Lube Adhesive & Engineering Co.

ABOVE PRICE IS INCLUDING OF 18% GST

Product Description The Tekbond MS HYBRID It is a one-component adhesive based on hybrid silicone polymer, which can be cured by reacting with moisture in the air and gradually form a high-strength elastomer. It is eco-friendly product, does not contain isocyanates, tin and plasticizer. It has good durability, non-corrosive, UV resistance, water resistance and adheres to a wide range of materials. It shows good mold resistance when be used in the kitchen, bathroom and other areas. It is suit for both interior and exterior. Due to its elasticity and its high adhesion power in several types of materials, the product seals in a differentiated manner with high performance, and can be used in several segments, such as industry, civil construction, metallurgy, automotive, among others. Physical Properties (Visual) appearance: Fine, uniform paste Density at 25°C: 1.64 ± 0.10 g/mL Tack Free, min: ≤ 30 Sagging, mm: ≤ 1 Curing Depth, mm 24h: ≥ 2.0 Curing Depth, mm 7d: ≥ 5.0 Hardness shore A 7d: 35 - 45 Elongation at break, % 7d: ≥ 400 Tensile Strength, MPa 7d: ≥ 1.0 Storage life at 20°C: 12 months Instructions for use and handling 1. The application surfaces must be cleaned with alcohol or acetone, and shall be dry and firm. Do not use kerosene or gasoline to clean surfaces. 2. If needed, apply crepe tape to protect areas where the product is not desired. 3. Cut the tip of the cartridge and cut the applicator nozzle at a 45° angle in the desired size and thickness. Screw the nozzle into the applicator cartridge and place it on the applicator gun. 4. Apply the silicone on the desired area and do the finishing. 5. IMPORTANT: immediately after applying the silicone, remove the crepe tape before the adhesive forms the film.
6. After use, hold the applicator nozzle in the cartridge and leave a small amount of product above the nozzle to form a cap. When reusing, remove the cap. After opened, reuse the product within two weeks. 7. If the parts are heavy, during the gluing process, we advise the placement of clips or hooks so that there is no movement of the part to be glued until the adhesive is completely dry. 8. The total cure is from 24 hours to 48 hours depending on the weather, amount of adhesive and weight of the parts to be glued. Restrictions on use The Tekbond MS HYBRID is not indicated for the following situations: 1. For all surfaces that remove oil, plasticizers or solvents, such as wood immersed in oil and wet surfaces. 2. For a substrate with a surface temperature above 50??? or apply at temperatures below 5??? 3. For situations such as immersion in water for a long period of time. 4. For surfaces that have direct contact with food. 5. It cannot be used as a structural adhesive. Available packages Colors: White, Grey. Packages: 280ML cartridges. Storage Keep the product in a closed container and store it in a cool place at 5 to 27ºC, away from direct sunlight, excessive heat, sparks and flames. Keep it out of the reach of children and pets. To prevent contamination of unused product, do not return any leftover material in its original packaging. For further information and safe handling of this product, please refer to the Safety Data Sheet (SDS).

Additional Information:

• Delivery Time: AVILABLE
• Packaging Details: 280 ML

ABOVE PRICE IS INCLUDING GST 18%.
DOWSIL™ 733 Glass & Metal Sealant®™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow DOWSIL™ 733 Glass & Metal Sealant Page 1 of 4 © 2017–2021 The Dow Chemical Company. All rights reserved. Form No. 95-1071-01-0421 S2D Typical Properties (Cont.)Test Property Unit Result Physical Properties – As Cured 2 Days at 25°C (77°F) and 50% RH Adhesion, 180° Peel Strength Stainless Steel pli 20 Matte Finish Steel pli 20 Aluminum pli 21 Description DOWSIL™ 733 Glass & Metal Sealant is a paste-like, one-component material that cures to a tough, rubbery solid upon exposure to moisture in the air. Because it does not flow, this sealant can be applied overhead or on sidewall joints and surfaces without sagging, slumping or running off. DOWSIL™ 733 Glass & Metal Sealant is specially formulated to provide good adhesion to various substrates. Listings/ Specifications  Recognized under UL 94 HB Complies with FDA.  Regulation 21 CFR 177.2600 for incidental contact with food. How to Use Estimating For estimating sealant requirements, multiply gallons by 128 fluid ounces and divide by the cartridge size. Example: 11 gallons required x 128 fluid ounces = 1408 divided by a 10.1 fluid ounce cartridge = 139 cartridges required. Application DOWSIL™ 733 Glass & Metal Sealant is supplied in ready-to-use form. It extrudes readily from its container under pressure. The paste like consistency makes it easy to work; a spatula or paddle can be used to tool the surface. Bonding Thoroughly clean and degrease metal and plastic surfaces using a DOWSIL™ OS (ozonesafe) fluid or other suitable solvent. Rubber surfaces should be roughened with sandpaper, then wiped with acetone. Follow precautions given on the solvent container label. Apply DOWSIL™ 733 Glass & Metal Sealant to the prepared surface in a uniform thickness. Then, let the unit stand undisturbed at room temperature to cure. Sealing The use of DOWSIL™ 733 Glass & Metal Sealant in sealing applications follows approximately the same step-by-step procedures outlined for bonding applications. After preparing the surfaces and priming where required, the sealant is applied by forcing it into the joint or seam to obtain full contact between the sealant and the surface. ®™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow DOWSIL™ 733 Glass & Metal Sealant Page 3 of 4 © 2017–2021 The Dow Chemical Company. All rights reserved. Form No. 95-1071-01-0421 S2D How to Use (Cont.) Tack-free Time Cure progresses inward from the surface. At conditions of at least 25°C (77°F) and 50 percent relative humidity, a tack-free skin forms within 10 to 15 minutes. Tooling should be completed within 5 to 10 minutes of application. Alternate periods of application and tooling may be required. If masking tape is used to mask an area, it must be removed before the tack-free skin forms. Cure Time Cure time is affected by relative humidity, degree of confinement and cross-sectional thickness of the sealant. Sections up to 1/8 inch thick become rubbery solids in about 24 hours at room temperature and 50 percent relative humidity. Less humidity increases cure time slightly. In applications where DOWSIL™ 733 Glass & Metal Sealant may be partially or totally confined during cure, the time required for proper cure is generally lengthened by the degree of confinement. It is possible that with absolute confinement, cure will not be completed. Every application involving confinement during cure should be thoroughly tested before use. 

Additional Information:

• Delivery Time: READY STOCK
• Packaging Details: 310 GM

ABOVE PRICE IS INCLUDING GST 18%.
SECTION 1. IDENTIFICATION Product name : DOW CORNING(R) 732 MULTI -PURPOSE SEALANT CLEAR Product code : 000000000001890573 Manufacturer or supplier's details Company name of supplier : Dow Corning Corporation Address : South Saginaw Road Midland Michigan 48686 Telephone : (989) 496-6000 Emergency telephone : 24 Hour Emergency Telephone : (989) 496-5900 CHEMTREC : (800) 424-9300 Recommended use of the chemical and restrictions on use Recommended use : Adhesive, binding agents SECTION 2. HAZARDS IDENTIFICATION GHS classification in accordance with 29 CFR 1910.1200 Not a hazardous substance or mixture. GHS label elements Not a hazardous substance or mixture. Precautionary Statements : Prevention: P271 Use only outdoors or in a well-ventilated area. Other hazards None known. SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS Substance / Mixture : Mixture Chemical nature : Silicone elastomer Hazardous ingredients Chemical name CAS-No. Concentration (% w/w) Silicon dioxide 7631-86-9 >= 7 -<= 12 SECTION 4. FIRST AID MEASURES If inhaled : If inhaled, remove to fresh air.
Version 2.3 Revision Date: 03/13/2017 SDS Number: 809362-00009 Date of last issue: 01/12/2017 Date of first issue: 11/21/2014 2 / 12 Get medical attention if symptoms occur. In case of skin contact : Wash with water and soap as a precaution. Get medical attention if symptoms occur. In case of eye contact : Flush eyes with water as a precaution. Get medical attention if irritation develops and persists. If swallowed : If swallowed, DO NOT induce vomiting. Get medical attention if symptoms occur. Rinse mouth thoroughly with water. Most important symptoms and effects, both acute and delayed : None known. Protection of first-aiders : No special precautions are necessary for first aid responders. Notes to physician : Treat symptomatically and supportively. SECTION 5. FIRE-FIGHTING MEASURES Suitable extinguishing media : Water spray Alcohol-resistant foam Carbon dioxide (CO2) Dry chemical Unsuitable extinguishing media : None known. Specific hazards during fire fighting : Exposure to combustion products may be a hazard to health. Hazardous combustion products : Carbon oxides Silicon oxides Formaldehyde Specific extinguishing methods : Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. Use water spray to cool unopened containers. Remove undamaged containers from fire area if it is safe to do so. Evacuate area. Special protective equipment for fire-fighters : Wear self-contained breathing apparatus for firefighting if necessary. Use personal protective equipment. SECTION 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emer- : Follow safe handling advice and personal protective equipment recommendations.SAFETY DATA SHEET DOW CORNING(R) 732 MULTI -PURPOSE SEALANT CLEAR Version 2.3 Revision Date: 03/13/2017 SDS Number: 809362-00009 Date of last issue: 01/12/2017 Date of first issue: 11/21/2014 3 / 12 gency procedures Environmental precautions : Discharge into the environment must be avoided. Prevent further leakage or spillage if safe to do so. Retain and dispose of contaminated wash water. Local authorities should be advised if significant spillages cannot be contained. Methods and materials for containment and cleaning up : Soak up with inert absorbent material. For large spills, provide diking or other appropriate containment to keep material from spreading. If diked material can be pumped, store recovered material in appropriate container. Clean up remaining materials from spill with suitable absorbent. Local or national regulations may apply to releases and disposal of this material, as well as those materials and items employed in the cleanup of releases. You will need to determine which regulations are applicable.  

Additional Information:

• Delivery Time: READY STOCK
• Packaging Details: 90ML/132ML 310 ML

GST 18% EXTRAWEATHER PROOF (WS 789)

 

WEATHER PROOF SILICONE SEALANT (WS789)

KINGSTON WS 789 IS THE BEST ONE PART, MID MODULUS, RTV NEUTRAL CURE SILICONE RUBBER SEALANT THAT OFFERS EXCELLENT ADHESSION & WEATHERPROOF PERFORMANCE IN MULTI PURPOSE.

 

USED ON BONDING, ASSEMBLY, SEALING & REPAIR FOR GLASS, COATED GLASS, ALUMINIUM PRODUCTS & VARIOUS MATERIAL JOINTS OR SEAMS

 

MAIN CHARACTERSITICS

* Neutral Cure Versatile Sealant

* High Adhesion & Cohesion

* High UV Resistance

* Long Life & Flexible

* Use for ACP & Exterior Glazing

* Suitable for all Weather Conditions 

 

PROPERTY - VALUE

Curing System - Moisture Cure

Tooling Time - Approx 25-30 min

Temperature Resistance  - (-50°C to + 100°C)

Packing/ Net Content - 25PCS/300ml & 20PCS/590ml

 

WEATHER PROOF SILICONE SEALANT (WS789)

 

COLORS                 : BLACK / WHITE / CLEAR Other Colors on Demand.

AVAILABLE            : 300ml & 590ml 

Additional Information:

• Delivery Time: WITHIN WEEK
• Packaging Details: 300 ML & 590 ML

Fasto S860 is a one part, all weather, neutral cure, non- corrosive RTV Silicone sealant. Being non-corrosive, it does not corrode metal and protect surfaces. It has good resistance to weathering, UV Radiation, moisture, ozone, air borne pollutants, temperature extremes, cleaning detergents, etc. It can be used for sealing, bonding and glazing applications. It is suitable for electrical, mechanical, automobile and construction applications.   TYPICAL APPLICATIONS  Fasto S860 is suitable for bonding and sealing various substrates. Typical applications are air conditioning ducts, expansion joints, ACP sheets, bus body, street lights, signing boards, solar panels, insulators, JBs and many more electrical & mechanical equipment and machines.  It is suitable for bonding & sealing steel, aluminum, composites, ceramics, glass, plastics, rubber, concrete, etc. 
PROPERTIES OF UNCURED MATERIAL    Value Chemical type     RTV Silicone Appearance     Clear, Specific Specific Gravity (g/ml)   1.02 Ultimate Tensile Strength (MPa)1  2.4 Elongation (%)1    350  Operating Temperature  Range (Dry Service, °C)   -24 to 150 Skin over time (mins)*   15 -25 Tack Free time (mins)*   25 - 35  Full Cure time (hrs)*   24  Hardness (Shore A)   25 Shelf life (months)   12 
Hot strength  Fasto S860 is suitable for use at temperatures up to 150°C.  At 130°C the bond strength will be ~65% of the strength of at  21°C.  Heat ageing  Fasto S860 retains over 96% mass and hardness when heated to 150°C for 10 days then cooled and tested at 23°C.  DIRECTIONS FOR USE  Remove all the rust, scale, dirt, dust, grease, oil, release agents, or other contaminants from the surfaces to be bond or seal. Surfaces can also be cleaned using suitable Fasto cleaner. Apply Fasto S860 with suitable dispensing equipment. Assemble the surfaces immediately in order to avoid skin over.   Apply S860 in sufficient quantity and wipe out the excessive quantity. For construction joints, before applying Fasto S860, clean the surface and ensure that surfaces to be seal should be free from oil, dirt & other contaminants and should be sound. For sealing large joints, use backer rod or bond breaker tape. Also use masking tape to ensure aesthetically clean & neat joints. Always remove masking tape after tooling and before skinning of sealant. LIMITATIONS Fasto S860 should not be used •When surface temperatures exceed 50°C (122°F)  •On surfaces that are continuously immersed in water  • On building materials that bleed oils, plasticizers or solvents, green or partially vulcanized rubber gaskets or tapes  • On frost-laden or wet surfaces .• In totally confined joints (the sealant requires atmospheric moisture for cure)  • If the sealant is intended to be painted (paints do not typically adhere to most silicone sealants)   GENERAL INFORMATION  SAFETY PRECAUTIONS Avoid breathing of vapors. Forced local exhaust is recommended to effectively minimize exposure. NIOSH approved, organic vapor respirators and forced exhaust are recommended in confined areas, or when conditions (such as sanding, etc) may cause high vapor concentrations.   For safe handling of this product consult the Material Safety Data Sheet.  Storage Optimal storage conditions are between 13°C and 25°C. Storage outside this temperature range can adversely affect product properties and may affect the stated shelf life.  Packaging 280 ml cartridge, 20 kg pail, 200 ltr drum

Additional Information:

• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 260 MLPACK