Lube Adhesive & Engineering Co.

ABOVE PRICE IS INCLUDING GST 18%
PRODUCT DESCRIPTION ELASTOSEAL is a single component, ready-to-use elastomeric rubber sealant formulated for superior weather proofing and sealing of various construction joints. The material cures rapidly to a tough, fullbodied, elastic, waterproof seal that maintain its joint movement capability and adhesion for many years. CHARACTERISTICS Its advanced formulation is highly resistant to UV rays, temperature changes and cures to a paintable surface. It works on wet roofs and other surfaces that are not permanently submerged underwater. AREAS OF APPLICATION - Seal holes, gaps and joints in roofs, gutters, flashing, downspouts and drain pipes. - Seals cracks and mating points of concrete and other construction materials needing a flexible seal. - Seals perimeters, gaps, and joints between metal, glass and concrete.
TECHNICAL DATA Table 1: Physical Properties: UNCURED STATE Parameters Results Color Gray Slump Nil Solid Content 76-78% by wt Consistency Thixotropic; easy to apply Homogeneity No seediness; no lumps Specific Gravity @26°C 1.29-1.30 Tack Free Time 8- 21 minutes (17 minutes on the average) Cure Thru Time 15-17 days Shelf life 18 months Table 2: Physical Properties: CURED STATEParameters Results Hardness, Shore A 48 minimum Adhesive Strength (stainless steel dolly in GI sheet) 100-200 psi INSTRUCTION FOR USESurface Preparation. Surfaces must be clean and free from oil, grease and loose particles. Roughen or wire brush smooth or coated surfaces to ensure good adhesion. Method. Using a spatula, apply continuous deep into gap or hole to fill completely. Sealant should ideally overlap repaired and sealed surfaces. Any excess sealant need to be level-off with a trowel or spatula. Cleaning. Wipe all excess materials. Clean used spatulas with thinner. Health and Safety Precautions CAUTION: Combustible. Use only with adequate ventilation. Use gloves. Keep away from source of ignition-no smoking. If contact with skin, wash immediately with soap and water. In case of contact with eyes, rinse immediately with water. If irritation persists, seek medical attention. KEEP OUT OF REACH OF CHILDREN. Any wet or partially wet sealant can be removed by scrapping and use of solvent. Dried sealant is best removed with a scraper or by sanding. OTHERS PACKAGING ELASTOSEAL is available in Can - 385ml (500g) Pouch - 65ml (85g) WARRANTY RCI warrants its products to be free from defects in material and workmanship. RCI’s sole obligation and Buyer’s exclusive remedy in connection with the products shall be limited, at RCI’s option, to either replacement of products not conforming to this Warranty or credit to Buyer’s account in the invoiced amount of the nonconforming products. Any claim under this Warranty must be made by Buyer to RCI in writing within five (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the applicableshelf life, or one year from the delivery date,whichever is earlier. Buyer’s failure to notify RCI of such nonconformance as required herein shall bar Buyer from recovery under this Warranty

Additional Information:

• Delivery Time: WITHIN 2 DAYS
• Packaging Details: 85 GM/250G/500GM/1 KG /345GM

Dow Corning® 791 SiliconeWeatherproofing SealantFEATURES & BENEFITS Ideal for expansion, connection, perimeter and other movement joints Neutral cure – suitable for use on coated glass, galvanized steel, masonry and other porous and non-porous substrates Extension/compression movement capability of up to ±50 percent of the original joint width Excellent weatherability, virtually unaffected by sunlight, rain, snow, ozone Excellent unprimed adhesion to a wide variety of construction materials and building components Ease of application – ready to use as supplied Excellent rheology, low string upon gunningCOMPOSITION One-part, neutral-cure, RTV silicone sealant
Neutral, one-part silicone sealantAPPLICATIONS Dow Corning® 791 Silicone Weatherproofing Sealant is a specified, premium performance weather sealing product specifically designed for general glazing and weather sealing in curtain wall and building facades.TYPICAL PROPERTIESSpecification Writers: These values are not intended for use in preparing specifications. Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product.Test1PropertyUnitResultUncured – As Tested at 50% RH and 23°C (73°F)ASTM C639Flow (sag or slump)inches (mm)0ASTM C603Extrusion Rateg/minute140Working Timeminutes20ASTM C679Tack-free Time, 77°F, 50% RHminutes40Curing Time at 77°F (25°C) and 50% RHdays7-14VOC Content2g/L31As Cured – After 21 days at 50% RH and 77°F (25°C)ASTM D2240Durometer Hardness, Shore Apoints34ASTM C794Peel Strengthlb/in (kg/cm)30 (5.4)ASTM C719Joint Movement Capabilitypercent±50ASTM C1135Tensile Adhesion StrengthAt 25% extensionAt 50% extensionPsi (MPa)Psi (MPa)40 (0.276)60 (0.414)

Additional Information:

• Delivery Time: 1 MONTH

PRODUCT DESCRIPTION   Technology Silicone Chemical type Oxime silicone Appearance  Thixotropic Paste  Colour White/Black/Grey Components One component – requires no mixing Cure Room temperature vulcanizing (RTV) Application Weatherproofing sealant Anabond 987 is a single component, self priming, nonslumping, non-corrosive, low odour, low volatile silicone weatherproofing sealant designed for general glazing and weather sealing in curtain wall and building facades. The product provides elastomeric seal from -50??? to 160??? without hardening, cracking or becoming brittle under normal weather conditions. It is unaffected by sunlight, rain, ozone and snow and exhibits excellent unprimed adhesion to most common building components with excellent weatherability. It extrudes easily in any weather condition and cures at room temperature by reaction with atmospheric moisture in the air to form a durable, flexible silicone rubber seal. Typical Properties of uncured material   Specific gravity at 30 ± 20C ATM*-R004 (JIS K6820)  1.45 -1.55 Extrusion rate for 20g at 30 ± 20C, orifice 2.6, pressure 3.0 kg/cm2, ATM-R047 (BS 5889) seconds 20 - 60 Flash Point Refer MSDS Curing performance  The product cures on exposure to moisture in the air, typically developing a skin within minutes, becoming tack free within minutes to hours. After skin formation, cure continues inward from the surface.  Optimum physical properties are reached after curing for 7 to 14 days at 30±20C, 55±5% RH.   The rate of surface/depth cure depends on the relative humidity and temperature of the environment, thickness of the adhesive and the area under the joint. Curing time is extended at lower humidity levels.   Skin forming time –  Surface cure, ATM-R017 minutes ≤ 30 Tack-free time ATM-R017 minutes ≤ 80 Depth cure, ATM-R015. mm/day ≥ 1.5  Operating parameters  Application temperature ???C 10 to 40 In service temperature ???C -50 to +160 Short exposure  ???C 180    Typical properties of cured material  Cured for 7 days at 30 ± 20C, 55±5% RH  Physical Properties Tensile Strength,  ATM-R020  (ASTM D412) kg/cm² ≥ 08 Elongation,  ATM-R020  (ASTM D412) % ≥ 500 Durometer Hardness,  ATM-R019 (ASTM D2240) Shore A 20 - 30  Adhesive properties  Adhesion is good on ceramic, wood, glass, Aluminum, PVC, Brick and other building materials.  General Information  This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials.  Handling  Before handling, read product safety data sheets (MSDS) and container labels for safe use.   Directions for use  Substrate preparation  Surfaces to be adhered or sealed should be free of dirt, oil and other contaminants. For best performance clean the surface with a solvent such as isopropyl alcohol, acetone or methyl ethyl ketone or with coarse lint free cloth

Additional Information:

• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 25*4 NO 100 NO

GST 18 % INCLUDING,FREIGHT EXTRA

•Silirub Color is a neutral cure silicone sealant particularly suitable for interior & exterior sealingapplications such as joints, weather sealing, connection JointsApplications:
•Telecom Shelters, uPVC Profiles, aluminium fenestration, door & window frames, ACP glass, brick,concrete, wood
•Building and construction joints
•Topsealing between treated wood and glass and between PVC and glass or aluminium and glass
•Sealing between PVC and glass.
PropertiesBasePolysiloxaneConsistencyPasteCuring SystemMoisture CureSkin formation (20°C/65% R.H.)Transp. + bril.white: 10 min.Other colours: 9 min.Curing Rate (20°C/65% R.H.)Ca. 1 to 2 mm/24hHardness (DIN 53505)Transp. + bril.white : 25 ± 5 Shore AOther colours:.35 ± 5 Shore ATooling timeTransp. + bril.white: 15 min.Other colours: 10 min.Specific Gravity (DIN 53479)Transp. + bril.white : 1,004 g/mlOther colours:.1,26 g/mlTemperature Resistance-60°C to +140°CMaximum allowed Distortion25 %Elastical Recovery (DIN 7389)> 80 %Maximum Tension (DIN 53504)Transp. + bril. White: 1,36 N/mm²Other colours: 1,20 N/mm²Elasticity Modulus 100 % (DIN 53504)Transp. + bril. White: 0,39 N/mm²Other colours: 0,50 N/mm²Elongation at Break (DIN 53504)Transp. + bril. White: 600%Other colours: 550%Characteristics:
•Panel / Perimeter / Project Sealant
•Stays elastic after curing
•Good resistance to UV / ozone / vibration / moisture / airborne pollutants
•Excellent weatherproofing properties
•Easy tooling and soft extrude able properties
•Neutral cure - RTV
•Non slumping, can be used in overhead/vertical joints
•Excellent adhesion to most of the substrates including metals, aluminium, concrete, steel, glass,wood, stone and masonriesColor: Packaging: Product Shade Card:RAL 8017, 8007, 9001, 9010, Ivory & Cartridge 280ml & on requestLight grey sausage of 600ml
Product Features:
•Silirub Color Silicone Sealant is a neutral cure silicone sealant particularly suitable for interior andexterior sealing applications such as joints, weather sealing, connection joints.
•Silirub Color Silicone Sealant has good resistance to UV / ozone / vibration / moisture / airbornepollutants/cleaningdetergents and many solvents.
•Silirub Color Silicone Sealant has excellent weatherproofing properties.
•Silirub Color Silicone Sealant has easy tooling and soft extrudable properties.
•Silirub Color Silicone Sealant is Neutral cure - RTV
•Silirub Color Silicone Sealant is Non slumping, can be used in overhead/vertical joints.
•Silirub Color Silicone Sealant has Excellent adhesion to most of the substrates including metals,aluminium,concrete,steel,glass,wood, stone and masonries.
•Silirub Color Silicone Sealant is available in RAL 8017, 8007, 9001, 9010, Ivory, Light grey colors.

Additional Information:

• Production Capacity: WITHIN 10 DAYS
• Delivery Time: WITHIN 10 DAYS
• Packaging Details: 280 ML

COLOR ( WHITE / BLACK / CLEAR )
GST 18% INCLUDING,FREIGHT EXTRA
Technical Data:Base PolysiloxaneConsistency PasteCuring System Moisture CureSkin formation (20°C/65% R.H.) Transp. + bril.white: 10 min.Other colours: 9 min.Tooling time Transp. + bril.white: 15 min.Other colours: 10 min.Curing Rate (20°C/65% R.H.) Ca. 1 to 2 mm/24hHardness (DIN 53505) Transp. + bril.white : 25 ± 5 Shore AOther colours:.35 ± 5 Shore ASpecific Gravity (DIN 53479) Transp. + bril.white : 1,004 g/mlOther colours:.1,26 g/mlTemperature Resistance -60°C to +140°CElastical Recovery (DIN 7389) > 80 %Maximum allowed Distortion 25 %Elasticity Modulus 100 % (DIN 53504) Transp. + bril. White: 0,39 N/mm²Other colours: 0,50 N/mm²Maximum Tension (DIN 53504) Transp. + bril. White: 1,36 N/mm²Other colours: 1,20 N/mm²Elongation at Break (DIN 53504) Transp. + bril. White: 600%Other colours: 550%Product:Silirub PS is a neutral cure silicone sealantparticularly suitable for interior & exterior sealingapplications such as joints, weather sealing,connection Joints.Characteristics:- Panel/Perimeter/Project Sealant.- Stays elastic after curing- Good resistance to UV / ozone / vibration /moisture / airborne pollutants.- Excellent weatherproofing properties.- Easy tooling and soft extrude able properties.- Neutral cure - RTV- Non Slumping, can be used inoverhead/vertical joints- Excellent adhesion to most of the substratesincluding metals, aluminium, concrete, steel,glass, wood, stone and masonries.Applications:- Telecom Shelters, uPVC Profiles, aluminiumfenestration, door & window frames, ACPglass, brick, concrete, wood.- Building- and construction joints- Topsealing between treated wood and glassand between PVC and glass or aluminium andglass.- Sealing between PVC and glassPackaging:Colour: transparent, brilliant white, black, grey,ivoryPackaging: cartridge 280ml, on request sausagesof 600ml

Additional Information:

• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 280 ML & 600 ML COLOR ( W,B,C)

COLOR :BLACK / WHITE/GREY/CLEAR
GST 18% INCLUDING,FRIEGHT EXTRA

•SILIRUB WSL+Revision: 01/0/201 Page 1 of 2Remark: The directives contained in this documentation are the result of our experiments and of our experience and have been submittedin good faith. Because of the diversity of the materials and substrates and the great number of possible applications which are out of ourcontrol, we cannot accept any responsibility for the results obtained. In every case it is recommended to carry out preliminaryexperiments.Technical Data:Base PolysiloxaneConsistency Thixotropic pasteCuring System Moisture CureSkin formation 10-15 min (20°C/65% R.H.)Tooling time Ca. 30 min.Curing Rate 2 mm/24h (20°C/65% R.H.)Hardness 25 ± 5 Shore ASpecific Gravity 1,30 g/mlTemperature Resistance -60°C to +180°CElastic Recovery > 80%Maximum allowed Distortion 30%Elasticity Modulus 100% 0,50 N/mm² (DIN 53504)Maximum Tension 1,27 N/mm² (DIN 53504)Elongation at Break > 700 % (DIN 53504)Product:Silirub WSL+ is a high-quality neutral cure, highlyelastic one-component joint sealant based onsilicones. It has been developed for weathersealing of expansion joints in the façade industry.Characteristics:- Compatible with laminated glass- Compatible with secondary sealants based onpolysulfide and silicone in dual-sealedinsulating glass units- Very easy application- Permanent colors, UV-resistant- Stays elastic after curing- Very good adhesion on many materials- Low modulus according to ISO standards- Resistant against UV-radiation, rain, frost, wind,ozone and extreme temperatures- Excellent adhesion properties on glass,laminated glass, coated aluminium, galvanisedsteel, aluminium composite panels (ACP),stones, concrete and masonryApplications:
•Weatherseal in curtain wall applications
•Ideal for expansion, perimeter, connection andother movement joints between various buildingmaterials
•Compatible with double glazed window unitsPackaging:Colour: grey, blackPackaging: cartridge 300ml, foil bag 600mlShelf life and storage:12 months from date of manufacturing in unopenedpackaging stored in a cool and dry place attemperatures between +5°C and +25°.
Surfaces:Type: All usual porous and non-porous buildingsurfacesState of Surface: clean, dry, free of dust and greasePreparation: porous surfaces in water loadedapplications should be primed with Primer 150 – noprimer required for non-porous surfaces. SurfaceActivator should be used to enhance adhesion tonon-porous surfaces.Joint dimensionsJoints in window glass and in window connectionsTop sealing = minimal width 4 mm, depth at least 6mm.Minimal width window connection joints: 10 mm.Weatherseal and other application Joint recommandation Joint width Joint depth5-10mm 5mm10-30mm depth=1/2 * width Application:Method: caulking gunApplication temperature: +1°C to +35°CClean: with white spirit immediately after useFinish: with soapy water before skinningRepair: with Silirub WSL+Health- and Safety Recommendation:Apply the usual industrial hygiene. Consult the labelfor more information.
Remarks:Chemically completely neutralDue to the wide variety materials used in façadetechnology a preliminary compatibility test isnecessary.Comments:
•Not suitable for use as structural glazingadhesive
•Do not use this sealant on natural stones likemarble, etc. For this application we recommendSilirub NS-W
•When applied as “weather seal” in curtain wallapplications, compatibility with powder-coatedaluminum needs to be established. SoudalSurface Activator will improve adhesion onpowder-coated aluminum.Technical Norms/Conforms with:- Meets ISO 11600 G 25 LM- Meets ASTM C-920 Type S, Grade NSClass 25, Use T,NT, A, and G

Additional Information:

• Delivery Time: within 2 days
• Packaging Details: 300 ML & 600 ML

ABOVE PRICE IS INCLUDING GST 18 %.
Technical Data: Base Siliconized Acrylic Dispersion Consistency Paste Curing System Moisture Cure Skin formation (20°C/65% R.H.) Ca 20 - 30 min. Shrinkage (DIN 52451) ≤15% Temperature Resistance -20°C to +80°C Maximum allowed Distortion 15% - 20% * This varies according to ambient conditions such as temperature, humidity, substrate etc. Product: Acryrub Exterior is a high-quality, plasto-elastic, one-component joint sealant based on siliconized acrylic dispersions. Developed for both interior Characteristics: - Interior & exterior purpose - Excellent crack bridging properties - - Perimeter sealing - Excellent movement capability Applications: - Joints with movements up to 15% - 20%. - Sealing compound for cracks in concrete and plaster - Connection joints in the building industry - Joints between windowsills (uPVC, aluminium & Packaging: Colour: white Packaging: cartridge 425g, sausage 425g & 850g Not suitable for: Joint Size: Minimum Width: 5mm Maximum Width: 20mm Minimum Depth: 5mm Recommandation: jointh depth = joint width Use PE backer rods in case of large joint dimensions to avoid three-sided adhesion Applying the sealant: Method: Apply the sealant by means of a handheld or pneumatic caulking gun. Smoothen the sealant with a filling-knife. Application temperature: +5°C to +35°C, do not apply when rain or frost are imminent Clean: Uncured Acryrub Exterior may be removed from tools with water. Cured sealant must be removed mechanically. Finishing: with water Repair: with Acryrub Exterior.

Additional Information:

• Delivery Time: STOCK AVAILABLE
• Packaging Details: WHITE/CLEAR/BLACK

GST 18% INCLUDING IN ABOVE PRICE.

 PolyurethaneColour White, BlackConsistency Paste, easy to extrudeSkin formation (20°C/65% R.H.)* 20 - 30 min.Curing System Moisture CureCuring Rate (20°C/65% R.H.)* 4 mm/24hHardness (DIN 53505) 40 ± 5 Shore ASpecific Gravity (DIN 53479) 1,20 g/mlTemperature Resistance -40°C to +90°CElastical Recovery (ISO 7389) > 70%Maximum allowed Distortion 15%Elasticity Modulus 100% (DIN 53504) 0,55 N/mm2Tensile strength (DIN 53504) 1,75 N/mm2Elongation at Break (DIN 53504) < 560%Solids Content > 90%(*) these values may vary depending on environmental factors such as temperature, moisture, type and size of substratesProduct:Soudaflex 611 has been specially developed for Indiansubtropical conditions after a decade of research,practical application understanding of Indian climateconditions, it is most suitable in high temperature &extreme humid conditions.Soudaflex 611 is specifically designed for sealingapplication in the Bus & Coach, Truck, Earth MovingEquipments, Tractor, Forklift, OEM, Repair Auto AfterMarkets & various other commercial and industrialvehicles.It bonds a variety of material like are FRP, GRP, timber,plywood, metals, particularly aluminium (includinganodized components), sheet steel (includingphosphated, chromated and zinc-plated components),coated metals and paint coatings (two-part systems),ceramic materials & plastics.??????????????????????????????????????????????????? Bonds well to a wide variety of substrates.??? Excellent resistance to many chemicals.??? Can be over-painted & non-sag consistency.??? Especially developed for automotive and busindustry, bodywork, container applications.??? Suitable for making permanent elastic seals ofhigh adhesive strength.??? Good resistance to aging, weathering – suitablefor indoor and outdoor.??? Vibration and sound damping properties.??? Sandable & over-paintable with many water,solvent based paints (preliminary testsrecommended).
Application  General coach-building, caravans & motorhomesassembly and repairing.??? Bus & truck industries.??? Thermal & acoustic insulation technology inrefrigeration, air-conditioning.??? Suitable substrate materials are timber, metals,particularly aluminium (including anodisedcomponents), sheet steel (including phosphated,chromated and zinc-plated components), metalprimers and paint coatings (two-part systems),ceramic materials and plastics.??? For elastic bonding to untreated metals & plasticsthe use of Primers is recommended.
Surface Preparation:The surfaces to be treated should be perfectly clean,dry and free from dust, oil and grease. It is necessary toapply Soudal Universal Cleaner 165 on glass.The adhesion on normal vehicle varnishes generallydoes not require the use of Soudal Universal Primer175. It is advisable to carry out preliminary adhesiontests on the support. Specific guidance regarding theuse of Primers may be obtained by submittingsubstrate samples to our laboratory.
Packaging & Colour:Colour: Black, WhitePackaging: 600ml sausageStorage/Shelf Life:The storage and application of PU sealant affect theshelf life and usage. The shelf life of all given isunderstood to be 12 months from the date ofmanufacturing if kept in the temperature from 5°C to35°C.In the specific case of India, since practically thetemperature rises up to 45°C to 50°C, the sealant canstill be used, due to extreme heat or humidity, the skinformation time of the same may be little faster in thosespecific conditions, yet the sealant can still be usedwith effectiveness.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 600 ML

GST INCLUDING 18%

seal anything from the smallest silicon chip to the world's tallest skyscrapers. Sealants are used a wide range of industries including construction, electronics, automotive, aerospace. Our Industrial Silicone Sealant are provided as per our client's specification & requirement.
Main Applications:
Standard glazing and window sealing
Any non porous substrate like glass or aluminum
General sealing and assembly
Automotive glazing and sealing
General bonding and insulation
Sign manufacturing/assembly
Clean rooms, shelters and pre fabricated structures

Additional Information:

• Delivery Time: within week
• Packaging Details: All pack in Available.

GST 18% INCLUDING.FREIGHT EXTRA

Fix ALL High Tack Revision: 21/10/2013 Page 1 from 2 Remark: This technical data sheet replaces al previous versions. The directives contained in this documentation are the result of our experiments and of our experience and have been submitted in good faith. Because of the diversity of the materials and substrates and the great number of possible applications which are out of our control, we cannot accept any responsibility for the results obtained. Since the design, the quality of the substrate and processing conditions beyond our control, no liability under this publication are accepted. In every case it is recommended to carry out preliminary experiments. Soudal reserves the right to modify products without prior notice.  Technical data Basis MS Polymer Consistancy Stable paste Curing system Moisture curing Skin formation* (20°C / 65% R.H.) Ca. 5 min Curing speed * (20°C / 65% R.H.) 3 mm/24h Hardness 65 ± 5 Shore A Density 1,47 g/ml Elastic recovery (ISO 7389) > 75 % Maximum allowed distortion ± 20 % Temperature resistance -40 °C → 90 °C Max. tension (DIN 53504) 3,50 N/mm² Elasticity modulus 100% (DIN 53504) 2,30 N/mm² Elongation at break (DIN 53504) 400 % Application temperature 5 °C → 35 °C (*) these values may vary depending on environmental factors such as temperature, moisture, and type of substrates. Product description Fix ALL High Tack is a high quality, neutral, elastic, 1-component adhesive sealant based on MS-Polymer with a very high initial tack. Fix ALL High Tack is a KOMO-certified construction adhesive based on BRL3107. Properties  High initial tack reducing the need for initial support. Fast curing Good extrudability high shear strength after full cure (no primer)  Stays elastic after curing and very sustainable  No odour. Can be painted with water based systems  Good colour stability, weather and UV resistance  Does not contain isocyanates and no silicones Good adhesion on wet substrates Applications Sealing and bonding in the building and construction industry. Elastic bonding of panels, profiles and other pieces on the most common substrates (wood, MDF, chipboard, etc). Elastic structural bonding in car and container industry. Packaging Colour: white, black, grey, alu grey, brown, beige Packaging: 290 ml cartridge Shelf life 12 months in unopened packaging in a cool and dry storage place at temperatures between +5°C and +25°C. Chemical resistance Good resistance to water, aliphatic solvents, hydrocarbons, ketones, esters, alcohols, diluted mineral acids and alkalis and (salt) water. Poor resistance to aromatic solvents, concentrated acids and chlorinated hydrocarbons.Fix ALL High Tack Revision: 21/10/2013 Page 2 from 2 Remark: This technical data sheet replaces al previous versions. The directives contained in this documentation are the result of our experiments and of our experience and have been submitted in good faith. Because of the diversity of the materials and substrates and the great number of possible applications which are out of our control, we cannot accept any responsibility for the results obtained. Since the design, the quality of the substrate and processing conditions beyond our control, no liability under this publication are accepted. In every case it is recommended to carry out preliminary experiments. reserves the right to modify products without prior notice.  Substrates Substrates: all usual building substrates, treated wood, PVC, plastics Nature: clean, dry, free of dust and grease. Surface preparation: Porous surfaces in water loaded applications should be primed with Primer 150. All smooth surfaces can be treated with Surface

Additional Information:

• Delivery Time: within 2 days

ABOVE PRICE IS INCLUDING GST 18%
Product description WACKER® GN - GENERAL NEUTRAL transp. is a one-part, neutral silicone sealant with outstanding adhesion to most building substrates. It further exhibits good weather resistance and workability for glazing. Properties WACKER® GN - GENERAL NEUTRAL transp. cures at room temperature in the presence of atmospheric moisture to give a permanent flexible silicone rubber.
Application - Sealant for internal connection and expansion joints - Suitable for fenestration and glazing applications Adhesion WACKER® GN - GENERAL NEUTRAL transp. exhibits excellent primerless adhesion to most non-porous siliceous materials (e.g. glass, tiles, ceramics, enamel, glazed tiles); metals (e.g. aluminum, steel, zinc or copper); impregnated, varnished or painted wood; and some plastics. Users must carry out own tests due to the great variety of substrates. The adhesion can be improved in many cases by pretreatment of the substrate with a primer. Processing The substrate areas that will be in contact with the sealant must be clean, dry and free of all loose material such as dust, dirt, rust, oil and other contaminants. Non-porous substrates should be cleaned with a solvent and clean, lint-free, cotton cloth. Remove residual solvent before it evaporates with a fresh clean, dry cloth. For application from cartridges cut thread open, fix nozzle on top and cut to required bead size. The sealant can be applied in beads or layers. It requires moisture in order to cure. The curing time can take longer at lower temperatures, lower humidity or by low volume of air exchange
Special features - long shelf life - non-sag - readily gunnable both at low (+5 °C) and high (+40 °C) temperatures - good tooling properties - excellent weatherability - excellent adhesion - excellent durability - non-corrosive to metals - suitable for alkaline substrates such as concrete, mortar, fibrous cement.
Restrictions on use WACKER® GN - GENERAL NEUTRAL transp. is not recommended for sealing of aquarium or for long term use under water. WACKER® 121 - AQUARIUM has been specifically developed for aquarium applications. WACKER® GN - GENERAL NEUTRAL transp. is not suitable for food grade applications where the joints are likely to come in contact with food. For this application please use WACKER® 120 – FOOD
WACKER® GN - GENERAL NEUTRAL transp. is usually supplied in standard size cartridges that fit all standard caulking guns. Safety notes Comprehensive instructions are given in the corresponding Material Safety Data Sheets. They are available on request from WACKER subsidiaries or may be printed via WACKER web site http://www.wacker.com. During vulcanization methylethylketoxime is released. These vapors should not be inhaled for long periods or in high concentration. Hence, good ventilation of the work place is necessary. Should uncured silicone rubber come into contact with eyes or mucous membranes, the affected area must be rinsed thoroughly with water as irritation will otherwise be caused. Avoid prolonged contact of uncured sealant with the skin - use a dry cloth or paper to remove it. Keep out of reach of children. Cured silicone rubber, however, can be handled without any risk to health. Product data Typical general characteristics Inspection Method Value Cure type Oxime, unfilled Uncured / unvulcanized paste Density at 23 °C ISO 1183-1 A 0,98 g/cm³ Consistency ISO 7390 non-sag Extrusion rate at 6 bar internal method 504 g/min Skin forming time at 23 °C / 50 % r.h. internal method approx. 10 - 30 min Cured / vulcanized rubber Hardness Shore A ISO 868 24 Modulus at 100 % (joint) ISO 8339-A 0,6 N/mm² Tensile strength (joint) ISO 8339-A 0,43 N/mm2 Ultimate elongation (joint) ISO 8339-A 217 % Modulus at 100 % (S2-

Additional Information:

• Delivery Time: WITHIN WEEK
• Packaging Details: 270 ML

GST EXTRA :18% 
Dow Corning  995 SiliconeStructural Glazing SealantFEATURES Odorless, non-corrosive curesystemCures to form an extremely toughelastomeric rubber ensuring adurable, flexible, watertight bondBENEFITS Excellent weatherability and highresistance to ultraviolet radiation,heat and humidity, ozone andtemperature extremes Excellent mechanical properties Successfully tested for use inprotective glazing applications Excellent unprimed adhesion towide range of substrates includingcoated, enameled, and reflectiveglasses; anodized and polyestercoated or painted aluminum profilesincluding mostfluoropolymerbased paints such asKynar  Meets global standards for structuralglazing (American, China,Europe)COMPOSITION One-part, neutral-cure elastomericsealantHigh ultimate tensile strength sealant ideally suited for structuralbonding and protective glazing applicationsAPPLICATIONS Silicone structural glazing and protective glazing applicationsTYPICAL PROPERTIESSpecification Writers: These values are not intended for use in preparingspecifications. Please contact your local Dow Corning sales office or your GlobalDow Corning Connection before writing specifications on this product.Method Test Unit ResultAs SuppliedColor Black, gray,whiteMIL-S-8802 Tack-Free Time, 50% RH minutes 65Curing Time 25C (77F) at 50% RH days 7-14Full Adhesion days 14-21Flow, Sag, or Slump inches 0.1Working Time minutes 10-20Specific Gravity 1.339VOC Content1 g/L 30As Cured After 7 days at 25C (77F), 50% RHASTM2 D2240 Durometer Hardness, Shore A points 40ASTM D0412 Ultimate Tensile Strength Psi (MPa) 350 (2.41)Ultimate Elongation % 525ASTM D0624 Tear Strength, die B ppi 49ASTM C0794 Peel Strength ppi 40As Cured After 21 days at 25C (77F), 50% RHASTMC1135 Tensile at 25% Elongation psi (MPa) 43 (0.30)ASTMC1135 Tensile at 50% Elongation psi (MPa) 65 (0.43)Ultimate Tensile Strength psi (MPa) 170 (1.17)ASTM C719 Joint Movement Capability % 501Based on South Coast Air Quality Management District of California. Maximum VOC is listed bothinclusive and exclusive of water and exempt compounds. For a VOC datasheet for a specific sealantcolor, please send your request to product.inquiry@dowcorning.com.2 ASTM: American Society for Testing and Materials.DESCRIPTIONDow Corning995 Silicone StructuralGlazing Sealant is a one-componentneutral-curing silicone sealantdesigned specifically for structuralbonding applications of glass andmetal in factory or field situations.The rate of surface cure and cure-indepthof most one-component RTVsilicone sealants is affected by thetemperature and humidity of theenvironment. However, anenvironment of high temperatures incombination with high humidity mayslow the surface cure rate ofDow Corning 995 Silicone StructuralGlazing Sealant.Dow Corning is a registered trademark of Dow Corning Corporation.We help you invent the future is a trademark of Dow Corning Corporation.2009, November 12 XIAMETER is a registered trademark of Dow Corning Corporation.Ref. No. 62-1260F-01  2009 Dow Corning Corporation. All rights reserved.ColorsThis product is available in black,gray, and white. Please contact yourlocal Dow Corning Sales ApplicationEngineer for availability.APPROVALS/SPECIFICATIONSDow Corning 995 Silicone StructuralGlazing Sealant has been internallytested and is designed to meet orexceed the test requirements of: Federal Specification TT-S-001543A (COM-NBS) Class Afor silicone building sealant Federal Specification TT-S-00230C (COM-NBS) Class A forone-component building sealant ASTM Specification C-920 TypeS, Grade NS, Class50, Use NT, Gand A ASTM C1184 StandardSpecification for StructuralSilicone Sealant Chinese specification GB 16776for structural glazing SNJF VEC

Additional Information:

• Production Capacity: AVAILABLE
• Delivery Time: within 2 days
• Packaging Details: 305 ML PACKING

PRODUCT DESCRIPTIONAlstone SS-900 Structural Sealant / Adhesive is a highmodulus one-component, self priming, shelf-stable,neutral-cure, elastomeric adhesive specificallyformulated for silicone structural glazing, exhibiting thefollowing unique features:• Excellent UV resistance.• Excellent unprimed adhesion to most common buildingsubstrates, including glass, reflective glass, anodizedaluminum, granite and paints, including most fluoropolymer based paints.• Excellent shelf life and “Use By” dating.• Noncorrosive by-products.• 15-year performance warranty available.• Cures to extremely tough elastomeric rubber Structuralapplications require prior testing and written Test reviewby Alstone.Basic UsesAlstone SS-900 Structural Sealant is designed for use instructural applications such as factory or field glazing ofglass and metal. Once cured, this adhesive forms adurable, flexible, watertight bond that can be warrantedfor 15 years.LimitationsAlstone SS-900 Structural Sealant should not be applied:• To building materials that bleed oils, plasticizers orsolvents – materials such as impregnated wood,oil-based caulks, green or partially vulcanized rubbergaskets or tapes.• In totally confined spaces (the sealant requiresatmospheric moisture for cure).• When surface temperatures exceed 55°C (131°F).• Where painting of the sealant is required, as the paintfilm may crack and peel.• In below-grade applications.• For use as an interior penetration firestop sealingsystem.• In horizontal floor joints where abrasion and physicalabuse are likely to be encountered.
To frost-laden or damp surfaces.• For continuous immersion in water.This product is neither tested nor represented assuitable for medical or pharmaceutical uses.COMPOSITION AND MATERIALSAlstone SS-900 Structural Sealant is a one-part,ready-to-use material that has the consistency oftoothpaste. This consistency remains uniform overa wide temperature range from -15 to 55°C (5to 131°F), allowing the sealant to be applied easilyat most temperatures.TYPICAL PROPERTIESThese values are not intended for use in preparing specifications  As SuppliedAs Cured - After 7 days at 25°C (77°C), 50% RHAs Cured - After 21 days at 25°C (77°C), 50% RHAs Cured - After 21 days at 25Subjected to 4,500 hours QUV ASTM G-53°C (77°C), 50% RH andSpecific Gravity.............................................................Color..............................................................................Tack-Free Time, 50% RH, hours...................................Curing Time, 50% RH, at 25°C (77 C), days................Full Adhesion, days........................................................Flow, Sag or Slump, inches............................................Working Time, minutes..................................................°1.36Black1.57-1414-21<0.115-25Durometer Hardness, Shore A, points............................Ultimate Tensile, psi.......................................................Ultimate Elongation, %..................................................Tear Strength, die B, ppi.................................................Peel Strength, ppi............................................................403505254940Tensile at 25%, psi...........................................................Tensile at 50%, psi...........................................................Joint Movement Capability, %.........................................4875±50Tensile at 25%, psi............................................................Tensile at 50%, psi............................................................5078
COMPOSITION AND MATERIALSAlstone SS-900 Structural Sealant is a one-part,ready-to-use material that has the consistency oftoothpaste.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 300ML & 600 ML

ABOVE PRICE IS INCLUDING OF GST 18%.
Projectseal High Performance Silicone SealantDescription:Silirub Color is a neutral cure silicone sealant particularly suitable for interior & exterior sealingapplications such as joints, weather sealing, connection JointsApplications:• Telecom Shelters, uPVC Profiles, aluminium fenestration, door & window frames, ACP glass, brick,concrete, wood• Building and construction joints• Topsealing between treated wood and glass and between PVC and glass or aluminium and glass• Sealing between PVC and glassPropertiesBasePolysiloxaneConsistencyPasteCuring SystemMoisture CureSkin formation (20°C/65% R.H.)Transp. + bril.white: 10 min.Other colours: 9 min.Curing Rate (20°C/65% R.H.)Ca. 1 to 2 mm/24hHardness (DIN 53505)Transp. + bril.white : 25 ± 5 Shore AOther colours:.35 ± 5 Shore ATooling timeTransp. + bril.white: 15 min.Other colours: 10 min.Specific Gravity (DIN 53479)Transp. + bril.white : 1,004 g/mlOther colours:.1,26 g/mlTemperature Resistance-60°C to +140°CMaximum allowed Distortion25 %Elastical Recovery (DIN 7389)> 80 %Maximum Tension (DIN 53504)Transp. + bril. White: 1,36 N/mm²Other colours: 1,20 N/mm²Elasticity Modulus 100 % (DIN 53504)Transp. + bril. White: 0,39 N/mm²Other colours: 0,50 N/mm²Elongation at Break (DIN 53504)Transp. + bril. White: 600%Other colours: 550%Characteristics:• Panel / Perimeter / Project Sealant• Stays elastic after curing• Good resistance to UV / ozone / vibration / moisture / airborne pollutants• Excellent weatherproofing properties

Additional Information:

• Production Capacity: AVILABLE
• Delivery Time: WITHIN WEEK
• Packaging Details: 280 ML PACK

GST 18% INCLUSIVE OF GST.
PACKING  300 ML.
One-part neutral cure silicone sealantFeatures & Benefits• Adheres to a wide range of building materials and finishes• Neutral cure; will not corrode galvanized/zinc-coated steel or attack concrete• Excellent resistance to weathering, ultra-violet radiation, vibration, moisture, ozone, temperature extremes, airborne pollutants, cleaning detergents and many solvents• Long life reliability• Meets International Standards such as CNS 8903, BS 5889, BS EN ISO11600 20LM• Strong elastic seal capable of withstanding movements up to ± 25% of original joint width• Non-slumping; can be used in vertical and overhead joints• Easy to use – one part, no mixing required• Can be applied in any season• Good weatherability – it is virtually unaffected by sunlight, rain, snow, ozone or temperature extremes• Easy to use• Bonds to most common construction materials without use of primer• Excellent recovery from extension and compression• Ease of application – ready to use as suppliedApplicationsDOWSIL™ 688 Glazing and Cladding Sealant is a one-part neutral cure silicone sealant designed for a wide range of glazing, weather sealing and professional caulking applications. It will bond to form a strong weatherproof seal on most common building materials.Typical PropertiesSpecification Writers: These values are not intended for use in preparing specifications.Test1PropertyUnitResultAs Supplied – tested at 25°C, 50% relative humidityFlow, Sag or SlumpNilApproximate Working Time2Minutes101. ASTM: American Society for Testing and Materials2. Sealant cure rate and working time may vary with temperature and humidity.
Typical Properties (Cont.)TestPropertyUnitResultTack Free Time:TranslucentMinutes30ColorsMinutes30Specific Gravity:Translucent1.03Colors1.40As Cured – After 7 days at 25°C, 50% relative humidityDurometer Hardness, Shore A:TranslucentPoints27ColorsPoints32ASTM D412Ultimate Tensile StrengthMPa1.10ASTM D412Ultimate Elongation at Break@0Temperature Stability°C-20 to 120Movement Capability± 25DescriptionDOWSIL™ 688 Glazing and Cladding Sealant is one-part neutral cure, construction grade sealant that easily extrudes in any weather. It quickly cures at room temperature by reaction with moisture in the air to form a durable, flexible silicone rubber seal.It has excellent unprimed-adhesion to most construction materials.SpecificationsMeets the requirements of: CNS 8903 A 2136 SR-1-9030-A-N, BS 5889 Type B, BS EN ISO11600 20LM.
How to UsePlease consult the application manual for detailed information on state-of-art application methods and joint design. Please contact your local sales office for specific advice.PreparationClean all joints and glazing pockets, removing all foreign matter and contaminants such as grease, oil, dust, water, frost, surface dirt, old sealants, or glazing compounds and protective coatings.
How to Use(Cont.)Application MethodInstall backing material or joint filler, setting blocks, spacer shims, and tapes. Areas adjacent to joints may be masked to ensure neat sealant lines. Primer is generally not required on non-porous surfaces. It is recommended that a field test be carried out prior to application. To confirm optimum adhesion on either a porous or non-porous surface, adhesion testing should always be carried out prior to the commencement of any project. Please contact your local sales office for specific advice.Apply DOWSIL™ 688 Glazing and Cladding Sealant in a continuous operation using a positive pressure. Tool the sealant with light pressure to spread the sealant against the backing material and joint surfaces before a skin forms. The applied sealant should be tooled and masking tape removed before the sealant has formed a cured skin.
Handling Precautions

Additional Information:

• Delivery Time: WITHIN WEEK
• Packaging Details: 300 ML & 600 ML

33 GM PACK : INCLUDING GST 18%. 
Technology Silicone Chemical type Oxime silicone Appearance Thixotropic paste ColourClear Components One component – requires no mixingCureRoom temperature vulcanizing (RTV) Application Bonding /SealingAnabond 666T Max gasket sealant is a single component, non-slumping, low odour, low volatile silicone adhesive/sealant. It is designed to provide reliable “formed-in-place” gaskets for mechanical assemblies where high temperatures are experienced. The material cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. The product resists aging, weathering and thermal cycling without hardening, shrinking or cracking. It has good adhesion to substrates like aluminium, mild steel, glass, ceramics, corks and many plastics.This is a universal gasket maker and it meets every sealing need in automobile engine, timing covers, oil sump applications, valve covers, rocker covers, water pumps, end seals, intake manifolds and rear axle housings. Also used as a sealant and adhesive for assembly and repair of industrial furnaces, ovens, boilers, exhaust stacks, high temperature ducting, bonding of sensitive electronic components and sub assemblies.Typical Properties of uncured materialSpecific gravity at 30 ± 2°C ATM*-R004 (JIS* K6820) 1.02 -1.06Flow, sag or slump at 30 ± 2°CATM-R016 (ASTM* C639)Non sag Extrusion rate for 20g at 30 ± 2°C, orifice 2.6, pressure 3.0 kg/cm2, ATM-R047 (BS* 5889) seconds 10 - 20Pressure resistance at 30±2°C, ATM-R034 (JIS K6820)kg/cm2≥ 100 Flash Point Refer MSDS
Curing performanceThe product cures on exposure to moisture in the air, typically developing a skin within minutes, becoming tack free within minutes to hours. After skin formation, cure continues inward from the surface. Optimum physical properties are reached after curing for 7 days at 30±2°C, 55±5% RH.The rate of surface/depth cure depends on the relative humidity and temperature of the environment, thickness of the adhesive and the area under the joint. Curing time is extended at lower humidity levels.Curing tested at 30 ± 20C, 55 ± 5% RHSkin forming time – Surface cure, ATM-R017 minutes 3 - 8Depth cure, ATM-R015.mm/day≥ 3.0 Operating parametersApplication temperature  C 10 to 40In service temperature C-50 to +230 Short exposure  C 250Typical properties of cured materialCured for 7 days at 30 ± 20C, 55±5% RHPhysical PropertiesTensile Strength, ATM-R020 (ASTM D412) kg/cm² 10 - 20Elongation,ATM-R020 (ASTM D412)%≥ 300 Durometer Hardness, ATM-R019 (ASTM D2240) Shore A 25 - 35 Electrical PropertiesDielectric strength, ATM R119 (ASTM D149) kV/mm ≥ 18General InformationThis product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials.HandlingBefore handling, read product safety data sheets (MSDS) and container labels for safe use.

Additional Information:

• Production Capacity: AVAILABLE
• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 33 GM

ABOVE PRICE IS INLUDING GST 18%.
PRODUCT DESCRIPTION Technology MS Sealant / Adhesive Chemical type Silane modified polymer Appearance Smooth Paste Colour Off-White Components One component Cure mechanism Moisture curing Application Sealing/ Bonding
Anabond MS 9933 is a single component, non odourless, medium viscous and low modulus adhesive based on silane modified polymer free of solvents, isocyanates, silicones and PVC. The product cures on exposure to atmospheric humidity to form a durable elastomer and resists aging, weathering and thermal cycling without hardening, shrinking or cracking It has good adhesion to a wide variety of substrates without primer and compatible with suitable paint systems. Typically designed for interior and exterior applications and demonstrates good UV resistance. primary use is sealing seams, overlaps and secondary use is bonding. Typical field of application includes industrial and hand made vehicle and coach construction, railway carriage and container manufacture, ship and boat building, air conditioning and ventilation industries, civil and environmental engineering, building and construction, vehicle window glass glazing between rubber profile and glass
Typical Properties of uncured material Specific gravity at 30 ± 2°C ATM*-R004 (JIS* K6820) Flow, sag or slump at 30 ± 2°C ATM-R016 (ASTM* C639) Extrusion rate for 20g at 30 ± 2°C, orifice 2.6, pressure 3.0 kg/cm2 , ATM-R047 (BS* 5889) seconds Paint compatibility, ATM-R370 Flash Point Curing performance The product cures on exposure to moisture in the air, typically developing a skin within minutes, becoming tack Anabond® MS 9933 Japanese Industrial standard, ASTM – American Society for testing and materials, BS / Adhesive Silane modified polymer , non-corrosive, modulus sealant / based on silane modified polymer free of solvents, isocyanates, silicones and PVC. The product cures on exposure to atmospheric humidity to form a durable elastomer and resists aging, weathering and thermal cycling without hardening, shrinking or cracking. It has good adhesion to a wide variety of substrates without primer and compatible with suitable paint systems. Typically designed for interior and exterior applications and demonstrates good UV resistance. Its sealing seams, overlaps and joints and Typical field of application includes industrial and handmade vehicle and coach construction, railway carriage and container manufacture, ship and boat building, air conditioning and ventilation industries, civil and environmental engineering, building and construction, vehicle window glass glazing between rubber profile and 1.58 -1.62 Non sag econds 20 – 60 In principle compatible Refer MSDS free within minutes to hours. After skin formation, cure continues inward from the surface. develops functional cure in 24 hours days at 30±2°C, 55±5% RH. The rate of surface/depth cure depends on the relative humidity and temperature of the environment of the adhesive and depth of the extended at lower humidity levels. unexposed area, the longer the curing time. Curing tested at 30 ± 20C, 55 ± 5% RH Skin forming time – Surface cure, ATM-R017 Depth cure, ATM-R015. Operating parameters Application temperature In service temperature Short exposure (up to 1 h) Typical properties of cured m Cured for 5 days at 30 ± 20C, 55 Physical Properties Tensile Strength, ATM-R020 (ASTM D412) Elongation, ATM-R020 (ASTM D412) Durometer Hardness, ATM-R019 (ASTM D2240) Shear strength, ATM-R022 (ASTM D1002) MS - MS MS – ABS Chemical resistance The product is resistant to fresh water, sea water, water, motor oil, isopropanol, salt fog (95%RH), 85% Temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils. Nonalcohol, concentrated mineral acids and caustic solutions or solvents.

Additional Information:

• Delivery Time: WITHIN 3 TO 4 WEEL
• Packaging Details: 480 GM

ABOVE PRICE IS INCLUDING GST 18%.
LOCTITE 401 is a general purpose, fast curing, instant adhesive that is ideal for use on porous substrates.LOCTITE® 401 is a fast curing instant adhesive designed for the assembly of difficult-to-bond materials requiring uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. LOCTITE 401 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repairs and all types of small emergency repairs.

• Universal instant adhesive
• Very high strength on close-fitting parts
• Perfect for all quick repairs and all types of small emergency repairs.
• Bonds a wide range of similar or dissimilar substrates (metals, rubber, wood, cardboard, ceramics as well as most plastics)
• Technical Information

  Application Method	Dispense System, Manual
  Applications	Bonding Close Fitting Parts, Repairing
  Colour	Clear
  Cure Type	Moisture Cure
  Fixture Time, Steel	5.0 sec.
  Gap Fill	0.15 mm
  Key Characteristics	Fixture: Very Fast Fixture, General Purpose, Strength: High Strength, Viscosity: Low Viscosity
  Operating Temperature	-40.0 - 120.0 °C (-40.0 - 250.0 °F )
  Physical Form	Liquid
  Shear Strength, Mild Steel (grit blasted)	20.0 N/mm² (2900.0 psi )
  Substrates	Elastomer, Metal, Plastic, Porous Surface
  Technology	Cyanoacrylate
  Viscosity	100.0 mPa·s (cP)

  PRODUCTDESCRIPTION LOCTITE® 401™ provides the following product characteristics: Technology Cyanoacrylate Chemical Type Ethyl cyanoacrylate Appearance (uncured) Transparent, colorless to straw colored liquidLMS Components One part - requires no mixing Viscosity Low Cure Humidity Application Bonding Key Substrates Metals , Plastics and Elastomers This Technical Data Sheet is valid for LOCTITE® 401™ manufactured from the dates outlined in the "Manufacturing Date Reference" section.

LOCTITE® 401™ is designed for the assembly of difficultto-bond materials which require uniform stress distribution and strong tension and/or shear strength. The product provides rapid bonding of a wide range of materials, including metals, plastics and elastomers. LOCTITE® 401™ is also suited for bonding porous materials such as wood, paper, leather and fabric. NSF International Registered to NSF Category P1 for use as a sealant where there is no possibility of food contact in and around food processing areas. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification. TYPICAL PROPERTIES OF UNCURED MATERIAL Specific Gravity @ 25 °C 1.1 Flash Point - See SDS Viscosity, Cone & Plate, mPa·s (cP): Temperature: 25 °C, Shear Rate: 3,000 s -1 70 to 110LMS Viscosity, Brookfield - LVF,25°C,mPa·s (cP): Spindle 1, speed 30 rpm 100 to 120

Additional Information:

• Delivery Time: IMMEIDATE BASIS
• Packaging Details: 20 GM ONLY

ABOVE PRICE IS INCLUDING GST 18%.
SMART BOND -789 Weather Silicone Sealant TYPICAL PROPERTIES Uncured Specifific Gravity- Translucent 0.94 ± 0.02(g/ml) Specific Gravity- White/ Black/ Grey/ Ivory 1.42+-0.02(g/ml) Colors Clear, White, Black, Grey, Ivory Flow, Sag or Slump NIL Skin Formation Time (22°C / 50% R.H) 8-15min. Curing Rate (22°C / 50% R.H) 3mm / 24 hours Cured – Physical Elongation >300% Durometer Hardness, Shore A, points 20-25 Tensile Strength, N/mm2 1.8-2.4 Maximum Allowed Distortion 25% Service Temperature -50°C to +232°C DESCRIPTION SB-789 Neutral Non-Corrosive Industrial Silicone is a high performance, one component adhesive/sealant formulated for industrial and electrical applications. SB-789 remains permanently flflexible, and exhibits excellent adhesion to a wide variety ofsubstrates. SB-789 suitable for gasketing application in gear box, engine and other industrial application. Good resistance with gasoline, engine oil, gear oil & water. BENEFITS • Non-Corrosive • Neutral cure/low odor • Medium modulus • Excellent adhesion to vinyl, wood, steel, aluminum, glass and plastic • VOC Compliant • Sealing electrical equipment • Bonding appliance parts • Permanently flflexible • Waterproof Applying the Material – SB-789 Neutral Non-Corrosive Industrial Silicone is supplied ready-to-use. Under pressure it flflows readily from itscontainer. The paste-like consistency makes it easy to work; a spatula or wooden paddle can be used for tooling the surface. The cure progresses inward from the surface. At conditions of at least 72°F (22°C) and 50 percent relative humidity, the sealant forms a tack-free skin in 30 minutes. Tooling is not practical after this skin forming begins and should be completed within 5-10 minutes of application, even though this may require alternate periods of applying and tooling. Likewise, if masking tape has been used to mark offff an area, it should be removed before the skinforms.LIMITATIONS:• Applications involving prolonged sub-mersion in water, including aquariums • Surfaces that require painting • Totally confined spaces, as sealant needs atmospheric moisture for curing • Structural glazing CLEAN UP Uncured sealant can be easily removed using a solvent such as alcohol or acetone. If the sealant is cured it must be removed mechanically by cutting and scraping. CAUTION: DIRECT CONTACT OF UNCURED SEALANT IRRITATES EYES AND MAY IRRITATE SKIN. OVEREXPOSURE TO VAPOR MAY IRRITATE EYES, NOSE, AND THROAT. Avoid eye and skin contact. Use with adequate ventilation. Do not handle contact lenses with sealant on hands. IN CASE OF EYECONTACT, flush eyes with water for 15 minutes. Obtain medical attention. IN CASE OF SKIN CONTACT, remove from skin and flush with water. KEEP OUT OF THE REACH OF CHILDREN. STORAGE AND SHELF LIFE: When stored in the original unopened containers at or below 80°F (27°C), SB-789 has a shelf life of 12 months from date of manufacturing. In Countries where high heat and humidity are a factor, special precautions must be taken. Store product in a covered, well-ventilated warehouse and avoid excessive heat conditions. Storage in high heat, high humidity conditions may reduce shelf life by up to 30%. Rotation of stock is an absolute necessity. Cartons should always be stacked upright with the nozzle tip pointed upwards. DO NOT stack cartons on their side. NEVER stack cartons more than 8 high. DO NOT store within 1 meter (4 feet) of roof line of the warehouse or storage building. PACKAGING SB-789 Neutral Non-Corrosive Industrial Silicone is available in standard caulking cartridges.

Additional Information:

• Delivery Time: READY STOCK
• Packaging Details: 310 ML

ABOVE PRICE IS INCLUDING GST 18%
Anabond GP is a versatile one component acetoxy silicone sealant for sealing building joints & glazing systems. The product is excellent UV and weather resistance. Applications : Suitable for : Glass, Aluminium, Wood Stainless Steel, Polystyrene, Epoxy & Polyester Panels, Porcelain Coated Metal and uPVC. Not Suitable for : Concrete, Marble, Lead, Copper, Galvanised, Steel, PP, Teflon & Bituminous Surfaces.

Additional Information:

• Delivery Time: within 2 days
• Packaging Details: 280 ML

GST 18% INCLUDING.
Specially for Alluminium Steel section.
Description

Alusil - Black (425gm)

Alusil is suitable for interior and exterior sealing applications of all kinds of door and window joints and connection joints for aluminium, steel & wood.

Characteristics :

• For window and door professionals (aluminium, steel & wood) 
• Ideal for Indian weather conditions 
• Maximum gap filling capacity 8 mm 
• Movement capability ± 15% 
• UV resistance
•  No smell

Technical Details :

• Consistency : Paste
• Curing System : Moisture Cure
• Skin formation (20°C/65% R.H.) : Ca 20 - 30 min.
• Shrinkage (DIN 52451) : ≤15%
• Specific Gravity (DIN 53479B) : 1.45g/mL
• Temperature Resistance : -20°C to +80°C
• Maximum gap filling capacity : 8mm
• Movement capability  : ±15%

Application :

Specially designed for sealing joints in doors and windows of aluminium, steel & wood.

Shelf Life :

At least 12 months in unopened packaging in a cool and dry storage place at temperatures between +5°C and +35°.

Not Suitable For :

• Natural stone
• Structural glazing
• Mirror
• Glass to glass
• Automotive application

Joint Size :

Maximum gap filling capacity : 8 mm

Pack Content :

• 1 Cartridge (425gm)

Specifications

Additional Information:

• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 425 GM MOQ 24 NO

ABOVE PRICE INCLUDING GST 18%

PROPERTIES OF UNCURED MATERIAL
Value
Chemical type RTV Silicone
Appearance Clear, White
Specific Gravity (g/ml) 0.99
Ultimate Tensile Strength (MPa) 1.7
Elongation (%) 500
Operating Temperature
Range (Dry Service, °C) -24 to 165
Skin over time (mins)* 10-15
Tack Free time (mins)* 25 - 30
Full Cure time (hrs)* 24
Hardness (Shore A) 19
Shelf life (months) 18

Additional Information:

• Delivery Time: WITHIN 2 DAYS
• Packaging Details: 25 NO

ABOVE PRICE IS INCLUDING GST 18%

By keeping track with the modern trends, we are bringing forward a wide series of Astral Adhesives Vega Quick Instant Adhesive to our valued patrons.
Vegaquick is a general-purpose low viscosity, ethyl cyanoacrylate adhesive which is suitable for the flex board industry for bonding flex to metal or other substrates.It is recommended for bonding flex to metal or wooden surface. It is also used by industries like auto assembly shops, electronic goods repairer / manufacturer, auto mechanics & at home for general bonding applications. It bonds instantly to most plastics, rubber, ceramic, metal like non porous substrates & porous substrates like wood, leather etc. It will not bond PTFE, nylon, polypropylene etc.

• Make sure the surfaces to be bonded are clean and dry.

• Dispense a drop or drops to one surface only. Apply only enough to leave a thin film after compression.

• Press parts together and hold firmly for a few seconds. Good contact is essential. An adequate bond develops in less than one minute.

• Wipe off excess adhesive from the top of the nozzle and recap if left uncapped, may deteriorate by contamination from moisture in the air.

• Because Vegaquick condenses by polymerization, sometimes whitening will occur on the surface of the container.It will not bond PTFE, nylon, polypropylene etc.9 months from date of manufacturing. It comes without warranty as storage condition can affect the shelf life.

Additional Information:

• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 10ML,20ML,50ML

In order to cater the variegated demands of our clients, we are offering an excellent quality range of Nails Saver Instant Grab.

Details:

• RESIPRO NAIL SAVER is an instant grab adhesive with gap-filling properties that will bridge gaps up to 12mm.
• It is easy to apply, non-slump, paintable and gives strong bonds to variety of materials.
• Suitable for Interior and exterior use.

Uses:

• Ideal for fixing skirting boards, door surrounds, door frames, window sides, all types of cladding , wall patterns, decorative wall boards, metal carpet edges, automotive trims and much more.
• Adheres to brick, timber, stone, concrete, ceramics, metal, some plastics, marble and brick veneer.

Limitations:

• Do not use: In areas subject to frequent water immersion.
• On asphalt, bitumen or polystyrenene.
• As a mirror adhesive.
• On dusty or porous surfaces unless previously primed.

Applications:

• Surfaces to be bonded should be clean, dry and free from dust and grease.
• Carefully cut the tip of the cartridge, taking care not to damage the threaded area.
• Screw o n the supplied nozzle and cut at an angle of 45° to the required bead width.
• Apply using a standard sealant gun, a 6mm bead to one surface, the length of the material, and press the second surface into the bead. Apply even pressure and allow to set, as maximum bond strength may take from 12-24 hrs.
• Excess adhesive can be removed using white spirit or cellulose thinners.
• Heavy items may require temporary support whilst adhesive cures clean tools immediately after use.

Health & Safety:

• Highly flammable liquid and vapour.
• Before handling read both the product and material data sheets for detailed use and health information.
• May cause drowsiness or dizziness.
• Harmful to aquatic life with long-lasting effects.
• Keep away from heat/ sparks/ open flames/ hot surfaces.
• No smoking.
• Avoid breathing vapours.
• Use only in a well-ventilated area.
• Wear protective gloves and eye protection.
• If on skin (or hair): Remove/ take off immediately all contaminated clothing.
• Rinse skin with water/ shower.
• Call a doctor physician if you feel unwell.
• Keep out of reach of children.

 

Additional Information:

• Delivery Time: WITHIN WEEK
• Packaging Details: 60 NO AVAILABLE

GST 18 % EXTRA

WHETHER PROOF NEUTRAL PLUS (WN+)

WN+ IS THE BEST ONE PART, MID MODULUS, RTV NEUTRAL CURE SILICON RUBBER SEALANT THAT OFFERS EXCELLENT ADHESSION & WEATHERPROOF PERFORMANCE IN MULTI PURPOSE.

 

MAIN APPLICATION

USE ON BONDING, ASSEMBLY, SEALING & REPAIR FOR GLASS, COATED GLASS, ALUMINIUM PRODUCTS & VARIOUS MATERIAL JOINTS OR SEAMS.

 

PROPERTY - VALUE

Curing System - Moisture Cure

Tooling Time - Approx 10-12 min

Temperature Resistance  - (-50°C to + 100°C)

Packing/ Net Content - 25PCS/280ml

 

WHETHER PROOF NEUTRAL PLUS (WN+)

NEUTRAL CURE VERSATILE SEALANT

HIGH ADHESION & COHESION

HIGH UV RESISTANCE

LONG LIFE & FLEXIBLE

USE FOR EXTERIOR JOINTS

 

AVAILABLE: 280ml (CLEAR/ WHITE/ BLACK)

 

COLORS: BLACK /  WHITE / CLEAR

Additional Information:

• Delivery Time: WITHIN WEEK
• Packaging Details: 280 ML PACK

Being a customer oriented organization, we are deeply engaged in offering a wide array of Weather Hybrid Sealant.

Details:

• Offered sealent is a general purpose, single component thixotropic adhesive for bonding multiple substrates.
• It has excellent weatherability, compatibility, have excellent adhesion on various substrate, paintable and remain flexible when fully cured.
• It is a high quality sealant and adhesive suitable for internal & external use in all-weather condition.

Uses:

• Suitable for the installation of wall and floor panels, bonding wood, metal, glass, cement/concrete, plaster board, hard plastics, etc.
• It is ideal for use for panel fabrication, gap-filling in uPVC window profiles and concrete walls, adhering mirror, polycarbonate and
• acrylic sheet bonding with metal frame.
• Limitations: Not recommended for use for structural application and applications that will be fully immersed in water.

Applications:

• Surfaces to be bonded should be clean, dry, sound and free from dust.If required, surfaces can be cleaned prior to application using an appropriate cleaner.
• Mask adjacent surfaces with a protective tape for a neat finish and easy clean up. Carefully cut the tip of the cartridge taking care not to damage the threaded area.
• Screw on the nozzle supplied and cut to an angle of approximately 45°, to an opening slightly larger than the gap to be filled.
• Apply using a standard sealant gun.
• Extrude the sealant in to the joint, filling the cavity completely.
• Tool sealant with a wetted spatula and remove protective tape before
• sealant starts to skin.
• Sealant will begin to cure after 5 minutes, will be touch dry after 1 hour and reach full cure after 3 days (7mm depth).
• Uncured material should be removed using solvent cleaner (eg. mineral turpentine).
• Apply to a cloth and wipe.
• Cured material should be removed by sanding or trimming with a sharp blade.
• Temperature Resistance: -30° to + 80°C. Working time (at 25°C): 8-10 minutes.
• Curing time (at 25°C): 6 to 8 hours (if applied at 1 mm thickness).
• Coverage: 2 running metres per 50 ml (if applied in 5mm x 5mm bead).
• Health & Safety: Low hazard product, Before handling read both the product and material data sheets for detailed use and health information.
• Avoid contact with skin and eyes, if contact occurs, wash thoroughly with plenty of water.
• Wash hands after use.
• Do not ingest.
• Do not breathe vapours as this can irritate nose, eyes and throat.
• Use in a well ventilated space.
• Keep out of reach of children.
• This product may produce an allergic reaction.
• If irritation persists seek medical attention.

 

Additional Information:

• Delivery Time: WHTIN TWO DAS
• Packaging Details: 310 ML

RTV SILICONE SEALANT

APPERANCE :SMOOTH PASTE

COLOR : CLEAR/WHITE/BLACK

VISCOSITY : NON SAG

SKIN FORMING TIME :RT MINUTES 2-8

HARDNESS SHORE A :12 -20

Product Specification Product DescriptionIn order to retain our remarkable position in this industry, we are providing a wide array of Anabond Multiseal 102 Silicon Sealant.

Detail:

Offered sealants are acrylic based adhesives which when applied on metal-surface close-fits and upon isolation from the air, cure to form a bond. 

Additional Information:

• Production Capacity: AVAILABLE
• Delivery Time: WITHIN THREE DAYS
• Packaging Details: 280 ML PACK

500 ml pack
gst including 18% . Freight extra
product descriptionfasto chemach90 is a very high strength and fast curing two part pure epoxy based chemical anchor system. It is ready to use 3:1 cartridge. Fasto chemach90 is formulated for grouting, bonding and holding various construction substrates like steel, concrete and many other substrates. Applied in single action, this fasto chemical anchor will produce a high performance, strong fixing with exceptionally high chemical resistance.
typical applicationsfasto chemach90 is ideal for bonding and grouting fasteners, tor rods and other mechanical parts in horizontal and vertical direction. Fasto chemach90 can be used for grouting various machines, cables trays and other equipment. It is also used for holding & grouting beams, tor rods, etc
properties of cured materialvaluechemical type pure epoxyappearance greyspecific gravity 1. 4compressive strength (n/mm2) 89tensile strength (n/mm2) 31fixture time (min. ) 20full cure (hours) 24voc content (%) 0operating temperature range (°c) continuous -10 to +80
typical performance data at standard embedment depth

cure speed vs. Temperatureall figures relating to cure speed are tested at 21°c. Lower temperatures will result in slower cure. Heatingthe assembled part accelerates the curing process. Cure speed vs. Bond gapthe size of the bond gap greatly affects the speed of cureof epoxy adhesives. The larger the gap betweensurfaces, the slower the cure speed.
cure speed vs. Substrate
heat ageingfasto chemach90 retains over 90% full strength whenheated to 80°c for 90 days then cooled and tested at21°c. Cure speed and strength vary according to thesubstrates. When used on mild steel components, fastochemach90 will reach full strength more rapidly thanon more inert materials such as stainless steel. Typical environmental resistancehot strengthfasto chemach90 is suitable for use at temperaturesup to 80°c. At 80°c the bond strength will be ~75% ofthe strength of at 21°c.
chemical / solvent resistancefasto chemach90 exhibit excellent chemicalresistance to most oils and solvents including motor oil,leaded petrol, brake fluid, propanol and water. Epoxyadhesives are not recommended for use in pure oxygenand chlorine lines.

Additional Information:

• Production Capacity: AVAILABLE
• Delivery Time: IMMEIDATE
• Packaging Details: 550 ML

GST 18% EXTRA
C900 Chemical Anchor Polyester
Akfix C900 is polyester injection mortar for general purpose for solid and hollow supports having a short cure time. It is suitable for use in concrete, perforated bricks and cavity blocks in a wide range of applications.
Properties 
 

Suitable for solid and hollow structures.

High solid content.

Easy to extrude and to inject.

Thixotropic, can be applied in vertical and horizontal direction.

Fast curing.

Applications Area

Low to Medium-load applications in solid and hollow supports

Fixing of;

             Gates
             Balustrades
             Roller blinds
             Panes
             Antennas
             Consoles
             Cable trays etc

ackage
S.CodeP.CodeTypeVolumeBoxQtyB.PalletBarcodeCA035C900Polyester345 ml.12--CA030C900Polyester300 ml.12

Additional Information:

• Delivery Time: IMMEDIATE ,READY STOCK
• Packaging Details: 345 ML PACK

ABOVE RATE IS 300 ML PACKING
ABOVE RATE IS INCLUDING OF GST 18%.

Fasto S982 is a one part, low odor, oil tolerant, allweather, highly flexible, neutral cure, non corrosive, highperformance RTV Silicone sealant. It can be used forsealing, bonding and glazing applications. It is suitablefor electrical, mechanical and automotive applications.
TYPICAL APPLICATIONSFasto S982 is suitable for bonding and sealing gear box& pump flanges, air conditioning ducts, oil sumps, solarpanels, ceramics and many more electrical & mechanicalequipment and machines.It is suitable for bonding & sealing steel, aluminium,composites, glass, plastics, rubber, concrete, etc.
PROPERTIES OF UNCURED MATERIALValueChemical type RTV SiliconeAppearance Clear, White, Grey, BlackSpecific Gravity (g/ml) 1.12Ultimate Tensile Strength (MPa) 1.88Elongation (%) 350Operating TemperatureRange (Dry Service, °C) -24 to 232Skin over time (mins)* 15 - 25Tack Free time (mins)* 25 - 35Full Cure time (hrs)* 24Hardness (Shore A) 30Shelf life (months) 15
DIRECTIONS FOR USERemove all the rust, scale, dirt, dust, grease, oil, releaseagents, or other contaminants from the surfaces to bebond or seal. Surfaces can also be cleaned using suitableFasto cleaner. Apply Fasto S982 with suitable dispensingequipment. Assemble the surfaces immediately in order
to avoid skin over. Any tooling, if require, to be donebefore skin-over time. Ensure Apply S982 in sufficientquantity and wipe out the excessive quantity. Also usemasking tape to ensure aesthetically clean & neat joints.Always remove masking tape after tooling and beforeskinning of sealant.
GENERAL INFORMATIONSAFETY PRECAUTIONSAvoid breathing of vapors. Forced local exhaust isrecommended to effectively minimize exposure. NIOSHapproved, organic vapor respirators and forced exhaustare recommended in confined areas, or when conditions(such as sanding, etc) may cause high vaporconcentrations.For safe handling of this product consult the MaterialSafety Data Sheet.StorageOptimal storage conditions are between 13°C and 30°C.Storage outside this temperature range can adverselyaffect product properties and may affect the stated shelflife.Packaging300 ml cartridge and bulk packaging.LIMITATIONSThis product is not recommended for use in pure oxygenand/or oxygen rich systems and should not be selectedas a sealant against chlorine or other strong oxidizingmaterialsDATA RANGESThe data contained in this data sheet may be reportedas typical value and/or range. Values are based onactual test data and are verified on a regular basis.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 100GM & 300 ML

GST 18% INCLUDING PRICE.
DESCRIPTION ALSTONE Neutral Plus (NP-666) Silicone Sealant is a low modulus, cost effective, multi-purpose, neutral cure silicone sealant offering long term durability in a range of general sealing, general glazing, waterproofing and trade applications. Non-corrosive to concrete, brick and metals. FEATURES • Neutral cure; will not corrode metals, concrete or brick. • Good UV resistance. • Cures to a strong, flexible seal capable of withstanding movement in and around the joint. • Adheres to a range of common building materials and finishes. • Non-slumping; can be used in vertical and overhead joints. • Easy to use – one part, no mixing required. • Can be applied in any season. • Resistant to weathering, ultra-violet radiation, vibration, moisture, ozone, temperature extremes, airborne pollutants, cleaning detergents and many solvents. • Choice of colours: Clear, White and Black.
SUITABLE FOR SEALING • Brick • Concrete • Aluminium • Painted Surfaces • Glass • Ceramics • Fibreglass • Non-oily Wood etc. LIMITATIONS • Do not use for structural glazing. • Not recommended for continuous water immersion applications. • Not recommended for use with marble and similar highly porous stone finishes where sealant may affect their appearance.
• Sealant may discolour copper and brass. • Not recommended for joints where movement exceeds ±35%. • Not recommended for use in below ground joints or trafficable joints where abrasion and physical abuse are encountered. • Not recommended for use in the construction or sealing of aquariums. • Cannot be painted as paint will not adhere to sealant. • Not recommended for use on polycarbonate plastic sheeting, suitability for use on other types of plastic should be tested prior to application. • Not for use on freshly painted surfaces (enamel or solvent containing types). • Should not be applied to materials that bleed plasticisers or. • Solvents or release by-products that may inhibit its cure, affect adhesion or discolour the sealant (eg. bituminous based adhesives and coatings). • Do not clean or treat the sealant with materials, solvents or cleaning agents that may affect or discolour the sealant, particularly during sealant cure. • Do not apply at temperatures below -10°C or when substrate surface temperatures exceed +50°C. • Should not be used as an interior penetration firestop sealing system. • Should not be applied to surfaces in direct contact with food or drinking water. • Not recommended for direct contact on the reflective coatings on mirrors. • Polyester powder coat paint exhibits a highly variable wax content on the surface. Ensure thorough solvent cleaning. • Sealant cures by contact with moisture vapour in the air. • Not recommended for use in closed or confined areas where sealant cure may be inhibited by lack of air.• Not for medical or pharmaceutical use. • Do not use in the manufacture of Insulated Glass (IG) Units. • All organically extended silicone sealants exhibit higher shrinkage than 100% silicone sealants.
STORAGE AND SHELF LIFE Store in original unopened containers in a dry place. Temperature should not exceed 30°C for prolonged periods. Use sealant before stated ‘Use By’ date printed on the packaging. Previously opened cartridges may be used, provided still within the ‘Use By’ date, by simply removing any cured sealant from the nozzle. PACKAGING Supplied in standard size 300ml plastic cartridges which fit ordinary caulking guns

Additional Information:

• Delivery Time: WITHIN WEEK
• Packaging Details: 280 ML PACK

PRIC IS 18% GST INCLUDING .APPLICATIONSAlstone WS789 is netural cure, UV resistant low modulussealant for sealing expansion and control joints, precastconcrete panel joints, non structural curtainwall mullionjoints, stress cracks and joints in parapel walls.TYPICAL PROPERTIESSpecification writers: These values are not intended foruse in preparing specifications. Please contact your localAlstone sales representative prior to writing specificationson this product.Property ValueColor Black, Grey, WhiteLess than 1203-77-14non-sag25-3032-350.5NoneGood±501.31Tack-Free Time (Minutes)Curing Time (days at 25°C)Pull Adhesion (days)Flow, sag or slump (nun)Working Time (minutes)As Cured - after 7 days at 50% RH and 25” CDurometer Hardness, Shore ATensile at 150% Elongation (Mpa)StainingOzone ResistanceSpecific GravityJoint Movement Capability after 21 dayscure (%)FEATURES• All-temperature gunability, Consistency is virtuallyunchanged from -25°C to 55°C permitting thesealant to be applied in any season to dry, frostfreesurfaces.• Neutral cure - suitable for use on masonry substratesand will not react with or corrode most buildingcomponents.• Primerless adhesion - upon curing will form a strongbond to mist common building components withoutthe use of a primer.BENEFIT• Good weatherability - it is virtually unaffected bysunlight, rain, snow, ozone or temperature extremes.
• Excellent UV resistance.• Easy to use.• Bonds to most common construction materialswithout use of primer.• Excellent recovery from extension andcompression.• Ease of application - ready to use as supplied.• Compatible with all Alstone structural sealants.DESCRIPTIONAlstone WS-789 silicone weather proofing sealantis one -part neutral cure, construction gradesealant that easily extrudes in any weather. Itquickly cures at room temperature by reactionwith moisture in the air to form a durable, flexibleIt has medium modulus characteristics andexcellent unprimed-adhesion to most constructionmaterials. It is also suitable as a remedial sealantto rep lace failed organic sealants.silicone rubber seal.PREPARATIONClean all joints removing all foreign matter andcontaminants such as grease, oil, dust, water,frost, surface dirt, old sealants or glazingcompounds and protective coatings.APPLICATION METHODApply ALSTONE WS-789 silicone weatherproofingsealant in a continuous operation using a positivepressure. Tool the sealant with light pressure tospread the sealant against backing material andthe joint surfaces before a skin forms.
The applied sealant should be tooled within 25 minutes or beforea cured skin forms. Remove masking tape as soon asthe bead is tooled.HANDLING PRECAUTIONSProduct safety information required for safe use is notincluded. Before handling, read product and safetydata sheets and container labels for safe use, physicaland health hazard information. You can also obtain a copyfrom your local Alstone sales representative orDistributor.USABLE LIFE AND STORAGEWhen stored at or below 27°C ALSTONE WS-600silicone weatherproofing sealant has a shelf life ofOne year from date of manufacturing. Previouslyopened cartridges may be used within by simplyremoving the cured plug of sealant from the nozzle.Our Strengths:• Fresher product, as compared to imported brands,due to production in India.• Specially made for Indian climatic conditions.• Easy market availability throughout India.PACKAGINGCOLORSLIMITATIONSThis product is supplied in 300ml disposable plasticcartridges, 600ml sausages and bulk pails.This product is available in 18 colors: black, clear,grey and white

Additional Information:

• Production Capacity: AVAILABLE
• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 300 ML

280 ML PACK.
GST 18% EXTRA AT ACTUAL.
Technical Characteristics:
Base Modified SiliconeConsistency PasteCuring System Moisture CureSkin Formation 5 min.Curing Rate 3 mm/24hHardness 60 ± 5 Shore ASpecific Gravity 1,50 g/mlMaximum Deformation 20 %Elastic Re covery > 75 %Temperature Resistance (fully cured) -40°C to +90°CElasticity Modulus 100 % 2,30 N/ mm²Elongation at break400 %(*) these values may vary depending on environmental factors such as temperature, moisture, and type of substrates®Super-Fast AdhesiveTechnical Characteristics:Stix All is a high strength adhesive which bondsanything to anything within minutes. It has instantgrab and high load bearing capacity. It can be appliedeven on the wet surface and in under waterapplications. It is a green product with zero odor andVOC compliance.ProductCharacteristics:• High initial tack reducing the need for initial support• Fast curing, quick build-up of end strength, highsheer strength after full cure (no primer)• Easy to apply and easy to tool and finish• Remains elastic after curing• No odour• Does not contain isocyanates, silicones nor solvents• Paintable with all water based paints• Good colour stability, weather and UV resistance• Good adhesion on wet substratesApplicationsInstant fixing of ACP , Glass, Mirror, Wood, Steel, Tiles,Sanitary Ware etc with any substrate. Sealing andbonding of heavy natural stones like Marble, Granite ,Sandstone etc.
Excellent for perimeter ceiling of doors and windows,roofs, seams and cracks in bathrooms, toilets andkitchen.Sealing and bonding in the building and constructionindustry.Elastic bonding in vibrating constructions.Elastic bonding of panels, profiles and other pieces onthe most common substrates (wood, MDF, chipboard,etc).PackagingColour: white,clearPackaging: cartridge 280mlShelf life9 months in unopened packaging in a cool and drystorage place at temperatures between +5°C and+27°C.Resistance to chemical agentsGood resistance to water, aliphatic solvents, mineraloils, grease, diluted inorganic acids and alkalis Poorresistance to aromatic solvents, concentrated acids,chlorinated hydrocarbons.
SubstratesSuitable for all usual building substrates, several metalsand plastics (except PP, PE, PTFE, silicones andbituminous substrates).Surface should be clean, dry and free of dust and grease.Pre-treat the porous surfaces. In water immersedapplications surface should be primed with a suitableprimer.We recommend preliminary tests previous to application.We recommend preliminary adhesion tests previous toapplication.ApplicationMethod: Manual-or pneumatic caulking gun.Application temperature: +5°C until +45°C.Tooling: Within tooling time, before skin formation.Repair with: STIX ALL.Health and Safety RecommendationApply the usual industrial hygiene.Check the packaging for more information.Remarks• STIX-ALL may be painted, however due to the largenumber of paints and varnishes available we stronglysuggest a compatibility test before application. Thedrying time of alkyd resin based paints may increase.• STIX-ALL can be applied to a wide variety of substrates.Due to the fact that specific substrates such as plastics,polycarbonate, etc… may differ from manufacturer tomanufacturer, we recommend preliminary compatibilitytests.• While producing plastics very often releasing agents,processing aids and other protective agents (likeprotection foil) are used. These should be removedprior to bonding. For optimum adhesion the use of SurfaceActivator is recommended.• This product can not be used as a structural glazingsealant.
STIX-ALL can be used for bonding of natural stone,but it cannot be used as a joint sealant on this typeof surface. STIX-ALL Tack can therefore only be usedon the bottom of natural stone tiles.• When applying, make sure not to spill any sealant onthe surface of materials.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: WHITE/CLEAR 280 ML

ABOVE PRICE IS INCLUDING GST 18%

RESIBOND: 7010 Resibond 7010 is Red colored one part neutral cure silicone which cures to a tough rubbery solid when exposed to moisture in the air. Excellent resistance to weathering, UV light, moisture, ozone, vibration & extreme temperature. Long life reliability cured sealant stays rubbery from -35 to 310ºC without tearing, cracking, drying out or becoming brittle. All temperature Gunnability can be applied in any season. Resibond 7010 will not flow under its own weight. It can therefore be applied overhead or on vertical joints and surfaces without slumming, sagging or running out. Resibond 7010 sealant can be used for sealing terminals of heating element, oven door, gasketing, incubator, sterlising tank sealing, gasketing application where high resistance is the main requirement. Resibond 7010 sealant provides an excellent anti-corrosion barrier between dissimilar metals such as aluminum and steel where electrolytic corrosion can be severe problem, Excellent sealant for making engine head gasket to prevent leakage of oil even at higher temperature (310ºC). 1. Surface must be clean, dry & free from grease and detergents. 2. Mask adjacent surfaces for neat application. 3. Cut tip of cartridge, cut nozzle to desired size at 45 º angles, attach to cartridge, and place in caulking gun. 4. Apply sealant in continuous, steady flow. Push sealant ahead of nozzle contacting both sides of joint so it is completely filled. 5. Smooth sealant surface immediately after application before skin forms. Use spatula dipped in mild detergent. Remove masking tape before sealant skins. 6. Excess uncured sealant should be removed immediately with clean cloth damped in mineral turpentine. 7. When sealing a metal lap joint, apply sealant to one surface in a continuous bead through the line of intended fasteners and fasten immediately, if no fasteners are to be used ensure sufficient sealant is used and joint supported while sealant cures. RESIBOND 7010: Type : one part silicon rubber Cure : neutral cure at room temperature Primary use: sealant provides an excellent anti-corrosion barrier between dissimilar metals. Recommended for sealing galvanized sheet metal products. PROPERTIES: As supplied tested at 25ºC, As cured after 7 days at 25ºC, 50% relative humidity 50% relative humidity Flow, sag or slump nil Durometer hardness, shore A, points 23 Color Red Ultimate tensile strength, mpa 1.4 (14 Kg/cm2) Cure time at (days) at 25ºC 1-2 Temperature stability, ºC -35 to 310 Skin over time (min) 15 Movement capability (Elongation), percent +25 Specific.Gravity - 1.08 USAGE RATE TABLE: Approximate metres per cartridges of sealant for various joints sizes: Width in mm 1.5 3 6 9 13 16 19 25 Depth in mm 1.5 130 65 32 22 15 12 10 8 3 32 16 11 7 6 5 4 5 9.7 6.8 4.6 3.7 3 2.3 6 5.4 3.8 3 2.6 2 9 3.6 2.5 2 1.75 1.3 13 2.5 1.7 1.4 1.2 0.9 WARNING: On direct contact uncured sealant irritate eyes. Immediately flush eyes with plenty of water, contact Doctor, avoin prolongs contact of skin. Not recommended for direct food contact applications or on drinking water lines. KEEP OUT OF REACH OF CHILDREN. STORAGE/PACKING: Store below 35ºC in a dry shaded place. Use entire contents within 6 months of purchase. Available in 300 ml cartridge. Packing : 300ml

Additional Information:

• Production Capacity: AVAILABLE
• Delivery Time: IMMEDIATE
• Packaging Details: 20NO*3BOX=60 NO

ABOVE PRICE IS INCLUDING GST 18%


Backed by years of industry experience, we are engaged in offering a premium quality range of Acrylic Sealant.

Details:

• RES I PRO ACRYLIC SEALANT is an acrylic emulsion based, ready to use, one component sealant for sealing fine building joints and this can be paintable.

Uses:

• Suitable for fixing ceramic tiles, wooden mouldings etc.
• On vertical surfaces. Also ideal for use with glass, Gypsum wall boards, cured cement plaster and timber boards.Highly flexible, rapid set and non-slumping.
• Limitations: Not recommended for external use or on applications that will be fully immersed in water, not recommended for gap-filling.
• Curing gets delayed if humidity is above 50%.

Application:

• Surfaces to be bonded should be clean, dry, sound and free from dust. If required, surfaces can be cleaned prior to application using an appropriate cleaner.
• Carefully cut the tip of the cartridge taking care not to damage the threaded area.
• Screw on the nozzle supplied and cut to an angle of approximately 45°.
• Apply using a standard sealant gun.

Health & Safety:

• Low hazard product.
• Before handling read both the product and material data sheets for detailed use and health information.
• Avoid contact with skin and eyes.
• If contact occurs, wash thoroughly with plenty of water.
• Wash hands after use.
• Do not ingest.
• Do not breathe vapours as this can irritate nose, eyes and throat. Use in a well-ventilated space.
• Keep out of reach of children.
• This product may produce an allergic reaction.
• If irritation persists seek medical attention.

 

Additional Information:

• Delivery Time: WITHIN 2 DAYS
• Packaging Details: 300 ML

ABOVE PRICE IS INCLUDING OF 18% GST.

ABOVE PRODUCT PACKING 400 ML.
Technologies: Structural Adhesives

High Performance Porous Surface

Fasto MA15 is 1:1 mix ratio two component methyl methacrylate based very high strength and high performance structural adhesive. Fasto MA15 is designed to withstand higher impact load and has excellent weather resistance.  It is suitable for bonding metals, magnet, plastics, FRP and many other substrates.

Applications: AutomotiveCompressorsConstruction EquipmentHeat ExchangersMotorsPumpsStructural Bonding & SealingTractorsWhite Goods

Additional Information:

• Delivery Time: within 2 days
• Packaging Details: 50 ML & 400 ML

Technologies: Structural Adhesives

High Performance Porous Surface

Fasto MA05 is 1:1 mix ratio two component methyl methacrylate based very high strength, fast curing and high performance structural adhesive. Fasto MA15 is designed to withstand higher impact load and has excellent weather resistance.  It is suitable for bonding metals, magnet, plastics, FRP and many other substrates.
Applications: AutomotiveCompressorsConstruction EquipmentHeat ExchangersMotorsPumpsStructural Bonding & SealingWhite Goods.

Additional Information:

• Delivery Time: within 2 days

SHELF LIFE 9 MONTH
GST 18% INCLUDING .COLOR WHITE/BLACK/CLEAR
Good adhesion to most common construction substrate like concrete, metals, plastics• Good waterproof and weatherproof for interior &exterior applications• One-component sealant/adhesive• Excellent UV moisture resistance• Cures at room temperature

Additional Information:

• Delivery Time: within 2 days
• Packaging Details: Color Available Black White Clear