Lube Adhesive & Engineering Co.

Technical Information

Keeping in mind the ever-evolving needs of our clients, we are devoted towards offering an optimum quality array of Vetra MV Adhesive.

Details:

• Medium viscosity instant adhesive for bonding porous substrates (wood, cloth, etc.)

Packing: 5g, 20g

Additional Information:

• Delivery Time: within 2 days

GST EXTRA
Product Description Anabond 202 is chemically ethyl cyanoacrylate based instant bonding adhesive system. This is a single component, solvent-free, rapid-setting one part formulation which cures in seconds when pressed into a thin film between two substrates. This adhesive bonds similar and dissimilar materials and is ideally suitable for bonding of elastomeric and plastic substrates.
Advantages  Excellent adhesion to a wide variety of substrates  Very simple cure mechanism  Rapid strength development  No measuring or mixing required. Limitations  Blooming / Frosting  Difficult to cure fillet or exposed liquid adhesive without activator.  Limited gap cure  Soluble in polar solvents.  Low peel & impact strength. Properties of uncured material Viscosity at 20C, Brookfield DV-II+, ATM-R006* (ISO 2555), cPs 2 - 3 Flash point refer MSDS
Method of use Substrates must be totally free from acidic impurities or else the cyanoacrylate adhesive will not cure instantaneously. Only a very small quantity of adhesive is to be applied to achieve fastest cure and higher bond strength. Since the curing mechanism is initiated by moisture present in the atmosphere, the humidity will play a vital role during curing. Optimum bonding conditions are achieved when the relative humidity is between 40% and 60%. Cured speed Vs Different Substrates Curing performance There are many factors that can influence the rate of cure of cyanoacrylate adhesive. These include  The types of substrates being bonded  The surface conditions (Acidic or basic) of the substrates  The surface roughness of the substrates  The atmospheric conditions such as humidity, temperature etc. Properties of cured material Cured for 24 hours at 2 52 C, tested according to ATM-R022 (ASTM D1002/ISO 4597) Curing of ethyl cyanoacrylate adhesives as a function of relative humidity Storage: The product is store between 20 25C, dry place away from heat source and direct sunlight. For safe handling information on this product, consult the Material Safety Data Sheet (MSDS). Packing: This material is packed 20g Directions for use shelf life 12/6 months from the month of manufacture. Precautions 1. Use with proper ventilation. Avoid direct contact with skin and eyes. 2. If contact with skin occurs, rinse with warm water or dissolve in solvents such as acetone or nitro methane. Do not try to remove forcibly which may result in tearing of skin. 3. If adhesive gets into eye, keep eye open and rinse thoroughly. Seek medical attention immediately. 4. Keep out of reach of children. Conversions ( 0C*1. 8)+32 = 0 F kgf.m*9.81 = N.m mPa. s = cP N/mm2 * 145 = psi mm/25. 4 = inches N .m* 8. 851 = lb. in m/25. 4 = mil N.m* 0 . 738 = lb. ft Nx0. 225 = lb N .m* 0 . 142 = oz. in N/mm * 5. 71 = lb/in MPa * 145 = psi Disclaimer- Please read carefully The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user's responsibility to determine suitability for the user's purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling and use thereof. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. Anabond disclaims liability for any incidental or consequential damages of any kind, including lost profits.

Additional Information:

• Delivery Time: READY STOCK,IMMEDIATE
• Packaging Details: 20 GM

ABOVE PRICE INCLUDING GST 18%.

General purpose, low viscosity instant adhesive. Offers fast bonding on a wide range of materials.LOCTITE® 495 is a transparent, colourless, low viscosity, general purpose ethyl-based instant adhesive offering fast bonding (5-20 secs fixture time). It is able to bond a wide range of materials, including plastics, rubbers and metals. It can also bond polyolefins when used in combination with Primer LOCTITE® SF 770 or LOCTITE® SF 7239. Available in 20 g, 50 g and 500 g pack sizes.

• General purpose
• Low viscosity
• 10 - 20 secs. fixture time
• Colourless and transparent
• PRODUCT DESCRIPTION LOCTITE® 495 provides the following product characteristics: Technology Cyanoacrylate Chemical Type Ethyl cyanoacrylate Appearance (uncured) Transparent, colorless to straw colored liquidLMS Components One part - requires no mixing Viscosity Low Cure Humidity Application Bonding Key Substrates Plastics, Rubbers and Metals
• This Technical Data Sheet is valid for LOCTITE® 495 manufactured from the dates outlined in the "Manufacturing Date Reference" section. LOCTITE® 495 is a general purpose cyanoacrylate instant adhesive. Commercial Item Description A-A-3097: LOCTITE® 495 has been qualified to Commercial Item Description A-A-3097. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification. TYPICAL PROPERTIES OF UNCURED MATERIAL Specific Gravity @ 25 °C 1.1 Viscosity, Cone & Plate, mPa·s (cP): Temperature: 25 °C, Shear Rate: 3,000 s -1 20 to 45LMS Viscosity, Brookfield - LVF, 25 °C, mPa·s (cP): Spindle 1, speed 30 rpm, 20 to 60 Flash Point - See SDS TYPICAL CURING PERFORMANCE Under normal conditions, the atmospheric moisture initiates the curing process. Although full functional strength is developed in a relatively short time, curing continues for at least 24 hours before full chemical/solvent resistance is developed. Cure Speed vs. Substrate The rate of cure will depend on the substrate used. The table below shows the fixture time achieved on different materials at 22 °C / 50 % relative humidity. This is defined as the time to develop a shear strength of 0.1 N/mm².ABS <5 PVC <5 Polycarbonate 10 to 15 Phenolic <5 Cure Speed vs. Bond Gap The rate of cure will depend on the bondline gap. Thin bond lines result in high cure speeds, increasing the bond gap will decrease the rate of cure. Cure Speed vs. Humidity The rate of cure will depend on the ambient relative humidity. The best results are achieved when the relative humidity in the working environment is 40% to 60% at 22°C. Lower humidity leads to slower cure. Higher humidity accelerates it, but may impair the final strength of the bond. Cure Speed vs. Activator Where cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed. However, this can reduce ultimate strength of the bond and therefore testing is recommended to confirm effect

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 20 ML

PRODUCT DESCRIPTIONFasto FLEX FAST is a low viscosity modified Ethyl Cyanoacrylate adhesive. Fasto FLEX FAST is suitable for bonding a very wide range of materials, including some porous ones, where very fast cure speed is required.TYPICAL APPLICATIONSFasto FLEX FAST is formulated for the bonding of plastics, rubbers, wood, metals and other common substrates. Recommended for use on close-fitting parts, smooth and even surfaces.PROPERTIES OF UNCURED MATERIALValueChemical type EthylAppearance ClearSpecific Gravity 1.03Viscosity cPs1range 28 -32typical value 30Tensile Strength2 (N/mm2) 14Fixture Time (secs) 2-5Full Cure (hours) 24Operating Temperature Range (°C) -50 to +801 ISO 3104/31052 ISO 6922TYPICAL CURING PERFORMANCETypical Speed:Steel/steel <15 secondsABS/ABS <10 secondsRubber/Rubber <2 secondsCure speed vs. environmental conditionsCyanoacrylate adhesives require surface moisture on the substrates in order to initiate the curing mechanism. The speed of cure is reduced in low humidity conditions. Low temperatures will also reduce cure speed. All figures relating to cure speed are tested at 21°CCure speed vs. bond gapFasto FLEX FAST give best results on close fitting parts. The product should be applied in a very thin line in order to ensure rapid polymerisation and a strong bond. Excessive bond gaps will result in slower cure speeds. Fasto Cyanoacrylate Activators may be used to greatly increase cure speeds Cure speed vs. SubstrateThe speed of cure of Fasto FLEX FAST varies according to the substrates to be bonded. Acidic surfaces such as paper and leather will have longer cure times than most plastics and rubbers.DIRECTIONS FOR USEBonding speed is very fast so ensure that parts are properly aligned before bonding. Ensure parts are clean, dry and free from oil and grease. Product is normally hand applied from the bottle. Apply sparingly to one surface and press parts firmly together until handling strength is achieved. As a general rule, as little Cyanoacrylate as possible should be used – over application will result in slow cure speed and lower bond strength. Please contact your Fasto representative for further advice on dispensing solutions.GENERAL INFORMATIONFor safe handling of this product consult the Material Safety Data Sheet.StorageStore in a cool area and out of direct sunlight. Refrigeration to 5° C gives optimum storage stability.PackagingBottles: 20gAvailable in bulk for use with dispensing systems.DATA RANGESThe data contained in this data sheet may be reported as typical value and/or range. Values are based on actual test data and are verified on a regular basis.

Additional Information:

• Production Capacity: IMMEDIATE
• Delivery Time: WITHIN 2 DAYS
• Packaging Details: 15 GM & 20 GM & 50 GM

ABOVE PRICE IS INCLUDING GST 18%

PRODUCT : FEVIKWIK 702DESCRIPTION: FEVIKWIK 702 is a cyanoacrylate adhesive with mediumviscosity and medium setting velocity. It is widely used for bonding variety ofsubstrates and is ideally suited for bonding plastics & rubbers to each other ,metal to metal bonding or various combinations.APPLICATION AREA: This multipurpose adhesive is useful in bonding variouscomponents eg. Name plates to equipments with plastic body, assemblingplasticknobs,fixing PVC/Rubber gaskets to metal parts in filters, metaltometalbonding in various appliances etc. Recommended for use on small gaps.INSTURCTIONS FOR USE : For best results degrease / abrade and make surethe surface is clean and free from dirt, dust and contamination such as mouldreleaseagents. Apply a thin film or drop to one surface only and bring both partstogether holding firmly for a few seconds until the parts achieve handlingstrength.TYPICAL PROPERTIES:Appearance : Clear transparent liquidViscosity @ 25 o C Approx. 80 –120 Centi PoiseGap Fill : 0.15 mm approx.Flash Point : > 85 o CShelf Life : 9 months under dry and cool (<25 o C) storingcondition.Specific Gravity : 1.06 approx.Operating Temp : 40o C to +80 o CCure Speed : MetalMetal* : < 25 SecondsPlasticPlastic** : < 10 SecondsRubberRubber*** : < 5 SecondsShear Strength, M.S.M.S. : 100 Kg/cm 2 approx.Full Cure Time : 24 Hours at Room Temperature.* Mild Steel, Aluminum, Brass, etc.
** Various Plastics viz. PVC, ABS, Polypropylene, Polystyrene, Polycarbonate,Perspex etc. Primer PP2improves performance on polypropylene. It does notbond polyethylene and Teflon.*** Nitrile, Neoprene, EPDM, etc.STORAGE : Store in cool (<25 o C ) area away from sunlight, Refrigeration to 5o C gives optimum storage stability.HEALTH & SAFETY : Fevikwik 702 being a cyanoacrylate adhesive bonds skinin seconds. If accidental skin bonding occurs, wash with warm soap water andslowly pry skin apart. In case of eye contact, flush with water and seekimmediate medical treatment Accumulation of fumes in the working area shouldbe avoided by providing efficient exhaust facility. Please refer MSDS for allsafety measures. MSDS can be made available on request.

Additional Information:

• Production Capacity: immediate
• Delivery Time: within 2 days
• Packaging Details: 20 gm only

GST EXTRA AT ACTUAL.18%
BLUEFIX FLASH Bluefix Flash is a cyano acralyate adhesive which gives super fast bonding among many other super glues.   TYPICAL PROPERTIES:- Appearance    : Clear Colour less Liquid  Chemical Composition                       : Cyanoacrylate based   Area of Application:-  It is used for  quick job  bonding of  marble , granite , most plastics, and rubber components.   It is also used for general purpose woodworking furniture for quick job. It does not bond polypropylene , polyethylene, silicone  and Teflon.   Application Method:-  For best results, please ensure that surface is dry & free from moisture, dust, dirt, rust, grease & oil, etc. Surface should be degreased and abraded by using suitable emery paper. Apply BLUEFIX FLASH on the surface of one adherent in a thin film or drop and spread uniformly. Quickly bond the surface of other adherent and hold firmly for few seconds until the parts achieve sufficient handling strength.   After work is over immediately close the bottle.   Product Advantage:- Fast productivity due to fast setting  Excellent bonding. Easy applicability.  PRECAUTIONS;-  Bottle should keep close with cap, once application is over.  Store in dry and cool condition, away from direct heat, sunlight, dust and moisture. Protect from frost.  
SHELF LIFE Best to use before 9  months from the date of manufacturing.  CAUTION:-  Eye irritant and bonds skin instantly.  Avoid contact with skin and eyes.   FIRST AID:-  If skin bonding occurs, wash with soapy water or acetone based nail polish remover and carefully roll or peel skin apart. (do not pull forcefully). If comes with eye contact, wash immediately with cold water and consult eye doctor.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 20 ML & 50 ML

ABOVE PRICE IS 20GM PACK.
ABOVE PRICE IS 18% INCLUSIVE GST.
PRODUCT DESCRIPTION Fasto 701 is a high viscosity high strength medium - slow curing specially formulated modified Ethyl Cyanoacrylate adhesive gel. Fasto 701 is suitable for bonding substrate like rubber, plastics, etc. Fasto 701 offer fast & reliable curing for substrate like rubber & plastics. Due to medium to slow curing, enough time is available for surface alignment. TYPICAL APPLICATIONS Fasto 701 is formulated for the bonding of plastics, rubbers, leather & other common substrates. PROPERTIES OF UNCURED MATERIAL Chemical type Ethyl Cyanoacrylate Appearance Clear Specific Gravity 1.01 Viscosity cPs1 range 1300 - 1600 Tensile Strength2 (N/mm2) 15 Fixture Time (secs) 5 - 8 Full Cure (hours) 24 Shelf Life @ 22°C (months) 9 Max Gap Fill (mm) 0.10 Operating Temperature -30 to +80 Range (°C) 1 ISO 3104/3105 2 ISO 6922 TYPICAL CURING PERFORMANCE Typical Speed: Steel/steel <10 -15 seconds ABS/ABS <8 seconds Rubber/Rubber <8 seconds Cure speed vs. environmental conditions Cyanoacrylate adhesives require surface moisture on the substrates in order to initiate the curing mechanism. The speed of cure is reduced in low humidity conditions. Low temperatures will also reduce cure speed. All figures relating to cure speed are tested at 21°C.
Fasto 701 give best results on close fitting parts. The product should be applied in a very thin line in order to ensure rapid polymerisation and a strong bond. Excessive bond gaps / adhesive will result in slower cure speeds. Fasto Cyanoacrylate Activators may be used to greatly increase cure speeds Cure speed vs. Substrate The speed of cure of Fasto 701 varies according to the substrates to be bonded. Acidic surfaces such as paper and leather will have longer cure times than most plastics and rubbers. Some plastics with very low surface energies, such as polyethylene, polypropylene and Teflon® are difficult to bond and may require the use of suitable Fasto Cynoacrylate Activator. TYPICAL ENVIRONMENTAL RESISTANCE Hot strength Fasto 701 adhesive is suitable for use at temperatures up to 80°C. At 80°C the bond will be approximately 65% of the strength at 21°C. The bond strength at 100°C is approximately 40% of full strength at 21°C. Chemical / Solvent Resistance Fasto 701 exhibit excellent chemical resistance to most oils and solvents including motor oil, leaded petrol. Fasto 701 is not resistant to high levels of moisture or humidity over time. DIRECTIONS FOR USE Bond speed is very fast so ensure that parts are properly aligned before bonding. Ensure parts are clean, dry and free from oil and grease. Product is normally hand applied from the bottle. Apply sparingly to one surface and press parts firmly together until handling strength is achieved. As a general rule, as little Cyanoacrylate as possible should be used – over application will result in slow cure speed and lower bond strength. Please contact your Fasto representative for further advice on dispensing solutions.
Removal Of Cured Cyanoacrylate Cured Cyanoacrylate may be removed from most substrates, and parts disassembled, with Fasto CA Debonder. It is not possible to fully remove Cyanoacrylate from fabrics. Storage Store in a cool area and out of direct sunlight. Refrigeration to 5° C gives optimum storage stability. Packaging Bottles: 20g, 50 g Available in bulk for use with dispensing systems.

Additional Information:

• Delivery Time: IMEEDIATE
• Packaging Details: 20GM & 50 GM

Above price is including gst 18%

description: fevikwik gel is high viscous instant cyanoacrylate adhesive which is used to bond close fitting parts or components. It is having non – dripping and controlled flow which will have no spillage during application. Product features : • colorless • solvent less • non – dripping • controlled application • re-positionable • suitable for vertical application application area: fevikwik gel is suitable for bonding wood , metal , rubber , leather, cardboard and most plastic components. It has typical applications in molded furniture, sign boards, gift articles, besides this it is also used for wide range of industrial applications. Method of application : for best results, please ensure that surface is dry & free from moisture, dust, dirt, rust, grease & oil, etc. Surface should be degreased and abraded by using suitable emery paper. Apply fevikwik gel on the surface of one adherent in a thin film or drop and spread uniformly. Quickly bond the surface of other adherent and hold firmly for few seconds until the parts achieve sufficient handling strength. After work is over immediately close the tube / bottle.
typical properties: appearance : clear transparent liquid viscosity at 25oc : approx. 1500 centi poise flash point : > 85 oc specific gravity : 1. 06 approx.  

description: fevikwik gel is high viscous instant cyanoacrylate adhesive which is used to bond close fitting parts or components. it is having non – dripping and controlled flow which will have no spillage during application. Product features : • colorless • solvent less • non – dripping • controlled application • re-positionable • suitable for vertical application application area: fevikwik gel is suitable for bonding wood , metal , rubber , leather, cardboard and most plastic components. It has typical applications in molded furniture, sign boards, gift articles, besides this it is also used for wide range of industrial applications. Method of application : for best results, please ensure that surface is dry & free from moisture, dust, dirt, rust, grease & oil, etc. Surface should be degreased and abraded by using suitable emery paper. Apply fevikwik gel on the surface of one adherent in a thin film or drop and spread uniformly. Quickly bond the surface of other adherent and hold firmly for few seconds until the parts achieve sufficient handling strength. after work is over immediately close the tube / bottle. typical properties: appearance : clear transparent liquid viscosity at 25oc : approx. 1500 centi poise flash point : > 85 oc specific gravity : 1. 06 approx. cure speed : metal-metal* : < 20 seconds plastic-plastic** : < 10 seconds rubber-rubber*** : < 10 seconds shear strength, m. S. -m. S. : > 80 kg/sq. Cm. full cure schedule : 24 hours at ambient. Note :- there are many factors that can influence the rate of cure like types of substrates used, the condition of the surface to be bonded, the smoothness of the surface, the closeness of the surface, the atmospheric conditions etc. :2: * mild steel, aluminum, brass, etc. ** various plastics viz. Pvc, abs, polypropylene, polystyrene, polycarbonate, perspex etc. Primer pp-2 improves performance on polypropylene. it does not bond polyethylene and teflon. *** nitrile, neoprene, epdm, etc. Storage : store in cool (< 25 oc ) and dry area away from sunlight, best when stored at 2 to 8°c . Temperature less than 2°c can adversely affect product properties. Do not freeze. Keep tube/bottle tightly closed until ready for use. Shelf life : 9 months from the date of manufacture in sealed condition and dry & cool (<25 oc) storing condition.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 20 ML

GST  18% INCLUDING IN ABOVE PRICE.
THIS PRICE IS 50 GM PACK.
VETRA INSTANT ADHESIVEVetra is a single component high strength instant adhesive, used in industries like auto assembly shops,electronic goods repairer/ manufacturer, auto mechanics & in home for general bonding applications. It bondsinstantly to most plastics, rubber, ceramic, metal like non porous substrates & porous substrates like wood,leather etc. It will not bond PTFE, nylon, polypropylene etc.Vetra is available in three viscosities low, medium & Gel developed specially for porous and non poroussubstrate bonding. It bonds skin immediately so avoid contact of skin or other parts of body. In case of skinbonding do not pull apart or try to remove by rubbing use hot water or nail polish remover and remove adhesivegently. Get medical advice in case of pain or any problem occurred.METHOD OF USE:Surfaces to be bonded should be clean & dry, apply adhesive to one surface, put and position to another surfaceto be bonded over the adhesive quickly and press the bonded surfaces for few seconds to achieve perfect bond.STORAGE:Store in cool and dry place for better shelf life.Physical properties:Particulars Unit VETRA LV 401Type LVState liquidComposition Ethyl cyanoacrylateAppearance colorless liquidViscosity cps (25ºc) 15-20Setting time(Depend uponsurface to bebonded)Sec. 1-5FULL CURE H o u r 24After cureproperties:Gap filling m m 0.05Tensile shearstrengthN/mm² 15-26Servicetemperaturerange°c -40 to +90Packing 1gm, 2gm, 5gm,10gm, 20gm, 30gm,50gmSHELF LIFE:1 Year from the date of manufacturing.

Additional Information:

• Delivery Time: within 2 days
• Packaging Details: 20 GM & 50 GM

ABOVE PRICE IS INCLUDING GST 18%

General-purpose, clear, ethyl-grade instant adhesive that provides excellent bond strengths on many materials including plastics1, elastomers, metals and composites.Sicomet 100 is a fast curing medium-viscosity ethylcyanoacrylate for bonding a wide range of materials including plastics and rubbers.*Would require to be used in combination with primer for polyolefins

Additional Information:

• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 20 GM

PRICE IS INCLUSIVE 18% .

Product Specification Product DescriptionWith our expertise and trustworthiness, we are engaged in offering an optimum quality range of 0.08gm Fixwell Strong Instant Adhesive.

Additional Information:

• Production Capacity: AVAILABLE
• Delivery Time: IMMEDIATE BASIS
• Packaging Details: 0.08GM,10ML,12ML,15ML,20ML,50ML

We have marked a distinct and dynamic position in the market by providing a high quality array of Cyanoacrylate Adhesive that is instantly polymerize due to the catalytic action of moisture present on the mating surfaces. The offered adhesive is processed with the help of top grade chemicals and advanced tools, under the supervision of skilled professionals. We provide this adhesive in various specifications and deliver within the promised time - frame. Clients can avail this adhesive from us at an affordable price.

Fasto CA10is a low- viscosity,MediumStrengh modified Ethyl Cyanoacrylate adhesive. Fasto CA10 is suitable for bonding a very wide range of materials, including some porous ones, where very fast cure speed is required.Application,Plastic bonding parts,metal to metal.

Additional Information:

• Delivery Time: within 2 days

Product Specification

Additional Information:

• Delivery Time: IMMEIDIATE
• Packaging Details: 78NO*20PACKET*0.5MG=1560 NO

Cyanoacrylate Instant Adhesive are available in different specialty grades like ethyl, methyl, etc. The different grades are available in varying cure speed, strength, viscosity, etc. These best part of these adhesive is that they can form a strong bond with any combination of similar and dissimilar surfaces including rubbers, metals, plastic and more. We also provide activators and aerosol to enhance the adhesion and cure speed to form a strong bond with plastic surfaces.

POLYFIX ® Cyanoacrylate Adhesive are easy to apply either manually or automatically. Easy application and rapid cure make them perfect for high speed production. 20 gm of POLYFIX ® Cyanoacrylate Adhesive, if applied properly, can form as many as hundreds of bond.

Our Cyanoacrylate Adhesives from India have distinct advantages over other cyanoacrylates. They offer exceptional product stability and faster cure speeds. Due to their ability to adhere to a wide range of substrates, our high strength Polyfix adhesives can replace many different grades of both methyl and ethyl cyanoacrylates. Our company can provide cyanoacrylate adhesive as per the specific requirements of customers like curing speed, viscosity, blooming effect, instant Bond, instant adhesive, footwear adhesive, instant glue, cyanoacrylate glue, leather adhesive, super glue, bonding gum, pipe sealing adhesive, water based adhesive, industrial adhesive etc.Benefits

• Very Quick Setting: Sets almost in seconds with very strong bonds
• Versatile: Able to bond a wide range of assembly materials like rubbers, metals, plastics, ceramic, stones, and hard wood
• No need of heating or mixing
• Cost Saving: Due to minimal consumption our cyanoacrylate adhesive saves a lot on the cost per unit. It doesn't require mechanical fasteners, expensive clamps, jigs, nails and fittings.

Additional Information:

• Delivery Time: WITHIN 2 DAYS

DESCRIPTION: FEVIKWIK 700 is low viscous fast setting cyanoacrylate adhesive which is
used to bond close fitting parts or components. The bonding is effective due to the wicking
ability of the product.
PRODUCT FEATURES:
??? Colorless
??? Fast setting
??? Ease of application
??? Good penetration in close fitting parts.
APPLICATION AREA: FEVIKWIK 700 is suitable for bonding plastics, metal and rubber
components. It can be also used to lock components which are already assembled. It has
typical applications in molded furniture, sign boards, gift articles, besides this it is also used
for wide range of industrial applications.
METHOD OF APPLICATION:
For best results, please ensure that surface is dry & free from moisture, dust, dirt, rust,
grease & oil, etc. Surface should be degreased and abraded by using suitable emery paper.
Apply FEVIKWIK 700 on the surface of one adherent in a thin film or drop and spread
uniformly. Quickly bond the surface of other adherent and hold firmly for few seconds until the
parts achieve sufficient handling strength. After work is over immediately close the bottle.
TYPICAL PROPERTIES:
Appearance : Clear transparent liquid
Viscosity at 25oC : Approx. 1 – 5 Centi Poise
Flash Point : > 85 oC
Specific Gravity : 1.06 approx.
Operating Temp : - 40 oC to +80 oC
Gap Fill : 0.05 mm approx.
Cure Speed: Metal-Metal* : < 10 Seconds
Plastic-Plastic** : < 5 Seconds
Rubber-Rubber***: < 3 Seconds
Shear Strength, M.S.- M.S. : > 80 Kg/sq.cm.
Full Cure Schedule : 24 Hours at ambient.
* Mild Steel, Aluminum, Brass, etc.
** Various Plastics viz. PVC, ABS, Polypropylene, Polystyrene, Polycarbonate, Perspex
etc. Primer PP-2 improves performance on polypropylene. It does not bond
polyethylene and Teflon.
*** Nitrile, Neoprene, EPDM, etc.
STORAGE: Store in cool (<25 oC ) area away from sunlight, Refrigeration to 5 oC gives
optimum storage stability.
SHELF LIFE : 9 months from manufacture in sealed condition and dry and cool (<25 oC)
storing condition.
HEALTH & SAFETY : FEVIKWIK 700 being a cyanoacrylate adhesive bonds skin in
seconds. If accidental skin bonding occurs, wash with warm soap water and slowly pry skin
apart. In case of eye contact, flush with water and seek immediate medical treatment
Accumulation of fumes in the working area should be avoided by providing efficient exhaust
facility. Please refer MSDS for all safety measures. MSDS can be made available at
request.

Additional Information:

• Delivery Time: WITHIN 2 DAYS

Salient Features & Benefits :

• Fast setting, solvents, single component ready-to-use adhesive metals is required and
• Excellent bond for a variety of substrates like plastics, metals, rubber, glass and dissimilar substrates bonding of metals,
• Excellent chemical resistance

Additional Information:

• Delivery Time: within 2 days

PRICE IS INCLUDING GST 18%.
PRODUCT DESCRIPTIONFasto 555 is a low viscosity high strength very fast curing specially formulated modified Ethyl Cyanoacrylate adhesive. Fasto 555 is suitable for bonding substrate like rubber, plastics, etc. Fasto 555 offer very high speed curing for substrate like rubber & plastics.TYPICAL APPLICATIONSFasto 555 is formulated for the bonding of plastics, rubbers, leather & other common substrates.PROPERTIES OF UNCURED MATERIALChemical type EthylAppearance ClearSpecific Gravity 1.03Viscosity cPs1range 3 -5Tensile Strength2 (N/mm2) 12Fixture Time (secs) 2 - 3Full Cure (hours) 24Shelf Life @ 22°C (months) 6Max Gap Fill (mm) 0.10Operating Temperature -30 to +80Range (°C)1 ISO 3104/31052 ISO 6922TYPICAL CURING PERFORMANCETypical Speed:Steel/steel <8 -10 secondsABS/ABS <6 secondsRubber/Rubber <5 secondsCure speed vs. environmental conditionsCyanoacrylate adhesives require surface moisture on the substrates in order to initiate the curing mechanism. The speed of cure is reduced in low humidity conditions. Low temperatures will also reduce cure speed. All figures relating to cure speed are tested at 21°CCure speed vs. bond gapFasto 555 give best results on close fitting parts. The product should be applied in a very thin line in order to ensure rapid polymerisation and a strong bond. Excessive bond gaps will result in slower cure speeds. Fasto Cyanoacrylate Activators may be used to greatly increase cure speedsCure speed vs. SubstrateThe speed of cure of Fasto 555 varies according to the substrates to be bonded. Acidic surfaces such as paper and leather will have longer cure times than most plastics and rubbers. Some plastics with very low surface energies, such as polyethylene, polypropylene and Teflon® require the use of suitable Fasto Cynoacrylate Activator.TYPICAL ENVIRONMENTAL RESISTANCEHot strengthFasto 555 adhesive is suitable for use at temperatures up to 80°C. At 80°C the bond will be approximately 65% of the strength at 21°C. The bond strength at 100°C is approximately 40% of full strength at 21°C.Chemical / Solvent ResistanceFasto 555 exhibit excellent chemical resistance to most oils and solvents including motor oil, leaded petrol. Fasto 555 is not resistant to high levels of moisture or humidity over time.DIRECTIONS FOR USEBond speed is very fast so ensure that parts are properly aligned before bonding. Ensure parts are clean, dry and free from oil and grease. Product is normally hand applied from the bottle. Apply sparingly to one surface and press parts firmly together until handling strength is achieved. As a general rule, as little Cyanoacrylate as possible should be used – over application will result in slow cure speed and lower bond strength. Please contact your Fasto representative for further advice on dispensing solutions.GENERAL INFORMATIONFor safe handling of this product consult the Material Safety Data Sheet.Removal Of Cured CyanoacrylateCured Cyanoacrylate may be removed from most substrates, and parts disassembled, with Fasto CA Debonder. It is not possible to fully remove Cyanoacrylate from fabrics.StorageStore in a cool area and out of direct sunlight. Refrigeration to 5° C gives optimum storage stability.PackagingBottles: 20gAvailable in bulk for use with dispensing systems.DATA RANGESThe data contained in this data sheet may be reported as typical value and/or range. Values are based on actual test data and are verified on a regular basis.

Additional Information:

• Production Capacity: IMMEDIATE
• Delivery Time: WITHIN 2 DAYS
• Packaging Details: 20 GM & 50 GM

Above price is 18 % gst Inclusive. 20 ml pack.

 

 

 

Additional Information:

• Production Capacity: IMMEDIATE
• Delivery Time: WITHIN 2 DAYS
• Packaging Details: 20 ML & 50 ML

Product Details:

Additional Information:

• Delivery Time: within 2 days
• Packaging Details: 0.5 MG

Gst 18% including. price is 20 ml pack Freight extra.
cyanoacrylates multipurpose instant adhesivedescription lapox ultraquick is one component, solvent free, nearly instant setting and room temperature curingadhesive system. It is a tenacious adhesive, particularly when used to bond non-porous materials orthose that contain minute traces of water. It is compatible with wide range of materials like plastics,wood, metals, glass, rubber etc. It is easy to handle and dispense from convenient squeeze-tubepackaging. It is optimal for bonding small parts or assemblies and is adaptable to high speedassembly operations using automatic dispensing. Applicationsthis adhesive is useful in bonding plasticrubber, glass, wood, metals etc. ,components where instant bonding is requiredadvantagesbond forms with only contact pressure and no clamping required. Bonding to a wide variety of substrates including metals, rubbers, most plastics and ceramics. It iscost effective, as minimal amount of adhesives are needed to form strong bonds. Excellent wetting characteristics with no solvent evaporation or hazardous vapour emission. Good resistance to weathering. Ideal for high speed production, no mixing required and spread easily. No special pretreatments required for most of surfaces, rapid curing (less than a minute) at roomtemperature and no heat required. Resists many chemicals including gasoline, kerosene and variousoils. Typicalspecificationsproperties unit particularschemical type - ethyl cyanoacrylatesappearance visual clear transparent liquidcolour visual colourlesscuring - humidityspecific gravity at 25°c - 1. 04 - 1. 06viscosity m pas max 5flash point °c 84solubility - nitro methanol, acetone, dimethylformamiderefractive index - 1. 49 (± 0. 03)
after curespecificationstest unit reference valuegap fill mm - 0. 05service temperature °c - (-)55 to 82cure speed on ms - ms joint1 seconds - 20cure speed on al - al joint1 seconds - 8cure speed on acrylic - acrylic joint1 seconds - 13cure speed on pvc - pvc joint1 seconds - 4lap shear strength after 10 minutes2 kg/cm2 astm d1002 65lap shear strength after 1 hour2 kg/cm2 astm d1002 90lap shear strength after 24 hours2 kg/cm2 astm d1002 130lap shear strength3 kg/cm2 astm d1002 1001cure speed measured at 25°c on 12. 7 mm overlap area2lap shear strength on prepared ms strips at 25°c, for different cure schedule time3lap shear strength on prepared ms strips. Cure schedule, 24 hours at 30°c and 5 days at 65°c
processing surface preparation: the adherents must be thoroughly degreased with a good degreasing solvent(e. G. Toluene, acetone trichloroethylene). Abraded with coarse emery paper or chemically etchedmetal surface shows an excellent strength. Inadequately pre-treated substrates may not bondsatisfactorily. Application: apply the adhesive sparingly to one surface (usually one drop is sufficient), bring thecomponents together quickly and correctly aligned. Apply sufficient pressure to ensure the adhesivespreads into a thin film. Do not disturb or re-align until curing is achieved. Any surplus adhesive canbe removed with cleaner. For difficult or porous surfaces; activator is recommended. If bonding topolypropylene, polyethylene, ptfe or silicone surface, then prime surface first with polyolefin primer. Packaginglapox ultraquick is available in 20 ml hdpe bottles. Other packing may be considered on request. Storage and handlinglapox ultraquick should be stored in a cool and dry place, preferably in a sealed container and shouldnot be exposed to direct sunlight. This product has a shelf life of nine months, if stored in its originalcontainer between 20°c and 22°c away from humidity and excessive heat.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 20 GM & 50 GM

ABOVE PRICE IS INCLUDING GST 18%
DESCRIPTION:NeoSeal® 802 NEOFLEX is a high strength, fast setting adhesive which can be used for virtually any typeof fastening job. NeoSeal® 802 NEOFLEX has become one unique product featuring with the fastest settingability in the realm of Cyanoacrylate Adhesive. NeoSeal® 802 NEOFLEX is specially designed for bondingand repairing of wooden furniture. Better efficiency and quality combined with cost saving have madeNeoSeal® 802 NEOFLEX to be a substitute for repair material. When a thin layer of NeoSeal® 802NEOFLEX applied between two surfaces comes into contact with atmospheric moisture, a rapidpolymerization occurs producing the ultimate bond.APPLICATION:To join, fix and repair various type of flex material, ceramics, leather, wood, metal, plastic, rubber,electronics parts etc.TECHNICAL SPECIFICATIONS:No Properties Specifications1 Colour Transparent, colourless to yellowish coloured liquid2 Brookfield Viscosity 25°C 1.8 – 5 cP3 Sp. Gravity 25°C 1.14 Refractive Index (n D20) 1.4395 Vapor Pressure (hPa) < 16 Base Ethyl CyanoacrylateCURING PERFORMANCE:There are many factors that can influence the rate of cure. These include: the types of substrates used,the condition of the surface to be bonded, the smoothness of the surface, the closeness of the surfaces,the atmospheric conditions etc.1. Cure Speed / substrate:No Type of substrate Cure Speed1 Steel to Steel 5 – 10 seconds2 Stainless Steel 3 – 5 seconds3 Aluminium 5 – 15 seconds4 Zinc Plated 20 – 40 seconds5 ABS to ABS 3 – 5 seconds6 ABS to NBR 2 – 5 seconds7 ABS to Wood 5 – 10 seconds8 NBR to NBR 2 – 5 seconds9 Wood 10 – 30 seconds10 Polycarbonate 10 – 40 seconds2. Cure Speed / Humidity:The following graph shows the tensile strength developed at different levels of humidity.
3. Cure Speed / Bond Gap:The rate of cure depends on the bond-gap. A smaller bond-gap results in faster the cure speed.TYPICAL PROPERTIES OF CURED MATERIAL:Physical Properties Typical ValueColour ClearCoefficient of Thermal Expansion (K-1) 100 X 10-6Coefficient of Thermal Conductivity (W/m.K) 0.10Softening Point 165°CElectrical PropertiesVolume Resistivity (Ω.cm) 2 to 10 x 1015Surface Resistivity ((Ω) 10 to 80 x 1015Dielectric Constant at 10 kHz 2.5Dielectric Dissipation Factor at 10 kHz <0.02Dielectric Breakdown Strength (kV/mm) 25ADHESIVE PERFORMANCE:Steel Tensile Strength (After 24 hours at 25°CStainless Steel 150 – 210 Kg/cm2Aluminium 150 – 250 Kg/cm2Copper 140 – 170 Kg/cm2PVC 130 – 150 Kg/cm2ABS 40 – 60 Kg/cm2Polycarbonate 50 – 70 Kg/cm2Polystyrene 80 – 120 Kg/cm2NBR 5 – 9 Kg/cm2SBR 5 – 10 Kg/cm2NeoSeal Adhesive Pvt. Ltd.628/7 GIDC Savli, At. Manjusar, Vadodara – 391775, Gujarat, INDIAinfo@neoseal.net; Ph: +91-90999 35744; www.neoseal.netDIRECTION FOR USE:??? Make sure the surfaces to be bonded are clean and dry (preferable to solvent-wipe plastics, glass, andrubber, and to acid-treat metals).??? Dispense a drop or drops to one surface only. Apply only enough to leave a thin film after compression.??? Press parts together and hold firmly for a few seconds. Good contact is essential. An adequate bonddevelops in less than one minute. (Maximum strength is achieved in 24 to 48 hours Wipe off excess adhesive from the top of the container and recap NeoSeal® 802 NEOFLEX if leftuncapped, may deteriorate by contamination from moisture in the air.??? Because NeoSeal® 802 NEOFLEX condenses by polymerization, sometimes whitening will occur onthe surface of the container or the bonded materials. Should this happen, wipe surfaces well withacetone.PACKAGING SIZE:20 gm & 50 gmSHELF LIFE AND STORAGE:9 months from the date of manufacturing in unopened condition when store under recommended condition.Keep products in the unopened container in a cool and dry place.

Additional Information:

• Delivery Time: IMMEIDATE

ABOVE PRICE IS INCLUDING GST 18%

• High strength, Industrial grade rapid cure one component cyanoacrylate adhesive for very-fast bonding at room temperature

 

• It is widely used for bonding variety of substrates such as Wood, Metal, Plastic, Electronics, Ceramics, Rubber, Leather, Molded furniture, Sign Boards, etc.




• Clear transparent slightly thick easy to use liquid.

NeoSeal® 803 NEOQUICK is a GENERAL Industrial grade Cynoacrylate adhesive with fast setting and good flow ability. It has been specially formulated to achieve the strongest possible bond between wellmated, non-porous surfaces, such as rubber O-rings as well as other rubber and plastics parts. NeoSeal® 803 NEOQUICK is a one-component, solvent-free system and does not require the use of a catalyst, heat or clamps. When a thin layer of NeoSeal® 803 NEOQUICK applied between two surfaces comes into contact with atmospheric moisture, a rapid polymerization occurs producing the ultimate bond. APPLICATION: To join, fix and repair various type of flex material, ceramics, leather, wood, metal, plastic, rubber, electronics parts etc. TECHNICAL SPECIFICATIONS: No Properties Specifications 1 Colour Transparent, colourless to yellowish coloured liquid 2 Brookfield Viscosity 25°C 20 – 40 cP 3 Sp. Gravity 25°C 1.10 4 Refractive Index (n D20) 1.439 5 Vapor Pressure (hPa) < 1 6 Base Ethyl Cyanoacrylate CURING PERFORMANCE: There are many factors that can influence the rate of cure. These include: the types of substrates used, the condition of the surface to be bonded, the smoothness of the surface, the closeness of the surfaces, the atmospheric conditions etc. 1. Cure Speed / substrate: No Type of substrate Cure Speed 1 Steel to Steel 10 – 30 seconds 2 Stainless Steel 30 – 60 seconds 3 Aluminium 5 – 15 seconds 4 Zinc Plated 30 – 90 seconds 5 ABS to ABS 5 – 20 seconds 6 ABS to NBR 3 – 5 seconds 7 ABS to Wood 5 – 10 seconds 8 NBR to NBR 5 – 10 seconds 9 Wood 60 – 75 seconds 10 Polycarbonate 20 – 60 seconds 11 Leather 30 – 60 seconds 2. Cure Speed / Humidity: The following graph shows the tensile strength developed at different levels of humidity

Additional Information:

• Delivery Time: IMMEDIATE

DESCRIPTION: FEVIKWIK 495 is medium viscous, instant bonding multipurpose
cyanoacrylate adhesive designed to bond plastic , rubber & many other materials.
APPLICATION AREA: This adhesive is useful in bonding plastic, rubber etc.
components where instant bonding is required .eg. for Grommet fitments, molded
furnitures, plastic housing , electronic industry, fixing PVC/Rubber gaskets to metal
parts, etc.
INSTURCTIONS FOR USE : For best results degrease / abrade and make sure the
surface is clean and free from dirt, dust and contamination. Apply a thin film or drop to
one surface only and bring both parts together holding firmly for a few seconds until the
parts achieve handling strength.
TYPICAL PROPERTIES:
Sr. No. Properties Unit Typical Data.
1 Appearance -- Clear transparent liquid
2 Viscosity@ 25oC CentiPoise 40 ??50
3 Specific Gravity@ 30oC -- 1.05
4
Lap Shear Strength, ( ISO 4587 )
(After 24 hours @ 30 oC and 50 %
relative humidity approx )
Kg/cm2
MS.to MS : 85
PVC to PVC : 70
ABS to ABS : 30
5 Operating Temp oC - 50 to +80
6 Flash Point oC > 85
7 Gap Fill mm 0.10
8 Full Cure Time -- 24 Hours at at ambient condition.
pdfMachine
Is a pdf writer that produces quality PDF files with ease!
Produce quality PDF files in seconds and preserve the integrity of your original documents. Compatible across
nearly all Windows platforms, if you can print from a windows application you can use pdfMachine.
Get yours now!
FIXTURE TIME :
STORAGE & SHELF LIFE: 9 months when stored under dry and cool (<25 oC)
condition , away from direct sunlight in sealed container. Refrigeration to 5 oC gives
optimum storage stability.
HEALTH & SAFETY : FEVIKWIK 495 being a cyanoacrylate adhesive bonds skin in
seconds. If accidental skin bonding occurs, wash with warm soap water and slowly pry
skin apart. In case of eye contact, flush with water and seek immediate medical
treatment. Accumulation of fumes in the working area should be avoided by providing
efficient exhaust facility. Please refer MSDS for all safety measures.

Salient Features & Benefits :

• Fast setting, solvents, single component ready-to-use adhesive metals is required and
• Excellent bond for a variety of substrates like plastics, metals, rubber, glass and dissimilar substrates bonding of metals,
• Excellent chemical resistance

Other detail:

• It is unique in its speed and bond strength.
• It can be applied in a wide range of industrial applications. It bonds almost all materials quickly and surely.
• It is based on cyanoacrylate monomer and polymerases very quickly in presence of a minute quantity of moisture on the surface of the material to be bonded.

Salient Features & Benefits :

• Fast setting, solvents, single component ready-to-use adhesive metals is required and
• Excellent bond for a variety of substrates like plastics, metals, rubber, glass and dissimilar substrates bonding of metals,
• Excellent chemical resistance

We are ranked amongst the most trusted firms deeply engaged in offering a wide range of Fasto CA26 Cyanoacrylate Adhesive.

Other detail:

• The offered adhesive is processed by using superior quality chemical compound and sophisticated tools, under the supervision of skilled professionals.
• Apart from this, the entire range of adhesive has various features like solvent-free and non toxic.
• We offer this adhesive at pocket friendly prices and deliver within stipulated time frame.
• Fasto CA26 is a low viscosity high strength fast curing specially formulated modified Ethyl Cyanoacrylate adhesive.
• Fasto CA26 is suitable for bonding difficult to bond substrate like paper, leather etc.
• Fasto CA26 is very fast curing for substrate like rubber & plastics.

Features:

• High performance
• Rubber bonding
• Low viscosity
• Eco-friendliness
• Precise chemical composition

Additional Information:

• Item Code: Fasto-CA26

With a precise understanding of the relevant industry, we introduce ourselves as the leading manufacturer, exporter and supplier of Cyanoacrylate Adhesive.

Other detail:

• This adhesive is processed by utilizing quality approved chemical compound and latest technology in accordance with industry set guidelines.
• Our offered adhesive is tested on different quality parameters by our quality parameters.
• The entire range of adhesive is made available in various packaging options as per the requirements of our clients.
• Fasto CA15 is a very high viscosity high strength specially formulated modified ethyl cyanoacrylate adhesive for bonding metals.
• Fasto CA15 is also suitable for bonding wide range of substrates like rubbers, plastics, composites, etc.

Features:

• High performance
• Metal bonding
• High adhesiveness
• Excellent bonding strength
• Non toxic smell

Additional Information:

• Item Code: Fasto-CA15

With our in-depth knowledge of this domain, we are actively engaged in offering an excellent quality assortment of Fasto CA11 Cyanoacrylate Adhesive. 

Additional Information:

• Item Code: Fasto-CA11

We are a unique entity in this industry, actively engaged in offering a premium quality array of Fasto CA12 Cyanoacrylate Adhesive.

Additional Information:

• Item Code: Fasto-CA12

In line with clients' diverse requirements, we are involved in providing an optimum quality range of Fasto CA95 Cyanoacrylate Adhesive.

Other detail:

• Processed of world-class chemical compounds and latest technology under the supervision of highly skilled professionals, this adhesive is highly demanded in the market.
• Our offered adhesive can also be customized in order to fulfill the vast demands of the clients.
• Further, our offered adhesive can be availed by our clients at affordable prices.
• Fasto CA95 is a low-medium viscosity high strength specially formulated modified Ethyl Cyanoacrylate adhesive.
• Fasto CA95 is suitable for bonding a very wide range of materials, including some porous ones, where very fast cure speed is required.

Features:

• High performance
• High strength
• Fast curing
• High gap filling capability
• High temperature resistance

Additional Information:

• Item Code: Fasto-CA95

Including gst 18% ,freight extra 20 gm pack
multipurpose instant adhesivedescription lapox ultrafast is one component, solvent free, nearly instant setting, and room temperature curingadhesive. It is a tenacious adhesive, particularly when used to bond non-porous materials or thosethat contain minute traces of water. It is compatible with wide range of materials like plastics, wood,metals, glass, rubber etc. It is easy to handle and dispense from convenient squeeze-tube packaging. It is optimal for bonding small parts or assemblies and is adaptable to high speed assembly operationsusing automatic dispensing. Applications this adhesive is useful in bonding plastic, flex, pvc, leather, rubber, glass, metals etc. Componentswhere instant bonding is required. Advantages rapid curing (less than a minute) at room temperature and no heat requiredbond forms with only contact pressure and no clamping requiredbonding to a wide variety of substrates including metals, rubbers, most plastics and ceramicsexcellent wetting characteristics with no solvent evaporation or hazardous vapor emissiongood resistance to weatheringresists many chemicals including gasoline, kerosene & various oilsno mixing required and spread easilyno special pretreatments required for most of surfacesideal for high speed productioncost effective, as minimal amounts of adhesive are needed to form strong bondstypical properties properties unit particularschemical type - ethyl cyanoacrylatesappearance visual clear transparent liquidcolour visual colourlesscuring - humidityspecific gravity at 25°c - 1. 04 - 1. 06viscosity m pas max 5flash point °c 84solubility - nitro methanol, acetone, dimethylformamiderefractive index - 1. 49 (± 0. 03)after cure properties test unit reference valuegap fill mm - 0. 05service temperature °c - (-)55 to 82cure speed on ms - ms joint1 seconds - ≤ 8cure speed on al - al joint1 seconds - ≤ 8cure speed on acrylic - acrylic joint1 seconds - < 10cure speed on pvc - pvc joint1 seconds - < 5lap shear strength after 10 minutes2 kg/cm2 astm d1002 65lap shear strength after 1 hour2 kg/cm2 astm d1002 90lap shear strength after 24 hours2 kg/cm2 astm d1002 130lap shear strength3 kg/cm2 astm d1002 1001cure speed measured at 25°c on 12. 7 mm overlap area2lap shear strength on prepared ms strips at 25°c, for different cure schedule time3lap shear strength on prepared ms strips. Cure schedule, 24 hours at 30°c and 5 days at 65°c
processing surface preparation: the adherents must be thoroughly degreased with a good degreasing solvent(e. G. Toluene, acetone trichloroethylene). Abraded with coarse emery paper or chemically etchedmetal surface shows an excellent strength. Inadequately pre-treated substrates may not bondsatisfactorily. Application:apply the adhesive sparingly to one surface (usually one drop is sufficient), bring the componentstogether quickly and correctly aligned. Apply sufficient pressure to ensure the adhesive spreads into a thin film. Do not disturb or re-align until curing is achieved. Any surplus adhesive can be removed with cleaner. For difficult or porous surfaces activator is recommended. If bonding to polypropylene, polyethylene,ptfe or silicone surface, then prime surface first with polyolefin primer. Packaging lapox ultrafast is available in 20 ml hdpe bottles. Other packing may be considered on request. Storage and handling lapox ultrafast should be stored in a cool and dry place, preferably in a sealed container and shouldnot be exposed to direct sunlight. This product has a shelf life of nine months, if stored in its originalcontainer between 20°c and 22°c away from humidity and excessive heat. The shelf life depends onthe storage temperature. Containers should be tightly sealed when not in use. When removing anadhesive container from the refrigerator, allow the adhesive to reach room temperature before using it.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 20 GM & 50 GM PACK

GST 18% INCLUDING ABOVE PRICE.

Instant adhesives cure very quickly when confined between surfaces. Surface humidity on the substrates triggers the cure reaction which moves from the substrate surfaces towards the middle of the adhesive joint. Instant Adhesives are chosen for bonding small parts to achieve extremely fast fixturing. Due to their limited gap filling capacity they require close fitting surfaces. The adhesion to most substrates is excellent and the bonding strength in shear and tensile mode is very good.
Advantages of Fasto Instant Adhesives:

Clean and easy to apply

Very fast positioning and fixturing of parts

Free of solvents

Excellent adhesion on a wide range of substrates, Special formulations are available for bonding metals or porous substrates.

High strength on very small bond faces

Wide section of available iscosities, from wicking-grade to large gap-filling materials.

Additional Information:

• Delivery Time: WITHIN 2 DAYS
• Packaging Details: ALL PACKING AVAILABLE.