2. Shake can thoroughly before use. 3. Spray board 15 to 20 cm from surface with even motion. 4. Rotate board and repeat application 2-3 times for best coverage. 5. Application with PCB in horizontal position recommended for even coating. 6. A coating of 0.05 to 0.07 mm will air dry tack-free within 5 minutes @ 22 °C and 40 to 60 %RH. Full cure requires 24 hours @ 22 °C. 7. Cured coatings may be removed by soaking in acetone. Component replacement may be accomplished by localized desoldering/soldering through the coating and reapplication. Loctite Material SpecificationLMS LMS dated April-26, 2001. Test reports for each batch are available for the indicated properties. LMS test reports include selected QC test parameters considered appropriate to specifications for customer use. Additionally, comprehensive controls are in place to assure product quality and consistency. Special customer specification requirements may be coordinated through Henkel Quality. Storage Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or Customer Service Representative 

Additional Information:

  • Delivery Time: WITHIN THREE TO FOUR DAYS
  • Packaging Details: 500 ML

View Complete details

get quote request a call back
  • Maax Quick  Stain Lifter
  • Maax Quick  Stain Lifter
  • Maax Quick  Stain Lifter
Maax Quick  Stain Lifter

Maax Quick Stain Lifter

Rs 295  / PieceGet Best Price

Minimum Order Quantity: 32 Piece

Usage/ApplicationGREASE OIL REMOVER
BrandINDIAN
TypeDetergents
Packaging TypeBottle
Physical StateLiquid
Packaging SizeBOTTEL 500 ML
FormLiquid
ColorWHITE
Weight500 ML
MaterialSPRAY BOTTLE
Above price is including gst 18%
maax? ? ? Quick stain lifter heavy duty oil and grease stain remover features & applications ? ? ? Removes oil, grease and most food stains and spots ? ? ? Fast action ? ? ? Leaves no ring ? ? ? Easy to use ? ? ? Specially designed cleaning stains on shirts,t-shirts, trousers,blouses,gloves,socks,uniforms,car upholstery,carpeting,wall papers,slipcovers,hats, knitted ,woven and denim garments ? ? ? Test color fastness of the fabric material to be cleaned by testing in hidden area and do not use on plastics, rubberised material and leather. Method of use ? ? ? Shake well before use, till the movement of the ball is audible ? ? ? Remove cap, hold can 4-5 inches from stain and spray on stain. ? ? ? Allow to dry 5-10 minutes ? ? ? When completely dry brush it off or vacuum off and smile. ? ? ? Repeat cleaning operation if required specifications property maax– quick stain lifter colour white specific gravity (g/cc) 0. 98± 0. 02 soluble in water in soluble shelf life 18 months packing 400 ml

Additional Information:

  • Delivery Time: IMMEDIATE
  • Packaging Details: 500 ML

View Complete details

get quote request a call back
  • Molykote Tp 42 Paste
  • Molykote Tp 42 Paste
Molykote Tp 42 Paste

Molykote Tp 42 Paste

Rs 3,658  / KgGet Best Price

Minimum Order Quantity: 1 Kg

Product Brochure

Packaging Size>1000gm
BrandDUPONT
FormGREASE
ApplicationLight-colored adhesive grease-paste with solid lubricants for metallic friction combinations
Base Oil Visc @ CKesternich method - flow pressure at -20 DegreeC
Base Oil ViscosityDensity at 20 DegreeC
ChemistryWater resistance, static
ColorLight beige
CompositionTorque after 20 minutes running time
Country of OriginMade in India
ABOVE PRICE IS INCLUDING GST 18%
Light-colored adhesive grease-paste with solid lubricants for metallic friction combinations
Features • High load-carrying capacity • Particularly adhesive • Particularly resistant to washout by water and metal machining emulsions • Prevents stick-slip • Good corrosion protection • Excellent protection against galling Composition • Mineral oil • Synthetic oil • Lithium soap • Solid lubricants • Adhesion improver Applications Sliding surfaces exposed to high pressure loadings and subject to the influence of water of metal machining emulsions. Recommended and successfully used by leading clampingelement manufacturers, especially for chucks on metal processing machines.
How to use The sliding surfaces should be cleaned. The paste should then be applied with a suitable brush, rag or grease gun. It should not be mixed with greases or oils. Handling precautions PRODUCT SAFETY INFORMATION REQUIRED FOR SAFE USE IS NOT INCLUDED IN THIS DOCUMENT. BEFORE HANDLING, READ SAFETY DATA SHEETS AND CONTAINER LABELS FOR SAFE USE, PHYSICAL AND HEALTH HAZARD INFORMATION. Usable life and storage When stored at or below 20°C in the original unopened containers, this product has a usable life of 60 months from the date of production.
Typical properties Specification writers: These values are not intended for use in preparing specifications. Please contact your local MOLYKOTE® sales representative prior to writing specifications on this product. Standard(1) Test Unit Result Color Light beige Penetration, density, viscosity ISO 2137 Unworked penetration mm/10 265-300 ISO 2811 Density at 20°C g/ml 1.19 Temperature Service temperature(2) °C -25 to +250 ISO 2176 Drop point °C 125 ASTM D1478-80 Low-temperature torque test at -20°C Initial break-away torque Nm 224x10-3 Torque after 20 minutes running time Nm 59x10-3 DIN 51 805 Kesternich method - flow pressure at -20°C mbar 740 Load-carrying capacity, wear protection, service life Four-ball tester (VKA) DIN 51 350 pt.4 Weld load N 3,000 DIN 51 350 pt.5 Wear under 800 N load mm 0.9 Almen-Wieland machine OK load N 20,000 Friction force N 1,710 Coefficient of friction Press-fit test µ = 0.09 Resistance DIN 51 807 pt.1 Water resistance, static 2-90 (1)ASTM: American Society for Testing and Materials. ISO: International Standardization Organization. DIN: Deutsche Industrie Norm. (2) Thermal stability of solid lubricant.Typical properties (continued) Standard(1) Test Unit Result Corrosion protection DIN 51 802 SKF-Emcor method Degree of corrosion 0-1 Oil separation - evaporation DIN 51 817 Oil separation, standard test % 1.5 (1)ASTM: American Society for Testing and Materials. ISO: International Standardization Organization. DIN: Deutsche Industrie Norm.
 

Additional Information:

  • Delivery Time: WITHIN THREE TO FOUR DAYS
  • Packaging Details: 1 KG

View Complete details

get quote request a call back
  • GREE WATERPROOF PATCH & SEAL STOP  LEAK
  • GREE WATERPROOF PATCH & SEAL STOP  LEAK
  • GREE WATERPROOF PATCH & SEAL STOP  LEAK
GREE WATERPROOF PATCH & SEAL STOP  LEAK

GREE WATERPROOF PATCH & SEAL STOP LEAK

Rs 295  / PieceGet Best Price

Minimum Order Quantity: 12 Piece

BrandGREE
Model NumberGREE STOP LEAK
Packaging TypeBOTTLE
Application IndustryJointing
Surface Of ApplicationCeramic
FormLIQUID
Grade StandardIndustrial
StrengthHigh
Material CompatibilityMetal
Chemical ResistanceAutomotive Fluids
Country of OriginMade in India
ABOVE PRICE I INCLUDING GST 18% 

Additional Information:

  • Delivery Time: READY STOCK

View Complete details

get quote request a call back
  • Maax TEF Lube Dry Dry Boned PTFE Spray
  • Maax TEF Lube Dry Dry Boned PTFE Spray
  • Maax TEF Lube Dry Dry Boned PTFE Spray
Maax TEF Lube Dry Dry Boned PTFE Spray

Maax TEF Lube Dry Dry Boned PTFE Spray

Rs 860  / PieceGet Best Price

Minimum Order Quantity: 32 Piece

Product Brochure

Unit Pack Size500 ML
Model GradeMAAX TEFLUBE DRY
Usage/ApplicationIndustrial
FormLIQUID
GradeH1
ColorDRY WHITE
PropellantPTFE
Surface FinishGOOD
Eco FriendlyNO
Packaging TypeCAN
ABOVE PRICE IS INCLUDING GST 18% 
Hi performance PTFE Dry Lube Spray PROPERTIES   Excellent penetration provides complete lubrication   Soft consistency  Low starting resistance  Good adhesion, silencing and water resistance  Protects against rust and corrosion  Excellent cold, hot and salt water resistance  Long life and efficiency   Prevents sticking of dirt, dust and other stains on coated surfaces  Operating temperature up to 250°C  Plastic & Rubber safe APPLICATIONS  Designed for lubricating and silencing noise from door hinges, seat adjustment mechanisms, joints, shift linkage, rubber mountings, chains, window channel doors, emergency brake, pedal, threaded parts, etc., SPECIFICATIONS Property MAAX TEF LUBE Colour Dry -White Solid Lubricant PTFE Density@ 25°C 0.85 Film Type Wet Operating temp in °C min + 250°C Packing 500 ml spray or 1 ltr /5 ltr

Additional Information:

  • Delivery Time: WITHIN WEEK
  • Packaging Details: 500 ML /1 LTR /5 LTR

View Complete details

get quote request a call back
  • GREE ACRALIC FOAM TAPE
  • GREE ACRALIC FOAM TAPE
  • GREE ACRALIC FOAM TAPE
GREE ACRALIC FOAM TAPE

GREE ACRALIC FOAM TAPE

Rs 90  / PieceGet Best Price

Minimum Order Quantity: 50 Piece

Product Brochure

Tape Width0-20 mm
Tape Length10 m
Backing MaterialGUM
ColorCLEAR
BrandGREE
Usage/FeatureAutomotive, Electronics, Advertisements & Signage, Building & Constructions, Solar Panels, Elevators
MOQ200
Tape TypeAdhesive
Total Thickness10MM
ElongationGOOD
ABOVE PRICE IS INCLUDING GST 18%
Product Description R- 927 is a grey double sided acrylic foam tape. Product Structure Grey Acrylic Foam Product Features & Application • Super adhesion power bonds to ceramic, marble, wood, steel, glass, plastic, leather, metal etc. • Great resistance to aging including high and low temperature, UV Light, Moisture and Solvents. • Used in across industries such as Automotive, Electronics, Advertisements & Signage, Building & Constructions, Solar Panels, Elevators, Home improvements, Glass & Façade etc. Product Properties Item Unit Value Standard Total Thickness Mm 1.20 ±0.10 GB/T7125-2014 Property Adhesion to Steel 180° Peel 20min N/24mm ≥25 GB/T2792-2014 72 H ≥50 Static Shearing 24mm X 24mm 23°C, 1000g Min ≥1440 GB/T4851-2014 80°C, 500g ≥1440 Dynamic Shearing 24mm X 24mm 20min ≥300 GB/T33332-2016 72 H ≥400 Loop Tack 24mm X 24mm ≥30 GB/T31125-2014 Temperature Resistance Short Term °C (-20) - 140 - Long Term (-20) - 80 Shelf Life Typically within 12 months of Gree shipment in original packaging – To be stored in 23-35°C and 10-70% relative humidity conditions. Application Technique Clean the surface well with dry cloth. Ensure surface is free from grease, oil, stains and dust. Apply pressure after applying the tape to get better bonding




Additional Information:

  • Delivery Time: READY STOCK
  • Packaging Details: 8MM/10MM/12MM

View Complete details

get quote request a call back
  • GREE STICKER REMOVER ADHESIVE
  • GREE STICKER REMOVER ADHESIVE
  • GREE STICKER REMOVER ADHESIVE
GREE STICKER REMOVER ADHESIVE

GREE STICKER REMOVER ADHESIVE

Rs 220  / PieceGet Best Price

Minimum Order Quantity: 12 Piece

Product Brochure

Packaging Size500 ml
MaterialPaper
BrandGREE STICKER ADHESIVE REMOVER
Pack TypeBOTTLE
ColorCLEAR
Grade StandardTechnical Grade
Packaging TypeBOTTLE
AppearanceLIQUID
OdourODOUR LESS
Packet Contain400 ML
SolubilityHEAVY
Chemical ResistanceAutomotive Fluids
Country of OriginMade in India
ABOVE PRICE IS INCLUDING GST 18%.
S -126 Product Description Gree sticker remover is composed of aerosol can, aerosol valve, paint solution and propellant. This product uses mild remove formula, can effectively dissolve the surface colloid of the removed object, do not corrode the surface of the object, spray and wipe just once, easy to remove. Product Features & Application • Easy to remove • Car care and household • Not to hurt the object • Environmental protection formulaIt is widely used in the repair of templates, aluminium plastic panels, metal, ceramics, glass, automotive paint and some rubber, such as transparent adhesive removal. Instruction & Usage ●Shake well before use, keep the bottle body upright and spray evenly at 15cm from the surface. ●The cleaning part should be sprayed to cover when the glue is removed, and the size and thickness of the residual gum will determine the amount of the product. ●After spraying the product, wait for a moment, so that the liquid is fully immersed in the colloid and then combined with cotton scraper or suitable tools to achieve the best adhesive remover effect. ●It dissolves the glue, the barrier materials such as paper and plastic film on the surface of the film should be cleaned out first, so as to prevent the liquid from contacting the colloid to achieve the effect of removing glue. ●When the remaining small amount of liquid can not be ejected, please rotate the nozzle 180° and spray again.Ending Work If not finished, the remaining materials should be kept at room temperature to avoid exposure to fire sources. Technical Specification Parameter Unit At 25°C and 60% relative humidity Liquid appearance --- Colorless transparent liquid Smell --- Comply with the regulations Rate of spray % ≥97 Internal pressure, 50°C MPa ≤1.0 Density ( 20°C) g/cm³ 0.73-0.83Emergency Treatment ●When sticking to the skin, wash with soap and water. If you feel uncomfortable, please go to the hospital immediately. ●In case of accidental contact with the eyes, lift the eyelid and rinse immediately with plenty of water or saline solution, seek medical advice immediately. ●In case of accidental ingestion, drink a moderate amount of warm water and induce vomiting. Seek medical advice immediately. Attention ●Keep away from children, please work in the air. If swallowed, you should immediately cause vomiting and seek medical advice. ●Spray must be kept in aerosol cans are vertical and horizontal angle of no less than 45 °. ●Flammable, pressure vessel, do not use near fire source. ●The weight changes over time, which is normal, and the attrition rate is less than 2%/ year.



Additional Information:

  • Delivery Time: READY STOCK
  • Packaging Details: 400 ML

View Complete details

get quote request a call back
  • PIDITHERM AD 4050 THERMAL CONDUCTIVE ADHESIVE
  • PIDITHERM AD 4050 THERMAL CONDUCTIVE ADHESIVE
  • PIDITHERM AD 4050 THERMAL CONDUCTIVE ADHESIVE
PIDITHERM AD 4050 THERMAL CONDUCTIVE ADHESIVE

PIDITHERM AD 4050 THERMAL CONDUCTIVE ADHESIVE

Rs 755  / NumberGet Best Price

Minimum Order Quantity: 24 Number

Product Brochure

Packaging Size300 ml
Packaging TypeCartridge
Application IndustryAutomotive, Medical, Telecom
Surface Of ApplicationCeramic, Plastic, Metal
FormPASTE
Grade StandardIndustrial
StrengthHigh
Material CompatibilityPlastic, Metal, Ceramic
Chemical TypeCONDUTIVE ADHESIVE
Chemical ResistanceAutomotive Fluids
Thickness1.65 +-0.1
ColorWHITE
AppearanceSemi flowable paste
Fixture Time5-10
Curing Time12 HOUR
Cure Mechanism60
ABOVE PRICE IS INCLUDING GST 18%
PRODUCT DESCRIPTION: PIDITHERM AD 4050 is a one-part, white, semi flowable, thermally conductive silicone adhesive with good adhesion designed for effective heat dissipation from electronic modules. PIDITHERM AD 4050 cures at room temperature under the action of atmospheric moisture to give a permanently flexible thermally conductive silicone rubber. FEATURES AND BENEFITS: Unique Features: • One part, room temperature cure adhesive • Fast cure with short tack free time • Good thermal conductivity and excellent electrical insulation • Good flame resistance APPLICATION AREAS: • Bonding/fixing in power module assembly • Electronic parts bonding • LED lighting product assembly • Automotive part assembly TYPICAL PROPERTIES Feature Unit Value Appearance Semi flowable paste Colour White Skin over time @ 30oC Minutes 5-10 Full Cure time ( min 3 mm) @ 30oC Hours 12 Density gm/cc 1.65 +- 0.1 Hardness Shore A 60 Thermal Conductivity W/mK 1.2 Dielectric Strength kV/mm >18 Temperature stability range oC -40 to 200 APPLICATION PROCESS: • The substrate areas that will be in contact with the adhesive must be clean, dry and free of all loose material, dust, dirt, rust, oil and other contaminants. Substrates should be cleaned with a solvent and a clean, lint-free, cotton cloth. Remove residual solvent before it evaporates with a fresh clean dry cloth • Assemble properly the cartridge in the manual or pneumatic dispensing gun • Cut the cartridge with the help of a cutter or knife to get the required bead size • Immediately apply the material with a continuous uniform pressure quickly on the surfaces • Assemble parts immediately with the skin over time period p STORAGE AND HANDLING: PIDITHERM AD 4050 has life of at least 9 months when stored in a cool (below 25oC), dry place in moisture-tight original container. The “Best use before date” of each batch is shown on product label. If the material is kept beyond the recommended shelf life, it is not necessarily unusable, but a quality control should be performed on the properties relevant to the application. 

Additional Information:

  • Delivery Time: READY STOCK
  • Packaging Details: 300 ML

View Complete details

get quote request a call back
  • KANSUEE ANTI SKID TAPE
  • KANSUEE ANTI SKID TAPE
  • KANSUEE ANTI SKID TAPE
KANSUEE ANTI SKID TAPE

KANSUEE ANTI SKID TAPE

Rs 413  / RollGet Best Price

Minimum Order Quantity: 10 Roll

Product Brochure

Tape Width41-60 mm
Backing MaterialABRASIVE GRIT
ColorYELLOW BLACK
BrandKANSUEE
Usage/FeatureAnti slip for any direction,wet or dry,cuts risk of slips or falls. (2) Economical ,durable, resist
MOQ10
Tape TypeAdhesive
Total Thickness2 MM
ElongationGOOD
ABOVE PRICE IS INCLUDING GST 18%.




Additional Information:

  • Delivery Time: READY STOCK
  • Packaging Details: 48MM*5MTR

View Complete details

get quote request a call back

EXPLORE MORE CATEGORIES