Lube Adhesive & Engineering Co.

ABOVE PRICE IS INCLUDING GST 18%
Ambient cure high viscous adhesive system Description Lapox Ultra is two component modified, viscous epoxy adhesive system. When both components are mixed in recommended ratios and cured appropriately at room temperature, an excellent bond strength can be achieved with most of the substrates including glass, metals, laminates, wood,textile and natural stones. Faster productivity can be achieved, if curing is performed at higher temperature between 40°C and 60°C. Curing at higher temperature is recommended to achieve optimum bond strength.Applications Artificial jewellery and jewel stone fixing Automobile components Ceramic works Construction Electrical components General engineering components Souvenirs and handicrafts Sports goods Advantages Adequate pot lifeExcellent electrical insulation propertiesHigh bond strengthHigh mechanical strength even in dynamic conditionsThermally stable and suitable to perform in extreme conditionsWater and chemical resistantTypical specifications Test Unit Reference ValueResin HardenerDescription - Visual Off-white, opaque,viscous liquidClear, yellowish tobrownish, viscous liquidViscosity at 25°C1 m Pas ASTM D2196 28,000 - 42,000 28,000 - 40,000Colour GS ASTM D1544 - Max 8Density g/cc ASTM D792 1.06 - 1.17 0.92 - 0.981Viscosity by Brookfield viscometerMix specifications Test Unit Reference ValueMixing ratio (resin : hardener) w/w - 100 : 80Mix viscosity at 25°C m Pas ASTM D2196 30,000 - 35,000Pot life1 Minutes ASTM D2471 75 - 90Peak exotherm temperature2 °C ASTM D2471 Max 60Surface dry* Minutes ASTM D5895 120 - 140Touch dry* Minutes ASTM D5895 300 - 320Hard dry* Minutes ASTM D5895 520 - 5401Pot life of 100 g mix mass at 25 ± 1°C in plastic disposable cup by ‘Gardco’ gel timer2Total 100 g mix mass in plastic disposable cup at 25°C*Drying time of 200 micron film on glass plate at 25°CAfter cure specifications1Lap shear strength on prepared aluminum strips after 24 hours curingTest Unit Reference ValueLap shear strength at 27°C kg/cm2 ASTM D1002 Min 120
ProcessingSurface reparation: The adherents must be thoroughly degreased with a good degreasing solvent(e.g. toluene, acetone trichloroethylene) and abraded with coarse emery paper or chemicallyetched. Inadequately pre-treated substrates may not bond satisfactorily.Application: The mixed mass is applied by brush or spatula on the surface to be adhered. The mixmust be used within its pot life.Curing: Curing normally takes place at room temperature within about 24 hours depending on theambient temperature but may be accelerated by the application of heat.PackagingLapox Ultra is available in 6.5 g, 13 g, 36 g, 90 g and 180 g tube packs as well as 450 g, 900 g and1.8 kg bottles and 9 kg, 45 kg and 90 kg HDPE carboys.Storage and handlingLapox Ultra should be stored in a cool and dry place, preferably in a sealed container and shouldnot be exposed to direct sunlight. This product has a shelf life of two years, if stored in its originalcontainer between 2°C and 40°C away from humidity and excessive heat.SafetyWear personal protective equipment (PPE). Avoid contact with the eyes and skin. In case of directcontact and irritation, it should be washed off immediately with soap and warm water. Avoidbreathing vapours, mist or gas. Please refer to the Safety Data Sheet (SDS) of Lapox Ultra fordetailed safety instructions.

Additional Information:

• Delivery Time: within week
• Packaging Details: 6.5kg,13gm,36gm,90gm,180gm

ABOVE 2 KG SET PRICE IS INCLUDING GST 18%.

Bondtite Fast & Clear is a high strength two component transparent epoxy adhesive system. These systems aretailor made to bond similar and dissimilar materials such as metal, ceramic, wood, leather, rubber, marble, glassetc. Bondtite remains unaffected to mild alkalies and acids etc, it is non toxic and electricaly insulatingAdhesive.DIRECTION FOR USE:The surface to be bonded should be degreased, cleaned roughened and moisture free. The resin and hardener aremixed in the prescribed quantities on a plate with the help of a spatula. A thin film of the mix is applied on thesurface to be bonded. The surfaces should be held together until the joints sets. (about 3 to 04 hours at roomtemperature).TYPICAL APPLICATION:Automobiles for fixing electromagnet to flywheel, bonding brake lining to brake shoe, plugging holes incylinder block, fixing head light reflector to glass, bonding metal part to miniature bulb, for liner placement inengine, for insulating high speed motor and fixing wiper on car.ELECTRICAL AND ELECTRONICS:Sealing of oil filled transformer case, fixing of magnet to metal pieces in watt hour meter, fixing aluminum capto glass shell in night bulb manufacturing, bonding of cooling coils to freezers in refrigerator, Sealing PCB,fixing diaphragm to voice coil and magnet to the base of speaker.APPLIANCES:Fixing name plate, bonding steel body to grinding stone in wet grinder, for assembly of mixer, washingmachine, gas stove, for fixing loose handle of tool, fixing of drain, hoses & sealing of tank joint in washingmachine.MISCELANEOUS:For joining of marble, wash basin pieces and repairing of chipped sanitary ware, to repair broken pictureframes, in repairing jewelry, to stick broken toy, to bond concrete chips at the back of the polished granite tile,to seal cracks in wall, for assembly of bath fitting and gate valve, as an adhesive in bangles and brasswarehandicrafts, door closure assembly, sealing of heating element & in manufacturing of sports goods like tennisracket, polo stick, shuttle cock, hockey sticks etc.TECHNICAL SPECIFICATIONSTYPEMIXINGRATIO POT LIFEAT 25°CHARDENING TIMECURING TIMEAT 25°CCOLORR : H RESIN/HARDENERBONDTITE FAST &CLEAR5 min1-1.5 hour24 hourWater clear / WaterclearBy volume 100 : 100By weight 100 : 100Viscosityat 25°C50000-70000:40000-50000AFTER CURE PROPERTIES:PROPERTIES FAST &CLEARHardness (shore D) 68-70Water Absorption(7 days at 25°C)0.15-0.18%Safe working temp. -20 to 85Chemical resistancea) Acid ExcellentB) alkalies Excellentc) Solvents-DieselExcellentDielectric propertiesa)Dielectric strength 17-19b) volume resistivity 6.8x10¹²c) Dielectric constant 4 -5Tensile shearstrength (steel tosteel) (kg/cm²)165-175PACKING:IN COLLAPSABLE TUBE IN CONTAINERFast & clear 3gm, 5gm, 7gm, 13gm, 36gm, 90gm,180gm, 270gm2kg

Additional Information:

• Delivery Time: AVAILABLE
• Packaging Details: 13GM,36GM,90GM,180GM,270GM,450GM,1.8KG

ABOVE PRICE IS INCLUDING GST 18%.

High strength white adhesive for bonding dissimilar substrates like marble, ceramic,metal, glass, wood, fibre glass etc.. Joints made with this system are 100% waterproof.Mixing ratio- 15:25 by weight100:100 by volumePot life- 25-30 min @ 25*c of 100 g mixHardening time- 3 to 4 hours @ 25*cCuring time- 24 hoursTensile strength- 155-165 kg/cm2Colour of Resin- whiteColour of Hardener- whiteColour of Mixture- whiteMETHOD FOR USE:The surface to be bonded should be cleaned and moisture free. The resin and hardener aremixed in the prescribed quantities on a plate with the help of a spatula. The surfacesshould be clamped together until the joint sets. .APPLICATIONS:- There of some major applications of it.1. For tile fixing,2. Tile grouting3. For making marble sink, temple4. Almirah and inlay work & Metal holdfast grouting on marble and concretesurface5. Bonding fibre glass to fibre glass.6. Bonding rigid PVC pipe to concrete.7. Dry Cement colors can be added.8. For making marble handicraft by using small marble pieces.9. Fixing of side grill on stair case.Packing - 16gm, 50gm, 200gm, 400gm, 2 kg

Additional Information:

• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 320 GM,1.1KG PACK

ABOVE PRICE IS INCLUDING GST 18%

Bondtite Fast & Clear is a high strength two component transparent epoxy adhesive system. These systems aretailor made to bond similar and dissimilar materials such as metal, ceramic, wood, leather, rubber, marble, glassetc. Bondtite remains unaffected to mild alkalies and acids etc, it is non toxic and electricaly insulatingAdhesive.DIRECTION FOR USE:The surface to be bonded should be degreased, cleaned roughened and moisture free. The resin and hardener aremixed in the prescribed quantities on a plate with the help of a spatula. A thin film of the mix is applied on thesurface to be bonded. The surfaces should be held together until the joints sets. (about 3 to 04 hours at roomtemperature).TYPICAL APPLICATION:Automobiles for fixing electromagnet to flywheel, bonding brake lining to brake shoe, plugging holes incylinder block, fixing head light reflector to glass, bonding metal part to miniature bulb, for liner placement inengine, for insulating high speed motor and fixing wiper on car.ELECTRICAL AND ELECTRONICS:Sealing of oil filled transformer case, fixing of magnet to metal pieces in watt hour meter, fixing aluminum capto glass shell in night bulb manufacturing, bonding of cooling coils to freezers in refrigerator, Sealing PCB,fixing diaphragm to voice coil and magnet to the base of speaker.APPLIANCES:Fixing name plate, bonding steel body to grinding stone in wet grinder, for assembly of mixer, washingmachine, gas stove, for fixing loose handle of tool, fixing of drain, hoses & sealing of tank joint in washingmachine.MISCELANEOUS:For joining of marble, wash basin pieces and repairing of chipped sanitary ware, to repair broken pictureframes, in repairing jewelry, to stick broken toy, to bond concrete chips at the back of the polished granite tile,to seal cracks in wall, for assembly of bath fitting and gate valve, as an adhesive in bangles and brasswarehandicrafts, door closure assembly, sealing of heating element & in manufacturing of sports goods like tennisracket, polo stick, shuttle cock, hockey sticks etc.TECHNICAL SPECIFICATIONSTYPEMIXINGRATIO POT LIFEAT 25°CHARDENING TIMECURING TIMEAT 25°CCOLORR : H RESIN/HARDENERBONDTITE FAST &CLEAR5 min1-1.5 hour24 hourWater clear / WaterclearBy volume 100 : 100By weight 100 : 100Viscosityat 25°C50000-70000:40000-50000AFTER CURE PROPERTIES:PROPERTIES FAST &CLEARHardness (shore D) 68-70Water Absorption(7 days at 25°C)0.15-0.18%Safe working temp. -20 to 85Chemical resistancea) Acid ExcellentB) alkalies Excellentc) Solvents-DieselExcellentDielectric propertiesa)Dielectric strength 17-19b) volume resistivity 6.8x10¹²c) Dielectric constant 4 -5Tensile shearstrength (steel tosteel) (kg/cm²)165-175PACKING:IN COLLAPSABLE TUBE IN CONTAINERFast & clear 3gm, 5gm, 7gm, 13gm, 36gm, 90gm,180gm, 270gm2kg

Additional Information:

• Delivery Time: AVAILABLE
• Packaging Details: 13GM,36GM,90GM,180GM,270GM,450GM,1.8 KG,5:4 KG

ABOVE PRICE IS INCLUDING GST 18%

BONDTITE SUPER STRENGTH
HIGH STRENGTH EPOXY ADHESIVE
Bondtite Super Strength is a high strength two component epoxy adhesive system. These systems are tailor
made to bond similar and dissimilar materials such as metal, ceramic, wood, leather, rubber, marble, glass etc.
Bondtite remains unaffected to mild alkalies and acids etc, it is non toxic and electricaly insulating Adhesive.
DIRECTION FOR USE:
The surface to be bonded should be degreased, cleaned roughened and moisture free. The resin and hardener are
mixed in the prescribed quantities on a plate with the help of a spatula. A thin film of the mix is applied on the
surface to be bonded. The surfaces should be held together until the joints sets. (about 8 to 10 hours at room
temperature).
TECHNICAL SPECIFICATIONS
TYPE MIXING
RATIO
R : H
POT LIFE AT
25°C
HARDENING
TIME
CURING
TIME AT 25°C
COLOR
RESIN/HARDENER
BONDTITE
Super Strength
Milky / yellowish
By volume 100 : 100 60 min 6-8 hours 24 hours
By weight 100 : 80
Viscosity at
25°C (in cps)
45000-55000:
40000-50000
AFTER CURE PROPERTIES:
PROPERTIES Super Strength
Hardness (shore D) 80-85
Water Absorption
(7 days at 25°C)
0.12-0.15%
Safe working temp. -20 to 100
Chemical resistance
a) Acid Excellent
B) alkalies Excellent
c) Solvents-
Diesel
Excellent
Dielectric properties
a)Dielectric strength 18-20
b) volume resistivity 6.8x10¹²
c) Dielectric constant 4 -5
Tensile shear
strength (steel to
steel) (kg/cm²)
190-210
TYPICAL APPLICATION:
Automobiles for fixing electromagnet to flywheel, bonding brake lining to brake shoe, plugging holes in
cylinder block, fixing head light reflector to glass, bonding metal part to miniature bulb, for linear placement in
engine, for insulating high speed motor and fixing wiper on car.
ELECTRICAL AND ELECTRONICS:
Sealing of oil filled transformer case, fixing of magnet to metal pieces in watt hour meter, fixing aluminum cap
to glass shell in night bulb manufacturing, bonding of cooling coils to freezers in refrigerator, Sealing PCB,
fixing diaphragm to voice coil and magnet to the base of speaker.
APPLIANCES:
Fixing name plate, bonding steel body to grinding stone in wet grinder, for assembly of mixer, washing
machine, gas stove, for fixing loose handle of tool, fixing of drain, hoses & sealing of tank joint in washing
machine.
MISCELANEOUS:
For joining of marble, wash basin pieces and repairing of chipped sanitary ware, to repair broken picture
frames, in repairing jewelry, to stick broken toy, to bond concrete chips at the back of the polished granite tile,
to seal cracks in wall, for assembly of bath fitting and gate valve, as an adhesive in bangles and brassware
handicrafts, door closure assembly, sealing of heating element & in manufacturing of sports goods like tennis
racket, polo stick, shuttle cock, hockey sticks etc.
SHELF LIFE: 12 Months

Additional Information:

• Delivery Time: WITHIN 2 DAYS
• Packaging Details: All Packing

ABOVE PRICE IS INCLUDING GST 18%

Product chemical familyformulated bisphenol-a epoxy resin. Chemical nameepoxy resinchemical namecas-no. Concentration [%]bisphenol a-(epichlorhydrin); epoxy resin25068-38-670-80irritating to eyes and skin. May cause sensitization by skin contacttoxic to aquatic organism, may cause long term adverse effects in the aquatic environment. First aid for eyes:flush eye with clean water for at least 15 minutes. If eye irritation persists, consult a specialist. First aid for skin:immediately remove contaminated clothing and excess contaminant. Flush skin with water. Wash thoroughly with soap and warm water. Consult a physician if irritation develops. First aid for ingestion:do not induce vomiting. Give two glass of water to dilute if patient is conscious. First aid of inhalation:move to fresh air. Call a physician immediately1. Identification of the product5. Fire fighting measures2. Composition / information of ingredients3. Hazards identification4. First aid measuressafety data sheetbondtite electrical & electronics . . . . . . Version no. : 03 date: 01/10/16page 2 of 12extinguishing media:water carbon dioxide dry chemical foam alcohol foamextinguishing media which must not be used for safety reason:high volume water jetspecial protective equipment for firefighter:wear self contained breathing apparatus and protective suit. Hazardous products of combustion:when heated to decomposition it emits fumes of cl- , carbon monoxide, other fumes and vapors varying in composition and toxicity. Personal protection:keep away from source of ignition-no smokingavoid contact to skin, eyes and clothing. Do not breathe vapour/dustenvironmental precaution:prevent spill from entering drains. Do not contaminate surface water. Avoid subsoil penetrationmethod of cleaning:for large spills, pump to storage/salvage vessels. Soak up residue with an absorbent such as clay, sand, or other suitable material and dispose of properly. Flush area with water to remove trace residue. Handling :handling precautions:provide sufficient air exchange and/or exhaust in work rooms. Handle and open container with care. Storage:keep away from food drink and animal feeding stuff. Keep container tightly closed. Keep temperature between 2-40 cstorage class 10, environmentally hazardous liquid. Engineering controlsno special precaution requiredpersonal protective equipmenteye and face protection:safety glasses with side shields. Skin protection:6. Accidental release measures7. Handling and storage8. Exposure controls/ personal protectionsafety data sheetbondtite electrical & electronics . . . . . . Version no. : 03 date: 01/10/16page 3 of 12chemical-resistant gloves and other gear as required to prevent skin contact. Long sleeved clothing. Respiratory protection:in case of insufficient ventilation wear suitable respiratory equipment. Filter type ax p2 (organic vapors, particles)hygiene measures:keep away from food drink and animal feeding stuff. Wash hand before brakes and immediately after handling the product. Protective measure:keep away from source of ignition-no smokingavoid contact to skin, eyes and clothing. Appearance : opaque. Physical state : viscous liquid. Color : milky whiteviscosity @ 25oc : 55000-65000 cpsconditions to avoid:take necessary action to avoid static electricity discharge. Material to avoid:strong acids and strong basesstrong oxidizing agents. Hazardous products of decomposition:oxides of carbon; aldehydes, acids and other organic substances may be formed during combustion or elevated temperature (>500 deg f) degradation. Conditions under which hazardous polymerization may occur:heat is generated when resin is mixed with curing agents; run-a-way cure reactions may char and decompose the resin, generating unidentified fumes and vapors which may be toxic. Acute oral effects:oral ld 50 rat dose: > 5000mg/kgeye irritation:irritatingrabbitskin irritation:irritating10. Stability / reactivity

Additional Information:

• Delivery Time: within 2 days
• Packaging Details: 1.8 KG & 5.4 KG

ABOVE PRICE IS INCLUDING GST 18%

TECHNICAL DATASHEETPRODUCT : BLUEFIX- ACEDESCRIPTION: BLUEFIX ACE is a two component epoxy adhesive that bonds virtually anything to anything from tiny parts to large structural components. This multipurpose two component system comprises of Epoxy resin and Polyamide hardener which are to be mixed thoroughly in the recommended ratio to achieve optimum results. BLUEFIX ACE is a thermosetting system which means, the resin and hardener on mixing cure by polymerization to a rigid thermoset mass which on heating may soften but shall not melt and flow. This system does not contain volatile matter such as solvent or water and hence there is negligible shrinkage on curing. BLUEFIX ACE which is internally flexiblized system provides strong joints with excellent low creep properties hence, make it ideal for structural bonding applications.PRODUCT FEATURES:??? FAST SETTING - Handling strength is achieved within 4 hours.??? Excellent adhesion to a wide range of substrates, virtually anything to anything. These substrates include all natural wood, Plywood and engineered wood such as MDF, Particle board which could be used in Cabinet frame making along with other substrates, Metals, Metal alloys, Ferrous/non Ferrous castings, China ware, Ceramics, Glass, Marble, Granite, Kadappa, Variety of Artificial Stones, Leather, Hardboard, Cement-Concrete, Most Plastics viz. Rigid PVC, Filled/unfilled ABS, Polystyrene, Epoxy/Polyester FRP, Polycarbonate, Phenol-Formaldehyde (Bakelite) moulded parts, decorative /Industrial Laminates, Powder coated metal, Asbestos, Cork, Ferrite, etc. Please note that Plastics like PTFE, Polyethylene, Polypropylene cannot be bonded without appropriate specialized surface treatment to these surfaces Non-sagging nature helps in vertical applications High Cohesive Strength Good solvent/Chemical resistance Negligible shrinkage on curing and hence good dimensional stability Good shock resistance Long lasting bondAPPLICATION AREA:BLUEFIX ACE is a multipurpose structural adhesive finding extensive applications in virtually all industries. These applications could be in OEM, Wood Working Joinery or Maintenance. This system is an indispensable tool for engineers and proved its value in thousands of applications in Wood Working, Automobile, Electronics, Electrical, Railway, Aeronautical, Construction and host of engineering industry.
GENERAL INSTRUCTIONS FOR USE:1. Substrate Preparation : The strength and durability of bonded joint are dependent on proper pre-treatment of substrates to be bonded. At the very least surfaces to be joined should be cleaned with a good degreasing agent such as Acetone or Trichloroethylene in order to remove all traces of oil, grease, rust, dust, etc. from the surface. The best and most durable joints are obtained by either mechanical abrading (Sand Blasting) or by chemical etching (pickling) the degreased surfaces. Mechanical abrading shall be followed by a second degreasing treatment.2. Mixing of RESIN and HARDENER : Epoxy resin should be thoroughly mixed with Hardener .MIX RATIOPARTS BY WEIGHTPARTS BY VOLUMERESIN100100HARDENER80100Resin and Hardener are to be mixed until they form a homogeneous mix. It is very important that the above proportions are adhered as accurately as possible to achieve optimum results. Do not mix on high-speed mixer, which will result in sudden increase in temperature, which shall adversely affect the pot-life of the mix. Mix, at a time, small quantity so that it can be consumed in stipulated usable life. 50 gms of mixture of BLUEFIX ACE has a usable life of about 60 minutes at 30°C of room temperature.Note: Specialized Automatic Metering & Mix equipment are available in the market. These equipment help to improve the productivity and reliability.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 1.8 KG PACK

ABOVE PRICE IS INCLUDING OF GST  18%.

A strong, solvent-free adhesive suitable for all materials, ideal for durable bonding and repairs. Perfect for complicated jobs which require adjustment thanks to a long working time.

Important
Bonds metal, wood, masonry, ceramics, glass, dry concrete, chipboard, leather, cardboard, fabric, rubber and most plastics (except polyethylene, polypropylene, Teflon®).
Make sure surfaces are clean and free from dust, corrosion, dirt and grease. For optimum bonding, slightly roughen surfaces with sandpaper and degrease metals with a suitable solvent. During assembly apply light pressure to the joint until set (clamps, tape) around 8 hours. Allow 14 hours to attain full strength before rough handling or sanding.

How to apply
Araldite® Standard is a strong 2-component epoxy with long working time. Parts repositionable for 80 minutes. Oil, chemical and impact resistant. High temperature resistance (-30°C to 65°C). Withstands rough handling. Do not use to repair or bond items that will contact food or drink. Not recommended for bonding rear-view mirrors to car windscreens.

Storage
Should be stored in a dry place at room temperature in the original tubes.

 

New
Environmentally friendly product formulation plus eco-friendly packaging for easy recycling.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 5M,13GM,36GM,90GM180GM,270GM,450GM,700GM,

GST INCLUDING 18%
ARALDITE® AW 106 Resin Hardener HV 953U MULTI-PURPOSE EPOXY ADHESIVE DESCRIPTION: Araldite AW 106 resin/Hardener HV 953U epoxy adhesive is a multi-purpose, viscous material that is suitable for bonding a variety of materials including metal, ceramic, and wood. The electrically insulating adhesive is easy to apply either manually by spatula and stiff brush or mechanically with meter/mix and coating equipment. Araldite AW 106 resin/Hardener HV 953U epoxy adhesive cures at temperatures from 68ºF (20ºC) to 356ºF (180ºC) with no release of volatile constituents. APPLICATIONS: • Metal • Ceramics • Wood • Vulcanized Rubber • Foams • Plastics ADVANTAGES: • Long open time • High shear and peel strength • Easy to apply • Good resistance to static and dynamic loads • Electrically insulating TYPICAL Test Values(1) PROPERTIES: Property Test Method Resin Hardener Color/appearance Visual Creamy, viscous/liquid Amber Liquid Specific Gravity ASTM D-792 1.17 0.92 Viscosity (cP) @ 77°F (25°C) ASTM D-2393 50,000 35,000 TYPICAL MIXED Property Test Method Test Values(1) PROPERTIES: Reaction Ratio (by weight) 100R/80H Reaction Ratio (by volume) 100R/100H Pot Life, hours @ 77°F (25°C) ASTM D-2471 2 (4.fl. oz. mass) Mixed viscosity (cP) @ 77°F (25°C) ASTM D-2393 45,000 1 Tested @ 77°F (25°C) RECOMMENDED Temperature Handling Strength Minimum Cure Time CURE SCHEDULES: 68ºF (20ºC) 12 hours 15 hours 77ºF(25ºC) 7 hours 12 hours 104ºF (40ºC) 2 hours 3 hours 158ºF (70ºC) 30 minutes 50 minutes 212ºF (100ºC) 6 minutes 10 minutes 302ºF (150ºC) 4 minutes 5 minutes TYPICAL CURED Application of Adhesive PROPERTIES: The resin/hardener mix is applied with a spatula to the pretreated and dry joint surfaces. A layer of adhesive 0.002 to 0.004-inches (0.05 to 0.10-mm) thick will normally impart the greatest lap shear strength to a joint. The joint components should be assembled and clamped as soon as the adhesive has been applied. Even contact throughout suffices to ensure proper cure. Standard Test Specimens Unless otherwise stated, the figures given below were all determined by testing standard specimens made up by lap-jointing 4-inch x 1-inch x 0.06- inch (10-cm x 2.5-cm x 1.5-mm) strips of aluminum. The joint area was 0.5 x 1 inch (12.5 mm x 2.5 cm) in each case.

Additional Information:

• Delivery Time: WITHIN 2 DAYS

ABOVE PRICE IS INCLUDING GST 18%
Araldite® AV 138M-1 / Hardener HV 998-1 Two component epoxy adhesive Key properties • Excellent chemical resistance • Temperature resistant to 140°C • Thixotropic, gap filling paste Description Araldite® AV 138M-1 / Hardener HV 998-1 is a two component, room temperature curing paste adhesive of high strength. When fully cured the adhesive will have excellent performance at elevated temperatures and has high chemical resistance. It is suitable for bonding a wide variety of metals, ceramics, glass, rubbers, rigid plastics and other materials, and is widely used in many industrial applications where resistance to aggressive or warm environments are required. Typical product data Property Araldite® AV 138M-1 Hardener HV 998-1 Mix Colour - visual (A112)* beige grey grey Specific gravity ca. 1.7 ca. 1.6 ca. 1.7 Viscosity (Pas) thixotropic thixotropic thixotropic Lap shear strength at 25°C (A501)* - - > 11 MPa Pot Life (100 gm at 25°C) - - 30 min * Specified data are on a regular basis analysed. Data which is described in this document as 'typical' is not analysed on a regular basis and is given for information purposes only. Data values are not guaranteed or warranted unless if specifically mentioned. Processing Pretreatment The strength and durability of a bonded joint are dependant on proper treatment of the surfaces to be bonded. At the very least, joint surfaces should be cleaned with a good degreasing agent such as acetone or other proprietary degreasing agents in order to remove all traces of oil, grease and dirt. Low grade alcohol, gasoline (petrol) or paint thinners should never be used. The strongest and most durable joints are obtained by either mechanically abrading or chemically etching (“pickling”) the degreased surfaces. Abrading should be followed by a second degreasing treatment Mix ratio Parts by weight Parts by volume Araldite® AV 138M-1 100 100 Hardener HV 998-1 40 40.

Application of adhesive The resin/hardener mix is applied with a spatula, to the pretreated and dry joint surfaces. A layer of adhesive 0.05 to 0.10 mm thick will normally impart the greatest lap shear strength to the joint. The joint components should be assembled and clamped as soon as the adhesive has been applied. An even contact pressure throughout the joint area will ensure optimum cure. Mechanical processing Specialist firms have developed metering, mixing and spreading equipment that enables the bulk processing of adhesive. We will be pleased to advise customers on the choice of equipment for their particular needs. Equipment maintenance All tools should be cleaned with hot water and soap before adhesives residues have had time to cure. The removal of cured residues is a difficult and time-consuming operation. If solvents such as acetone are used for cleaning, operatives should take the appropriate precautions and, in addition, avoid skin and eye contact. Typical times to minimum shear strength Temperature °C 10 15 23 40 60 100 Time to reach a LSS hours 14 8 4 - of 1 MPa minutes 75 20 4 Time to reach a LSS hours 22 15 6 of 10 MPa minutes 120 30 5 LSS = Lap shear strength. Typical cured properties Unless otherwise stated, the figures given below were all determined by testing standard specimens made by lapjointing 114 x 25 x 1.6 mm strips of aluminium alloy. The joint area was 12.5 x 25 mm in each case. The figures were determined with typical production batches using standard testing methods. They are provided solely as technical information and do not constitute a product specification.

Additional Information:

• Delivery Time: WITHIN SEVEN DAYS
• Packaging Details: 1.400 KG

above rate is including of 18% gst.
technical datasheetproduct : bluefix- super strongdescription: bluefix super strong is a two component epoxy adhesive that bondsvirtually anything to anything from tiny parts to large structural components. This multipurposetwo component system comprises of epoxy resin and polyamide hardener which are to bemixed thoroughly in the recommended ratio to achieve optimum results. Bluefix superstrong is a thermosetting system which means, the resin and hardener on mixing cure bypolymerization to a rigid thermoset mass which on heating may soften but shall not melt andflow. This system does not contain volatile matter such as solvent or water and hence there isnegligible shrinkage on curing. Bluefix super strong which is internally flexiblized systemprovides strong joints with excellent low creep properties hence, make it ideal for structuralbonding applications. Product features fast setting - handling strength is achieved within 4 hours excellent adhesion to a wide range of substrates, virtually anything to anything. Thesesubstrates include all natural wood, plywood and engineered wood such as mdf, particleboard which could be used in cabinet frame making along with other substrates, metals,metal alloys, ferrous/non ferrous castings, china ware, ceramics, glass, marble, granite,kadappa, variety of artificial stones, leather, hardboard, cement-concrete, most plasticsviz. Rigid pvc, filled/unfilled abs, polystyrene, epoxy/polyester frp, polycarbonate, phenol-formaldehyde (bakelite) moulded parts, decorative /industrial laminates, powder coatedmetal, asbestos, cork, ferrite, etc. Please note that plastics like ptfe, polyethylene,polypropylene cannot be bonded without appropriate specialized surface treatment tothese surfaces. Non-sagging nature helps in vertical applications high cohesive strength good solvent/chemical resistance negligible shrinkage on curing and hence good dimensional stability. Good shock resistancelong lasting bondapplication area:bluefixsuper strong is a multipurpose structural adhesive finding extensive applications invirtually all industries. These applications could be in oem, wood working joinery ormaintenance. This system is an indispensable tool for engineers and proved its value inthousands of applications in wood working, automobile, electronics, electrical, railway,aeronautical, construction and host of engineering industry. General instructions for use:1. Substrate preparation : the strength and durability of bonded joint are dependent onproper pre-treatment of substrates to be bonded. At the very least surfaces to be joinedshould be cleaned with a good degreasing agent such as acetone or trichloroethylene inorder to remove all traces of oil, grease, rust, dust, etc. From the surface. The best and mostdurable joints are obtained by either mechanical abrading (sand blasting) or by chemicaletching (pickling) the degreased surfaces. Mechanical abrading shall be followed by asecond degreasing treatment. 2. Mixing of resin and hardener : epoxy resin should be thoroughly mixed withhardener . Mix ratio parts by weight parts by volumeresin 100 100hardener 80 100resin and hardener are to be mixed until they form a homogeneous mix. It is very importantthat the above proportions are adhered as accurately as possible to achieve optimum results. Do not mix on high-speed mixer, which will result in sudden increase in temperature, whichshall adversely affect the pot-life of the mix. Mix, at a time, small quantity so that it can beconsumed in stipulated usable life. 50 gms of mixture of bluefix super strong has a usablelife of about 60 minutes at 30°c of room temperature. Note: specialized automatic metering & mix equipment are available in the market. Theseequipment help to improve the productivity and reliability.

Additional Information:

• Delivery Time: within 2 days
• Packaging Details: BOX PACKING ( GST EXTRA)

ABOVE PRICE IS INCLUDING GST 18%.
Ambient cure high viscous adhesive systemDescription Lapox Ultrafix is two component, multi-functional, fast setting and high strength versatileconstruction, epoxy adhesive system. This is used for spot bonding of large stone and tiles onvertical surfaces and has high mechanical strength as well as outstanding resistance to water andchemicals. Lapox Ultrafix resin and hardener are to be mixed thoroughly in the recommended mixingratio to achieve optimum results.Applications Adhesive for bedding marbleGranite and other stone on wallsAnchoring grouts for reinforcing steelBonding of fabricated componentsRepairing material for concrete cracksSpot bonding for marbles and granites on concrete surfacesAdvantages Allows plumb level adjustments while the stone is in placeFast curing (handling strength within 60 minutes to 90 minutes)Faster productivity due to rapid curingHigh bond strength on damp surfacesOut-standing resistance to water and chemicalsReduction in labor costSetting of clampsDrilling and cutting of stone is not requiredTypical specifications1Viscosity by Brookfield viscometerTest Unit ReferenceValueResin HardenerDescription - Visual Thixotropic white paste Thixotropic white pasteViscosity at 25°C1 m Pas ASTM D2196 2,00,000 - 3,00,000 2,00,000 - 3,00,000Colour - Visual Off-white Off-whiteDensity g/cc ASTM D792 1.55 - 1.65 1.55 - 1.65Mix specifications Test Unit Reference ValueMixing ratio (resin : hardener) w/w - 100 : 50Mixing ratio (resin : hardener) v/v - 2 : 1Pot life1 Minutes ASTM D2471 10 - 15Peak exotherm temperature2 °C ASTM D2471 Max 771Pot life of 100 g mix mass at 25 ± 1°C in plastic disposable cup by ‘Gardco’ gel timer2Total 100 g mix mass in plastic disposable cup at 25°C
After cure specifications Test Unit Reference ValueLap shear strength after 24 hours1 kg/cm2 ASTM D1002 Min 120Lap shear strength after 24 hours(curing under water)1 kg/cm2 ASTM D1002 Min 50Flexural strength2 kg/cm2 ASTM D796 Min 400Tensile strength2 kg/cm2 ASTM D638 Min 250Compressive strength after 6 hours3 kg/cm2 ASTM D695 Min 290Compressive strength after 7 days3 kg/cm2 ASTM D695 Min 400Sag resistance test at 25°C - - No saggingSag resistance test at 45°C - - No saggingHardness4 Shore - D ASTM D2240 Min 80Water absorption (after 24 hours) % ASTM D670 - 63 Max 0.5Pull of Adhesion5 psi ASTM D4541 Min 2000Coverage on Marble/Granite substrateat 1.5mm thickness6 ft2/kg - 8.5 - 9.51Lap shear strength on prepared aluminum strips at 25°C2Flexural and tensile strength after 24 hours curing at 25°C3Compressive strength at 25°C4Hardness checked after 24 hours for 45 g mix mass at 25°C5Pull of adhesion on granite/marble substrate6Actual coverage will vary depending on job site conditions, surface, thickness etc. Add 10 - 20% for waste, spillage and clean-upProcessing Surface preparation:All substrates must be clean and dry prior to application of Lapox Ultrafix adhesive system.Clean and grind the area of stone where Lapox Ultrafix is to be used by using mechanical wheelgrinder with a diamond wheel blade.Surface after treatment must be thoroughly cleaned of all laitance, loose material, oil and grease.Application:Stir part A (resin) and part B (hardener) thoroughly with separate stirrer to get uniform mix mass.Take part A and B in proportion of 100 : 50 (by weight) and mix thoroughly until, homogeneous pastewith uniform colour is achieved, with putty knife or margin travel.Apply immediate and evenly distribute on the back of the tile and stone.Apply minimum five days, one in each corner and other in center, dap thickness must be maintain 3mm.The mix mass must be used within its pot life.Curing: Curing normally takes place at room temperature within about 24 hours depending on theambient temperature but may be accelerated by the application of heat.
Packaging Lapox Ultrafix is available in 1.5 kg HDPE bottles.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 1.5 KG

ABOVE PRICE IS INCLUDING GST 18%
PRODUCT : FEVITITE SC 101  Description : Fevitite SC 101 is a single component heat curable , specially formulated thermosetting epoxy adhesive for bonding various engineering applications having excellent  adhesive strength to various substrates like metal, ceramic magnets etc. Since it is a single  component adhesive there is an ease of application and troublesome procedures such as  measuring, mixing, stirring are not required.  It allows faster rate of production. SALIENT FEATURES Single Component adhesive  Ease of application Bonding to Versatile substrates.  High adhesive strength.  Resistant to shock & vibrations.  Negligible shrinkage.  Excellent solvent, chemical & oil resistance. TYPICAL APPLICATION AREAS Magnet to Metal bonding in magneto assembly in motor bikes/2 wheelers.  Magnet to Metal bonding in viper motors in four wheelers.  Besides these applications Fevitite SC 101 is suitable for many more adhesive applications  in various industries & other areas where faster rate of production are required. TYPICAL PROPERTIES Sr. No. Properties Unit  Typical Data 1  Appearance  Visual observation.  Light green colored Smooth  paste  2  Viscosity at 25 DegC (Brookfield RVT Spindle No.7 /10 rpm) Poise  1400 ­ 1700  3  Tensile shear strength: SS to SS at 30 o C(After curing at 150­155 o C for 30 o C Minutes & cooled to ambient.) kg/cm2  Minimum 200 4  Solid content %  99 minimum. 5  Specific Gravity at 30 o C 1.10  ­ 1.25  6  Hardness  Shore D 80 minimum  7  Service temperature. 0 C ­15 to 150 ( Can withstand upto 200 o C intermittently for  upto 10 minutes.
Curing Instructions : Curing Schedule : 150­155 ºC  30 minutes Caution : Do not exceed curing temp 175 Deg Cel as the adhesive may start char/burn above this temperature  which may affect adhesive bond strength property. DIRECTIONS FOR USE : 1   Surface preparation – surfaces to be bonded must be free from rust, dust  Moisture, oil grease etc Mechanical roughening using emery paper , wire  brush etc is  recommended for good bond strength 2. Ensure homogeneity of the material prior to use. If required, material should  be slowly stirred to get homogeneity.  

Additional Information:

• Delivery Time: WITHIN 10 DAYS
• Packaging Details: 5 KG

ABOVE PRICE IS INCLUDING GST 18%
Ambient cure high viscous adhesive system Description Lapox Indibond is two component modified, viscous, thermosetting, multi-purpose epoxy adhesive system. When both components are mixed in recommended ratios and cured appropriately at room temperature, an excellent bond strength can be achieved with variety of materials including glass, metals, laminates, wood, textile and natural stones. Faster productivity can be achieved, if curing is performed at higher temperature between 40°C and 60°C. Applications Automobile components Textile components Electrical components General engineering components Souvenirs and handicrafts Sports goods Ceramic works Construction Advantages Adequate pot life High bond strength and mechanical strength even in dynamic conditions Thermally stable and suitable to perform in extreme conditions Water and chemical resistant Typical specifications Test Unit Reference Value Resin Hardener Description - Visual White filled viscous liquid Yellowish white filled liquid Viscosity at 25°C1 m Pas ASTM D2196 200000 - 300000 100000 - 200000 Density g/cc ASTM D792 1.30 - 1.40 1.05 - 1.15 1Viscosity by Brookfield viscometer Mix specifications Test Unit Reference Value Mixing ratio (resin : hardener) w/w - 100 : 80 Mix viscosity at 25°C m Pas ASTM D2196 100000 - 200000 Pot life1 Minutes ASTM D2471 40 - 50 Peak exotherm temperature2 °C ASTM D2471 Max 60 Surface dry* Minutes ASTM D5895 60 - 80 Touch dry* Minutes ASTM D5895 140 - 170 Hard dry* Minutes ASTM D5895 210 - 230 1Pot life of 100 g mix mass at 25 ± 1°C in plastic disposable cup by ‘Gardco’ gel timer 2Total 100 g mix mass in plastic disposable cup at 25°C *Drying time of 200 micron film on glass plate at 25°C After cure specifications 3Lap shear strength on prepared aluminum strips after 24 hours curing 4Hardness checked after 24 hours for 40 g mix mass at 25°C Processing Surface preparation:
The substrate should be dry and free from rust, oil, grease and loose particles.
Substrate must be thoroughly degreased with a good degreasing solvent (e.g. toluene, acetone trichloroethylene) and abraded with coarse emery paper, wire brush or chemically etched.
Inadequately pre-treated substrates may not bond satisfactorily. Application:
Weigh or measure out the desired amount of resin and hardener in the prescribed ratio and mix thoroughly. Mix until homogeneous and uniform color is obtained.
Apply the adhesive after mixing by spatula on the surface to be adhered. For maximum bond strength apply adhesive evenly to both surfaces.
After mixed adhesive has been applied on substrates or parts, it should be assembled immediately.
Avoid movement of assembled parts during curing.
Excess uncured adhesives can be cleaned or wiped with solvent or thinner.
The mix mass must be used within its pot life.
After use and before adhesive hardens, mixing and application equipment should be cleaned with hot soapy water or solvent. Curing:
Curing normally takes place at room temperature within about 24 hours depending on the ambient temperature but may be accelerated by the application of heat.
The joined substrate should be allowed to develop full strength before subjecting to any service loads. Packaging Lapox Indibond is available in 1.8 kg HDPE bottles . Storage and handling Lapox Indibond should be stored in a cool and dry place, preferably in a sealed container and should not be exposed to direct sunlight. This product has a shelf life of one year, if stored in its original container between 2°C and 40°C away from humidity and excessive heat.

Additional Information:

• Delivery Time: IMMEDIATE BASIS
• Packaging Details: 1.8 KG

ABOVE PRICE IS INCLUDING GST 18%
Ambient cure high viscous adhesive systemDescription Lapox Ultra is two component modified, viscous epoxy adhesive system. When both componentsare mixed in recommended ratios and cured appropriately at room temperature, an excellent bondstrength can be achieved with most of the substrates including glass, metals, laminates, wood,textile and natural stones. Faster productivity can be achieved, if curing is performed at highertemperature between 40°C and 60°C. Curing at higher temperature is recommended to achieveoptimum bond strength.ApplicationsArtificial jewellery and jewel stone fixingAutomobile componentsCeramic worksConstructionElectrical componentsGeneral engineering componentsSouvenirs and handicraftsSports goodsAdvantagesAdequate pot lifeExcellent electrical insulation propertiesHigh bond strengthHigh mechanical strength even in dynamic conditionsThermally stable and suitable to perform in extreme conditionsWater and chemical resistantTypical specifications Test Unit Reference ValueResin HardenerDescription - Visual Off-white, opaque,viscous liquidClear, yellowish tobrownish, viscous liquidViscosity at 25°C1 m Pas ASTM D2196 28,000 - 42,000 28,000 - 40,000Colour GS ASTM D1544 - Max 8Density g/cc ASTM D792 1.06 - 1.17 0.92 - 0.981Viscosity by Brookfield viscometerMix specifications Test Unit Reference ValueMixing ratio (resin : hardener) w/w - 100 : 80Mix viscosity at 25°C m Pas ASTM D2196 30,000 - 35,000Pot life1 Minutes ASTM D2471 75 - 90Peak exotherm temperature2 °C ASTM D2471 Max 60Surface dry* Minutes ASTM D5895 120 - 140Touch dry* Minutes ASTM D5895 300 - 320Hard dry* Minutes ASTM D5895 520 - 5401Pot life of 100 g mix mass at 25 ± 1°C in plastic disposable cup by ‘Gardco’ gel timer2Total 100 g mix mass in plastic disposable cup at 25°C*Drying time of 200 micron film on glass plate at 25°CAfter cure specifications1Lap shear strength on prepared aluminum strips after 24 hours curingTest Unit Reference ValueLap shear strength at 27°C kg/cm2 ASTM D1002 Min 120
ProcessingSurface reparation: The adherents must be thoroughly degreased with a good degreasing solvent(e.g. toluene, acetone trichloroethylene) and abraded with coarse emery paper or chemicallyetched. Inadequately pre-treated substrates may not bond satisfactorily.Application: The mixed mass is applied by brush or spatula on the surface to be adhered. The mixmust be used within its pot life.Curing: Curing normally takes place at room temperature within about 24 hours depending on theambient temperature but may be accelerated by the application of heat.PackagingLapox Ultra is available in 6.5 g, 13 g, 36 g, 90 g and 180 g tube packs as well as 450 g, 900 g and1.8 kg bottles and 9 kg, 45 kg and 90 kg HDPE carboys.Storage and handlingLapox Ultra should be stored in a cool and dry place, preferably in a sealed container and shouldnot be exposed to direct sunlight. This product has a shelf life of two years, if stored in its originalcontainer between 2°C and 40°C away from humidity and excessive heat.SafetyWear personal protective equipment (PPE). Avoid contact with the eyes and skin. In case of directcontact and irritation, it should be washed off immediately with soap and warm water. Avoidbreathing vapours, mist or gas. Please refer to the Safety Data Sheet (SDS) of Lapox Ultra fordetailed safety instructions.Spills and disposalIn case of spills, sweep up and shovel the spilled material. Keep spilled material in suitable, closedcontainers for disposal. Soak up with an absorbent such as clay, sand or other suitable material.Flush area with water to remove trace residue. Do not allow the product to reach the sewagesystem. Waste must be disposed of in accordance with federal, state or local regulations, asapplicable.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 6.5 g, 13 g, 36 g, 90 g and 180 g tube packs as well as 450 g, 900 g and 1.8 kg bottles and 9 kg, 45 kg and 90 kg HDPE carboys.

ABOVE PRICE INCLUDING GST  18%
Ambient cure high viscous filled adhesive system Description Lapox Fillo is two component modified, thixotropic epoxy adhesive system. When both components are mixed in recommended ratios and cured appropriately at room temperature, an excellent bond strength can be achieved with most of the substrates including glass, metals, reactive plastics, wood, textile and natural stones. Faster productivity can be achieved, if curing is performed at higher temperature between 40°C and 60°C. Curing at higher temperature is recommended to achieve optimum bond strength. Applications Joint filling system for flooring Potting system for small electronics Wood industries Advantages Good electrical insulating properties High bond strength Mechanical strength even in dynamic conditions Thermally stable and suitable to perform in extreme conditions Water and chemical resistant
Typical specifications 1Viscosity by Brookfield viscometer Test Unit Reference Value Resin Hardener Description - Visual Opaque-white, viscous liquid Brownish, viscous liquid Viscosity at 25°C1 m Pas ASTM D2196 15,000 - 25,000 15,000 - 25,000 Colour - Visual Opaque-white Opaque-brown Density g/cc ASTM D792 1.55 - 1.65 1.30 - 1.40 Mix specifications Test Unit Reference Value Mixing ratio (resin : hardener) w/w - 100 : 80 Mix viscosity at 25°C m Pas ASTM D2196 18,000 - 23,000 Pot life1 Minutes ASTM D2471 65 - 85 Peak exotherm temperature2 °C ASTM D2471 Max 65 Surface dry* Minutes ASTM D5895 70 - 90 Touch dry* Minutes ASTM D5895 170 - 190 Hard dry* Minutes ASTM D5895 270 - 290 1Pot life of 100 g mix mass at 25 ± 1°C in plastic disposable cup by ‘Gardco’ gel timer 2Total 100 g mix mass in plastic disposable cup at 25°C *Drying time of 200 micron film on glass plate at 25°C
After cure specifications 1Lap shear strength on prepared aluminum strips after 24 hours curing 2Hardness checked at 25°C on 4 mm casting. 3Water absorption checked after 24 hours curing for 20 g casting 4Application test: 36 g mix mass + 3 g Wood filler; apply 4 mm thick film on wood, sanding with number 100 emery paper Test Unit Reference Value Lap shear strength at 25°C1 kg/cm2 ASTM D1002 Min 100 Lap shear strength at 25°C (after 7 days curing) kg/cm2 ASTM D1002 120 - 140 Hardness after 4 hours2 Shore D ASTM D2240 40 - 45 Hardness after 24 hours2 Shore D ASTM D2240 65 - 70 Hardness after 7 days2 Shore D ASTM D2240 70 - 75 Water absorption at 25°C3 % ASTM D670 - 63 Max 0.4 Application test at 28°C4 (sanding time) hours - 3 - 4 Processing Surface preparation: The adherents must be thoroughly degreased with a good degreasing solvent (e.g. toluene, acetone trichloroethylene) and abraded with coarse emery paper or chemically etched. Inadequately pre-treated substrates may not bond satisfactorily. Application: The mixed mass is applied by brush or spatula on the surface to be adhered. The mix must be used within its pot life. Curing: Curing normally takes place at room temperature within about 24 hours depending on the ambient temperature but may be accelerated by the application of heat. Packaging Lapox Fillo is available in 1.8 kg bottles, 9 kg HDPE jerry cans and 45 kg HDPE carboys. Other packing may be considered on request. Storage and handling Lapox Fillo should be stored in a cool and dry place, preferably in a sealed container and should not be exposed to direct sunlight. This product has a shelf life of one year, if stored in its original container between 2°C and 40°C away from humidity and excessive heat.

Additional Information:

• Delivery Time: IMMEIDATE IF STOCK IS AVAILABLE
• Packaging Details: 1.8 KG

ABOVE PRICE IS INCLUDING GST 18%.
The product is a two-component solventfree multi purpose epoxy adhesive withfaster drying time suitable for bonding material most commonly used.The product is an effective solvent freeepoxy adhesive designed for applicationsdemanding high strength and toughness. Itis suitable for bonding a wide variety ofmaterials in common use. It can be used inart & craft, sports good manufacturing andvarious other household requirements. • Cures at Room Temperature• Excellent Adhesive strength• Bonds underprepared substrate• Good resistance to dynamic loading• Bonds a wide variety of materials incommon use• Faster dying time• Solvent Free.
Visual Appearance Clear Flowable liquid Light yellow liquid Viscosity @25°C mPa.s 16000 – 21000 25000 - 50000 Density @25°C g/cc 1.15– 1.20 0.98- 1.00 Odor Slight Yes Shelf Life 1 year when stored in original containers at room temperatures 1 year when stored in original containers at room temperaturesSurface PreparationThe mixture should be applied on a clean and oil free surface. This should be achieved by suitable mechanical and chemical means such as sandblasting Wire brushing or chemical etching. Suitable degreasing agent should be used to remove any grease, or oil traces on the surface. Application of adhesive • Use Part A & Part B in ratio 100:80 pbw. Mix the two components in small batches thoroughly for at least 2minutes. Apply the mix directly or using proper spatula to the pretreated surfaces. • The joint components should be assembled as soon as the adhesive has been applied.• Allow the material to cure for at least 24 hours before putting to use CURED PROPERTIESINSTRUCTIONS FOR USE Surface Preparation The mixture should be applied on a clean and oil free surface. This should be achieved by suitable mechanical and chemical means such as sandblasting Wire brushing or chemical etching. Suitable degreasing agent should be used to remove any grease, or oil traces on the surface. Application of adhesive • Use Part A & Part B in ratio 100:80 pbw. Mix the two components in small batches thoroughly for at least 2minutes. Apply the mix directly or using proper spatula to the pretreated surfaces. • The joint components should be assembled as soon as the adhesive has been applied. • Allow the material to cure for at least 24 hours before putting to use Mix Ratios A:B [pbw] 100:80 Pot Life @ 25˚C [min] 45-60 Cure Time [hrs] Foot Traffic @25°C 24 @35°C 16 Compressive Strength (7 days) [N/mm2 ] > 60 Tensile Strength (7 days) [N/mm2 ] > 40 Flexural Strength (7 days) [N/mm2 ]General protective equipment like gloves,proper clothing and goggles need to be used during handling to avoid any contact with skin and eyes. Regular procedures approved by local authorities to be followed for disposal.Jpoxy Polymers offers a comprehensiverange of high-performance, high-quality adhesives, flooring, jointing and repair products for both new and existing floor surfaces. Please feel free to contact for product selection, technical support service to consultants, end users and contractors and on-site support. > 30 Bond Strength (7 days) [N/mm2 ] >(Concrete failure) Water Absorption NIL Shelf Life 1 year when stored in original containers at room temperatures T

Additional Information:

• Delivery Time: READY STOCK
• Packaging Details: 1.8 KG 9 KG

ABOVE PRICE IS INCLUDING GST 18%.
PRODUCT DESCRIPTION The product is a two component high viscosity, non-porous solvent free, room temperature curing popular epoxy adhesive suitable for textile reeds, construction industry, light, heavy industry & general bonding etc. APPLICATION The product is an effective solvent free high bonding adhesive specially designed for bonding a wide variety of metals, ceramics, glass, rubber, rigid plastics and most other materials in common use. It is a excellent adhesive for use in light & heavy industry, general bonding, textile reeds and construction industry.
Cures at Room Temperature • Excellent Adhesive strength • Available in different factory pigmented colors • Good mechanical properties
Good electrical properties • Good chemical resistance • Bonds a wide variety of materials in common use • Solvent Free
TECHNICAL DATA Unit JPOXY JR 3482 JPOXY JH 2482 Visual Appearance Beige semi-liquid Grey thixotropic paste Viscosity @30°C mPa.s 10000 – 13000 65000 - 75000 Density @30°C g/cc 1.4 – 1.5 1.25- 1.35 Odor Slight Yes Shelf Life 1 year when stored in original containers at room temperatures 1 year when stored in original containers at room temperaturesINSTRUCTIONS FOR USESurface Preparation • The mixture should be applied on a clean, rough and dry surface. This should be achieved by suitable mechanical and chemical means such as sandblasting Wire brushing or chemical etching. Suitable degreasing agent should be used to remove any grease, or oil traces on the surface. Application of adhesive • Use Jpoxy JR 3482 & Jpoxy JH 2482 in ratio 100:40 pbw. Mix the two components in small batches thoroughly for at least 2minutes. Apply the mix directly or using proper spatula to the pretreated surfaces. • The joint componentsshould be assembled as soon as the adhesive has been applied. • Allow the material to cure for at least 24 hours before putting to useMix Ratios A:B [pbw]100:40 Pot Life @ 30˚C [min] 20-40 Cure Time [hrs] Foot Traffic @25o C 24 @35o C 16 Hardness (Shore D) 80 Adhesive Strength (Aluminum to Aluminum 25mm X 25mm area Lap joint) (Kg / sq. mm) > 1 Dielectric Strength (kV/mm) 30 Volume Resistivity (Ω.cm) 1017 at 50Hz Temperature Resistance upto120o C Shelf Life 1 years when stored in original containers at room temperatures PACKING HANDLING AND DISPOSAL • General protective equipment like gloves, proper clothing and goggles need to be used during handling to avoid any contact with skin and eyes. • Regular procedures approved by local authoritiesto be followed for disposal. TECHNICAL SUPPORT Jpoxy Polymers offers a comprehensive range of high performance, high quality adhesives, flooring, jointing and repair products for both new and existing floor surfaces. Please feel free to contact for product selection, technical support service to consultants, end users and contractors and on-site support. JR 3482 JH 2482 1 KG 0.4 KG 2 KG 0.8 KG 5 KG 2 KG 10 KG 4 KG 

Additional Information:

• Delivery Time: READY STOCK
• Packaging Details: 1.4 KG & 5.:2 KG

GST 18% INCLUDING ABOVE PRICE.

Aimed at a prosperous growth in this domain, we are instrumental in offering an excellent quality range of Epoxy Adhesive.

Additional Information:

• Packaging Details: 1.8 KG

ABOVE RATE IS INCLUDING OF 18% GST.
TECHNICAL DATASHEETPRODUCT : BLUEFIX- SUPER STRONGDESCRIPTION: BLUEFIX SUPER STRONG is a two component epoxy adhesive that bondsvirtually anything to anything from tiny parts to large structural components. This multipurposetwo component system comprises of Epoxy resin and Polyamide hardener which are to bemixed thoroughly in the recommended ratio to achieve optimum results. BLUEFIX SUPERSTRONG is a thermosetting system which means, the resin and hardener on mixing cure bypolymerization to a rigid thermoset mass which on heating may soften but shall not melt andflow. This system does not contain volatile matter such as solvent or water and hence there isnegligible shrinkage on curing. BLUEFIX SUPER STRONG which is internally flexiblized systemprovides strong joints with excellent low creep properties hence, make it ideal for structuralbonding applications.PRODUCT FEATURES FAST SETTING - Handling strength is achieved within 4 hours Excellent adhesion to a wide range of substrates, virtually anything to anything. Thesesubstrates include all natural wood, Plywood and engineered wood such as MDF, Particleboard which could be used in Cabinet frame making along with other substrates, Metals,Metal alloys, Ferrous/non Ferrous castings, China ware, Ceramics, Glass, Marble, Granite,Kadappa, Variety of Artificial Stones, Leather, Hardboard, Cement-Concrete, Most Plasticsviz. Rigid PVC, Filled/unfilled ABS, Polystyrene, Epoxy/Polyester FRP, Polycarbonate, Phenol-Formaldehyde (Bakelite) moulded parts, decorative /Industrial Laminates, Powder coatedmetal, Asbestos, Cork, Ferrite, etc. Please note that Plastics like PTFE, Polyethylene,Polypropylene cannot be bonded without appropriate specialized surface treatment tothese surfaces. Non-sagging nature helps in vertical applications High Cohesive Strength Good solvent/Chemical resistance Negligible shrinkage on curing and hence good dimensional stability. Good shock resistanceLong lasting bondAPPLICATION AREA:BLUEFIXSUPER STRONG is a multipurpose structural adhesive finding extensive applications invirtually all industries. These applications could be in OEM, Wood Working Joinery orMaintenance. This system is an indispensable tool for engineers and proved its value inthousands of applications in Wood Working, Automobile, Electronics, Electrical, Railway,Aeronautical, Construction and host of engineering industry.GENERAL INSTRUCTIONS FOR USE:1. Substrate Preparation : The strength and durability of bonded joint are dependent onproper pre-treatment of substrates to be bonded. At the very least surfaces to be joinedshould be cleaned with a good degreasing agent such as Acetone or Trichloroethylene inorder to remove all traces of oil, grease, rust, dust, etc. from the surface. The best and mostdurable joints are obtained by either mechanical abrading (Sand Blasting) or by chemicaletching (pickling) the degreased surfaces. Mechanical abrading shall be followed by asecond degreasing treatment.2. Mixing of RESIN and HARDENER : Epoxy resin should be thoroughly mixed withHardener .MIX RATIO PARTS BY WEIGHT PARTS BY VOLUMERESIN 100 100HARDENER 80 100Resin and Hardener are to be mixed until they form a homogeneous mix. It is very importantthat the above proportions are adhered as accurately as possible to achieve optimum results.Do not mix on high-speed mixer, which will result in sudden increase in temperature, whichshall adversely affect the pot-life of the mix. Mix, at a time, small quantity so that it can beconsumed in stipulated usable life. 50 gms of mixture of BLUEFIX SUPER STRONG has a usablelife of about 60 minutes at 30°C of room temperature.Note: Specialized Automatic Metering & Mix equipment are available in the market. Theseequipment help to improve the productivity and reliability.

Additional Information:

• Delivery Time: WITHIN TWO DAYS.
• Packaging Details: 36GM,90GM,180GM,450GM,1.8 KG

ABOVE PRICE IS INCUDING GST 18%

Description Lapox Rapid and Clear is two component modified, viscous, rapid cure and fast setting epoxyadhesive system. When both components are mixed in recommended ratios and cured appropriatelyat room temperature, an excellent bond strength can be achieved with most of the substratesincluding glass, metals, plastics, wood, textile and natural stones.ApplicationsVersatile material for most house hold and industrial applicationsAdvantagesBonding on wide variety of substratesClear film propertiesFast settingWater and chemical resistantTypical specifications1Viscosity by Brookfield viscometerTest Unit ReferenceValueResin HardenerDescription - Visual Clear, viscous liquid Clear, viscous liquidViscosity at 25°C1 m Pas ASTM D2196 60,000 - 75,000 5,000 - 13,000Colour APHA ASTM D1209 Max 70 Max 80Density g/cc ASTM D792 1.05 - 1.15 1.02 - 1.18Mix specifications Test Unit Reference ValueMixing ratio (resin : hardener) w/w - 100 : 100Mix viscosity at 25°C m Pas ASTM D2196 30,000 - 35,000Pot life1 Minutes ASTM D2471 3 - 7Peak exotherm temperature2 °C ASTM D2471 Max 60Surface dry* Minutes ASTM D5895 5 - 7Touch dry* Minutes ASTM D5895 10 - 20Hard dry* Minutes ASTM D5895 50 - 601Pot life of 10 g mix mass at 25 ± 1°C in plastic disposable cup2Total 10 g mix mass in plastic disposable cup at 25°C*Drying time of 200 micron film on glass plate at 25°CAfter cure specifications1Lap shear strength on prepared aluminum strips after 24 hours curingTest Unit Reference ValueLap shear strength at 25°C1 kg/cm2 ASTM D1002 Min 80ProcessingSurface preparation: The adherents must be thoroughly degreased with a good degreasing solvent(e.g. toluene, acetone trichloroethylene) and abraded with coarse emery paper or chemically etched.Inadequately pre-treated substrates may not bond satisfactorily.Application: The mixed mass is applied by brush or spatula on the surface to be adhered. The mixmust be used within its pot life.Curing: Curing normally takes place at room temperature within about 24 hours depending on theambient temperature but may be accelerated by the application of heat.PackagingLapox Rapid and Clear is available in 6 g, 12 g, 36 g, 90 g and 180 g tube packs. Other packing maybe considered on request.

Additional Information:

• Delivery Time: WITHIN WEEK
• Packaging Details: 6GM,12GM,36GM,90GM,180GM

ABOVE PRICE IS INDLUDING GST  18%.
Product Specification Product DescriptionAbout this item

• Comes with a fast-drying formulation which provides an instant solution to all of your flex and PVC Doors gluing requirements
• Apart from the rotational opening and easy to apply functionality this glue stick provides you a smooth applying experience without much hassle
• Flex Kwik is a transparent adhesive that does not leave any traces or marks upon drying and thereby providing a clean and nice finish
• Specially made for flex and PVC door bonding. Suitable for fixing plastic metal rubber leather ceramic.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 20 GM & 50 GM

ABOVE PRICE INCLUDING GST  18%.

This product uses in marble, wood, steel and glass with100 rupee token inside

Additional Information:

• Delivery Time: READY STOCK
• Packaging Details: I.8 KG

ABOVE PRICE IS INCLUDING GST 18%.
High strength white adhesive for bonding dissimilar substrates like marble, ceramic,metal, glass, wood, fibre glass etc.. Joints made with this system are 100% waterproof.Mixing ratio- 15:25 by weight100:100 by volumePot life- 25-30 min @ 25*c of 100 g mixHardening time- 3 to 4 hours @ 25*cCuring time- 24 hoursTensile strength- 155-165 kg/cm2Colour of Resin- whiteColour of Hardener- whiteColour of Mixture- whiteMETHOD FOR USE:The surface to be bonded should be cleaned and moisture free. The resin and hardener aremixed in the prescribed quantities on a plate with the help of a spatula. The surfacesshould be clamped together until the joint sets. .APPLICATIONS:- There of some major applications of it.1. For tile fixing,2. Tile grouting3. For making marble sink, temple4. Almirah and inlay work & Metal holdfast grouting on marble and concretesurface5. Bonding fibre glass to fibre glass.6. Bonding rigid PVC pipe to concrete.7. Dry Cement colors can be added.8. For making marble handicraft by using small marble pieces.9. Fixing of side grill on stair case.Packing - 16gm, 50gm, 200gm, 400gm, 2 kg

Additional Information:

• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 2 KG DABBA PACKING

ABOVE PRICE IS INCLUDING GST 18%

ARALDITE AW106 RESIN HV953U HARDENER MULTI-PURPOSE EPOXY ADHESIVE (AW106HV953U)

Araldite AW 106 resin/Hardener HV 953U epoxy adhesive is a multi-purpose, viscous material that is suitable for bonding a variety of materials including metal, ceramic, and wood. The electrically insulating adhesive is easy to apply either manually by spatula and stiff brush or mechanically with meter/mix and coating equipment.

Araldite AW 106 resin/Hardener HV 953U epoxy adhesive cures at temperatures from 68ºF (20ºC) to 356ºF (180ºC) with no release of volatile constituents

• Appearance of resin / hardener (mixed) : Yellow / translucent (yellow)
• Mix ratio (pbw): 100 : 80
• Mix ratio (volume) 100 : 100
• Gap Filling Capacity (mm) 0-1
• Typical lap shear strength at 23°C (sand blasted aluminium) (N/mm2): 27
• Typical lap shear strength at 23°C (sand blasted aluminium) (psi): 2560
• Flexibility / toughness” Rigid
• Chemical resistance: Good
• Water / humidity resistance: Good

APPLICATIONS:

• Metal
• Ceramics
• Wood
• Vulcanized Rubber
• Foams
• Plastic

ADVANTAGES:

• Long open time
• High shear and peel strength
• Easy to apply
• Good resistance to static and dynamic loads
• Electrically insulating

Contents:

• 1 X AW 106 RESIN 1.0KG
• 1 X HV 953 U IN HARDENER 0.8KG

Additional Information:

• Delivery Time: AVAILABLE
• Packaging Details: 13GM,36GM,90GM,180GM,270GM,450GM,900GM,1.8KG PACK

PRICE IS INCLUSIVE OF 18% GST.
PACKING : 1.1 KG.
Ambient cure high viscous adhesive systemDescription Lapox Clearset is two component modified, viscous epoxy adhesive system. When both componentsare mixed in recommended ratio and cured appropriately at room temperature, excellent bondstrength can be achieved with most of the substrates including glass, metals, plastics, wood, textile,and natural stones. Faster productivity can be achieved if curing is performed at higher temperature,i.e. 40-60°C. Curing at higher temperature is recommended to achieve optimum bond strength.Applications Zari Fixing in TextilesElectronic speakersMarble joiningArtificial jewelry & jewel stone fixingSouvenirs and handicraftsAdvantages Long pot lifeHigh bond strengthWater and chemical resistantHigh mechanical strength even in dynamic conditionsThermally stable and suitable to perform in extreme conditionsTypical specifications1Viscosity by Brookfield viscometerTest Unit Reference ValueResin HardenerDescription - Visual Clear, viscous liquid Clear, viscous liquidViscosity at 25°C1 m Pas ASTM D2196 60,000 - 75,000 30,000 - 40,000Colour APHA ASTM D1209 Max 70 Max 80Density g/cc ASTM D792 1.05 - 1.15 1.02 - 1.08Mix specifications Test Unit Reference ValueMixing ratio (resin : hardener) w/w - 100 : 100Mix viscosity at 25°C m Pas ASTM D2196 35,000 - 40,000Pot life1 Minutes ASTM D2471 60 - 75Peak exotherm temperature2 °C ASTM D2471 Max 45Surface dry* Minutes ASTM D5895 80 - 100Touch dry* Minutes ASTM D5895 240 - 260Hard dry* Minutes ASTM D5895 490 - 5101Pot life of 10 g mix mass at 25 ± 1°C in plastic disposable cup2Total 10 g mix mass in plastic disposable cup at 25°C*Drying time of 200 micron film on glass plate at 25°CAfter cure specifications1Lap shear strength on prepared aluminum strips after 24 hours curingTest Unit Reference ValueLap shear strength at 25°C1 kg/cm2 ASTM D1002 Min 120Processing Surface preparation: The adherents must be thoroughly degreased with a good degreasing solvent(e.g. toluene, acetone trichloroethylene) and abraded with coarse emery paper or chemically etched.Inadequately pre-treated substrates may not bond satisfactorily.Application: The mixed mass is applied by brush or spatula on the surface to be adhered. The mixmust be used within its pot life.Curing: Curing normally takes place at room temperature within about 24 hours depending on theambient temperature but may be accelerated by the application of heat.
Packaging Lapox Clearset is available in 0.5, 1, 2, and 10kg packs. Other packing may be considered onrequest.Storage and handling Lapox Clearset should be stored in a cool and dry place, preferably in a sealed container and shouldnot be exposed to direct sunlight. This product has a shelf life of two years, if stored in its originalcontainer between 2°C and 40°C away from humidity and excessive heat.Safety Wear personal protective equipment (PPE). Avoid contact with the eyes and skin. In case of directcontact and irritation, it should be washed off immediately with soap and warm water. Avoidbreathing vapours, mist or gas. Please refer to the Safety Data Sheet (SDS) of Lapox Clearset fordetailed safety instructions.Spills and disposal In case of spills, sweep up and shovel the spilled material. Keep spilled material in suitable, closedcontainers for disposal. Soak up with an absorbent such as clay, sand or other suitable material.Flush area with water to remove trace residue. Do not allow the product to reach the sewage system.Waste must be disposed of in accordance with federal, state or local regulations, as applicable.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 1.1 KG & BULK PACKING

ABOVE PRICE IS INCLUDING GST 18%

With our years of experience & in-depth knowledge in this field, we are engaged in offering a quality-assured array of Bulb Grede Epoxy Resin.

Details:

• Epoxy adhesive is a two-component or single-component adhesive and comprises of resin and hardened.
• On mixing the resin and hardened, fevitite solidifies by polymerisation.
• Its excellent low-creep properties and strong joints make it suitable for structural bonding applications.
• It bonds almost all engineering materials, barring few plastics.

Salient Features & Benefits:

• Good adhesion to a wide range of substrates like metal, ceramic, marble,
• granite, asbestos, glass, wood leather etc.
• High bond strength, excellent solvent and chemical resistance
• Excellent dimensional stability and negligible shrinkage
• No loss of volatile component during cure

Additional Information:

• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 1.8 KG

ABOVE PRICE IS 9KG RESIN & 3 KG HARDNER & 18% GST INCLUDING.
Ambient cure low viscous casting systemDescription Lapox Granito Cast is two component modified, epoxy based system suitable for clear castingapplication. The system is clear, having excellent optical properties with negligible shrinkage oncuring. Faster productivity can be achieved, if curing is performed at higher temperature between40°C and 60°C. Curing at higher temperature is recommended to achieve optimum performance.Applications Casting of decorative partsHandicraft itemsPaper weightsTable topAdvantages Excellent clarityGood hardness developmentGood wetting propertiesHigh gloss finishLong pot lifeLow viscosityWater and chemical resistantTypical specifications1Viscosity by Brookfield viscometerTest Unit ReferenceValueResin HardenerDescription - Visual Clear, transparent liquid Clear liquidViscosity at 25°C1 m Pas ASTM D2196 1,600 - 2,600 10 - 25Colour APHA ASTM D1209 Max 40 --Specific gravity - - 1.15 - 1.20 0.92 - 0.96Mix specifications1Pot life of 100 g mix mass at 25 ± 1°C in plastic disposable cup by ‘Gardco’ gel timer2Total 100 g mix mass in plastic disposable cup at 25°CTest Unit Reference ValueMixing ratio (resin : hardener) w/w - 100 : 33Mix viscosity at 25°C m Pas ASTM D2196 400 - 700Pot life1 Minutes ASTM D2471 450 - 600Peak exotherm temperature2 °C - Max 55After cure specifications1Hardness checked for 20 mm casting, after 24 hours curing2Tg (Glass transition temperature) development behaviorTest Unit Reference ValueHardness1 Shore D ISO/ R868 75 - 80Water absorption (24 hours immersion) % ASTM D670-63 Max 0.4Optical clarity - Visual ExcellentTg, RT curing, 24 hours2 °C DSC 45 - 55Tg, Post curing 50°C, 18 hours2 °C DSC 65 - 75Tg, Post curing 80°C, 3 hours2 °C DSC 75 - 80
Processing Mixing: Mixing is critical and must be accurate. Take resin and hardener in desired ratios. Thecombined liquids must be thoroughly mixed, manually or mechanically to completely remove anyhaziness or streaks. Scrap the sides and base of the mixing pot before transferring the mix to adesired mould for casting. It is advisable to apply the vacuum to remove air from the mix just prior topouring into the mould. It is important to mix small quantity at a time as epoxy systems tend to giveexotherm when kept in a mass.Applications: Mix mass should then be poured into a mould. The mould can be hard or made ofsilicone rubber. Moulding can be carried out by gravity or under vacuum. It does not trap air easilyand does not heat up when used properly. Excessive humidity (above ~65%), low daylight and lowtemperature (less than 20°C) may retard the curing. Lapox Granito Cast system may not workeffectively in the monsoon season. Ensure ambient material and workshop temperature is between20°C and 35°C and humidity level below 65%. Filled mould can also be kept under vacuum toachieve air free components.TroubleshootingProblem CauseUncured after 24 hours to 48 hours Wrong mix ratio and | or low ambient temperatureSticky | greasy | hazy surface High humidityAir bubbles are entrapped Mixing was too fast and did not have time to release airPackaging Lapox Granito Cast is available in 1.3 kg bottles, 4 kg jerry cans, 12 kg HDPE carboys and 260 kgMS | HDPE drums. Other packing may be considered on request.Storage and handling Lapox Granito Cast should be stored in a cool and dry place, preferably in a sealed container andshould not be exposed to direct sunlight. This product has a shelf life of one year, if stored in itsoriginal container between 2°C and 40°C away from humidity and excessive heat.Safety Wear personal protective equipment (PPE). Avoid contact with the eyes and skin. In case of directcontact and irritation, it should be washed off immediately with soap and warm water. Avoidbreathing vapours, mist or gas. Please refer to the Safety Data Sheet (SDS) of Lapox Granito Cast

Additional Information:

• Production Capacity: 12 KG
• Delivery Time: WITHIN TWO DAYS
• Packaging Details: 9KG RESIN & 3KG HARDNER & 200 KG:30KG

ABOVE PRICE IS INCLUDING GST 18%.
Product DescriptionAraldit CY 230-1
Liquid epoxy resin modified by the addition of a plasticizer.
Viscosity at 25°C ISO 2555 mPa*s 1350 2000
Specific Gravity at 25°C ISO 1675 g/cm³ 1.1 1.2
Appearance Visual Clear liquid
Epoxy content ISO 3001 Eq/kg 4.20 4.35
Flash point DIN 51758 °C 160
Aradur HY 951
Low viscosity aliphatic amine
Viscosity at 25°C ISO 12058 mPa*s 10 - 20
Specific Gravity at 20°C ISO 1675 g/cm³ 0.98
Appearance Visual Clear liquid
Flash point DIN 51758 °C 110

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 1 :1 KG & 30 KG DRUM PACK

GST 18% inclusive above price.
BONDTITE UNIWELDBondtite Uniweld is a high strength two component high technology adhesive system. This system has been designed for applications where extremely high bond strength is required. It bonds various similar and dissimilar substrates such as metals, rigid plastics (ABS, PVC, PU, Polycarbonate)., FRP, Ferrite, Ceramic, Wood, Leather, Rubber, Marble, Glass etc. This system has unique property of achieving high bond strength even if the surfaces to be bonded have traces of oil.ApplicationsAutomobiles for fixing electromagnet to flywheels, bonding brake lining to shoes, bonding metal parts to glass in miniature bulbs, for liner placement and repairing in engine.Electrical & ElectronicsFixing of magnets to metal pieces in watt hour meter, fixing aluminum caps to glass shells in night bulbs manufacturing, bonding of cooling coils to freezers in refrigerators, fixing diaphragms and magnets to base plate of speaker.AppliancesFor assembly of mixers, washing machines, gas stoves. For fixing loose handles of tools, fixing of drains, hoses, sealing of tank joints in washing machines.MiscellaneousFor fixing name plates and sign boards, joining of marbles, wash basin pieces and repairing of chipped sanitary ware, to repair broken picture frames, in repairing jewellery, to stick broken toys and brassware handicrafts & in manufacturing of sports goods like tennis racket, polo sticks etc.Restrictions on useBondtite Uniweld should not be used in under water application or on damped surface.PropertiesTwo part rubber solution with many applications.Excellent impact strength.Key Data[Resin]Physical state : Low Viscous liquidAppearance : TransparentColor : Light BlueViscosity @25°C (ASTM D 2393) : 2800-3200 [cps][Hardener]Physical State : Viscous LiquidAppearance : TransparentColor : Light RedViscosity @25°C (ASTM D 2393) : 8000- 12000 [cps][Curing properties]Mixing ratio (R:H) : 100:100 by weight(We recommended that thecomponents are weighed with anaccurate balance to prevent mixinginaccuracies which can affect theproperties of the system. Thecomponent should be mixedthoroughly to insure homogeneity)Pot life (ASTM D 2471) : 3-5 minutes at 25°C of 10 g mix(When processing large quantities ofmixture the pot life will decrease dueto exothermic reaction. It is advisableto divide large mixes into severalsmaller containers.)Hardening time : 10 min (attains 60% strength in 1hour)Strength (ASTM D 1002-10) : 100-120 kg/cm2Curing time : 2 hours at 25°CShelf Life : As long as the Resin & Hardener areunmixed and caps of the container/tubes are securely closed & kept atdry and temperature Temp 2-40°C, itcan be stored 1 years(Storage Temp 2-40°C)Hazardous decomposition : Oxides of carbon; aldehydes, acidsand other organic substances may beformed during combustion orelevated temperature (>500??? F)degradation.Disposal : Regular procedures approved bylocal authoritiesStorageProduct should be stored in a dry place in their original, properly closed containersat temperature between 2 - 40°C. Partially emptied container should be closedimmediately.Handling precautionsMandatory and recommended industrial hygiene procedures should be followedwhenever our products are being handled and processed. For additionalinformation please consult the corresponding product data sheets and thebrochure “Hygienic precautions for handling plastics products”.Packing3 gm, 7 gm, 12 gm, 36 gm, 60 gm, 90 gm, 180 gm, 270 gm, 500 gm, & 2 kg

Additional Information:

• Delivery Time: within 2 days

ABOVE PRICE IS INCLUDING GST 18%

DIAMOND (DF-R102/DFH202)DF-R102 is a modified bisphenol-A based epoxy adhesive resin to be used in conjunction withHardener DF-H202. Joints made with this adhesive system is able provide high adhesionstrength and are resistant to moisture and mild chemicals. The appropriately prepared jointsperform well even at temperature as high as 120°C.It is suitable for bonding a wide variety of metals, ceramics, glass, rubbers, rigid plastics and othermaterials, and is widely used in many industrial applications where resistance to aggressive or warmenvironments are required. The low out gassing makes this product suitable for specialist electronictelecommunication and aerospace applications.TYPICALUSE??? Submersible pump??? Repair and Maintenance??? Break Liner??? Bearing??? Marble JointsNote: Room temperature curing adhesive suitable for similar and dissimilar substratesincluding metals and FRPADVANTAGES??? Thixotropic, gap-filling??? Good chemical resistance??? Temperature resistant to 120°C??? Ambient curing??? High electrical insulation propertiesMATERIALPROPERTIESDIAMOND DF-R 102
Properties Unit Typical ValuesAppearance --- Beige PasteDensity @ 25°C g/cm3 1.64 – 1.79Viscosity @ 25°C mPas 30000 – 60000Flash Point °C 110
DIAMOND DF-H 202Properties Unit Typical ValuesAppearance --- Grey PasteDensity @ 25°C g/cm3 1.65 – 1.75Viscosity @ 25°C mPas 48000 - 100000Flash Point °C > 105PROCESSINGPROPERTIESProperty Mix RatioR:HInitial mixViscosityPot life ofMix(100gms)CuringScheduleCondition @ 25°C @ 25°CUnit W/W cPs Minutes HoursValue 100:40 60000-100000 25-30 24-29h@ RTTYPICAL PROPERTIES OF CURED SYSTEM TESTED AT 23°C(Cured 16 hours at 40°C, substrate used is aluminium)Properties Unit Test ValuesRoller Peel N/mm 1.6Hardness Shore-D - >80Tensile Strength MPa 42 -44Tensile Modulus MPa 4700PROCESSINGSTEP 1: SURFACEPREPARATIONThe adherents must be thoroughly degreased with a good degreasing solvent (e.g. toluene, acetonetrichloroethylene) and abraded with coarse emery paper or chemically etched. Inadequatelypre-treated substrates may not bond satisfactorily.Technical Data SheetPh.: 95127 84284 •Email : lubeadhesive2015@gmail.comSTEP 2: APPLICATIONThe mixed mass is applied by brush or spatula on the surface to be adhered. The mix must be usedwithin its pot-life.For best results: Roughen, dry and degrees surfaces to be bonded.STEP 3: CURINGCuring normally takes place at room temperature within about 24 hours depending on the ambienttemperature but may be accelerated by the application of heat.SAFETYFEATURES Store the container with the lid tightly closed in an upright position, in a cool, dry place Keep out of reach of children and away from eatables May be harmful if swallowed. In case of ingestion seek immediate medical attention Wear eye protection during application. In case of contact with eyes, rinseimmediately with plenty of water and if required seek medical advice

Additional Information:

• Delivery Time: DELIVERY IMMEIDATELY
• Packaging Details: 1.4 KG

ABOVE PRICE INCLUDING OF GST 18%.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 1.8 KG PACK

ABOVE PRICE IS INCLUDING GST 18%.
Product DescriptionBondtite Visco Clear from astral adhesives. For best results and genuine products, buy from jai mata Enterprise. BOND/TITE BOND TTE VISCO CLEAR VISCO CLEAR

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: WITHIN WEEK

Owing to our huge market knowledge, we have been able to offer our valued clients with a wide range of Fasto E400 Epoxy Adhesive.

Other detail:
The offered adhesive is processed with the help of excellent quality chemical compounds and advanced technology in compliance with set industrial norms.Owing to high quality, offered adhesive do not shrink over a period of time and offer optimum performance.Our entire range is made available in various specifications for our prestigious clients.Fasto E400 is a very high strength & Fast curing two-part epoxy based adhesive, in ready to use 3:1 cartridge.Fasto E400 is formulated for bonding, sealing and holding various substrates like steel, aluminum, brass, ceramic, concrete, plastics and many type of rubbers.Fasto E400 can also be used in maintenance for bonding & repairing steel, ceramic or plastic parts.
Note:
+GST 18%

Additional Information:

• Item Code: Fasto-E400

ABOVE PRICE IS INCLUDING GST 18%.

Additional Information:

• Delivery Time: WITHIN 3 DAYS
• Packaging Details: 1.8 KG & 5 :4

ABOVE PRICE IS INCLUDING GST 18% WEF DT.29.07.22


Being a customer oriented organization, we are deeply engaged in offering a wide array of Astral Pluton Adhesives.

Additional Information:

• Delivery Time: WITHIN 3 DAYS
• Packaging Details: 1.8KG & 5:4 KG

ABOVE PRICE IS INCLUDING GST 18%.

Additional Information:

• Delivery Time: WITHIN WEEK
• Packaging Details: 1.8 KG

ABOVE PRICE IS INCLUDING OF GST 18%.
Ambient cure high viscous filled adhesive systemDescription Lapox Duratite+ is two component modified, thixotropic epoxy adhesive system. When bothcomponents are mixed in recommended ratios and cured appropriately at room temperature, anexcellent bond strength can be achieved with most of the substrates including glass, metals, reactiveplastics, wood, textile and natural stones. Faster productivity can be achieved, if curing is performedat higher temperature between 40°C and 60°C. Curing at higher temperature is recommended toachieve optimum bond strength.Applications Artificial jewellery and jewel stone fixingWood furniture industriesMarble jointConcreteGlass and metalSports goodsAutomobile components and general engineering componentsHandicraftsAdvantages Long working timeHigh bond strength and mechanical strength even in dynamic conditionsThermally stable and suitable to perform in extreme conditionsWater and chemical resistantTypical specifications1Viscosity by Brookfield viscometerTest Unit ReferenceValueResin HardenerDescription - Visual Opaque viscousliquidYellowish brown, clearviscous liquidViscosity at 25°C 1 m Pas ASTM D2196 50,000 - 60,000 50,000 - 60,000Colour GS ASTM D1544 Hazy white Max 8Density g/cc ASTM D792 1.10 - 1.20 0.92 - 0.98Mix specifications1Pot life of 100 g mix mass at 25 ± 1°C in plastic disposable cup by ‘Gardco’ gel timer2Total 100 g mix mass in plastic disposable cup at 25°C*Drying time of 200 micron film on glass plate at 25°CTest Unit Reference ValueMixing ratio (resin : hardener) w/w - 100 : 80Mix viscosity at 25°C m Pas ASTM D2196 50,000 - 60,000Pot life1 Minutes ASTM D2471 75 - 95Peak exotherm temperature2 °C ASTM D2471 Max 60Surface dry* Minutes ASTM D5895 140 - 160Touch dry* Minutes ASTM D5895 340 - 360Hard dry* Minutes ASTM D5895 540 - 560LAPOX® DURATITE+Technical Data Sheet | Polymers BusinessJanuary 2018 Page 2 of 2After cure specifications Test Unit Reference ValueLap shear strength at 25°C1 kg/cm2 ASTM D1002 Min 1201Lap shear strength on prepared aluminum strips after 24 hours curing.Processing Surface preparation: The adherents must be thoroughly degreased with a good degreasing solvent(e.g. toluene, acetone trichloroethylene) and abraded with coarse emery paper or chemically etched.Inadequately pre-treated substrates may not bond satisfactorily.Application: The mixed mass is applied by brush or spatula on the surface to be adhered. The mixmust be used within its pot life.Curing: Curing normally takes place at room temperature within about 24 hours depending on theambient temperature but may be accelerated by the application of heat.Packaging Lapox Duratite+ is available in 1.8 kg bottles. Other packing may be considered on request.Storage and handling Lapox Duratite+ should be stored in a cool and dry place, preferably in a sealed container and shouldnot be exposed to direct sunlight. This product has a shelf life of two year, if stored in its originalcontainer between 2°C and 40°C away from humidity and excessive heat.

Additional Information:

• Delivery Time: WITHIN WEEK
• Packaging Details: 1.8 KG & 5:4 KG

ABOVE PRICE IS INCLDING GST 18%.

Ambient cure high viscous adhesive systemDescription Lapox Powergrip is two component modified, viscous epoxy adhesive system. When bothcomponents are mixed in recommended ratios and cured appropriately at room temperature, anexcellent bond strength can be achieved with most of the substrates including glass, metals, reactiveplastics, wood, textile and natural stones. Faster productivity can be achieved, if curing is performedat higher temperature between 40°C and 60°C. Curing at higher temperature is recommended toachieve optimum bond strength.ApplicationsArtificial jewellery and jewel stone fixingElectrical componentsGeneral engineering componentsNatural stonesSouvenirs and handicraftsSports goodsAdvantagesHigh bond strengthHigh mechanical strength even in dynamic conditionsLong pot lifeThermally stable and suitable to perform in extreme conditionsWater and chemical resistantTypical specifications1Viscosity by Brookfield viscometerTest Unit ReferenceValueResin HardenerDescription - Visual Clear, viscous liquidClear, yellowish tobrownish, viscous liquidViscosity at 25°C1 m Pas ASTM D2196 35,000 - 45,000 28,000 - 40,000Colour APHA ASTM D1209 Max 100 -Colour GS ASTM D1544 - Max 8Density g/cc ASTM D792 1.04 - 1.12 0.92 - 0.98Mix specifications Test Unit Reference ValueMixing ratio (resin : hardener) w/w - 100 : 80Mix viscosity at 25°C m Pas ASTM D2196 30,000 - 40,000Pot life1 Minutes ASTM D2471 65 - 80Peak exotherm temperature2 °C ASTM D2471 Max 60Surface dry* Minutes ASTM D5895 110 - 130Touch dry* Minutes ASTM D5895 300 - 320Hard dry* Minutes ASTM D5895 510 - 5301Pot life of 100 g mix mass at 25 ± 1°C in plastic disposable cup by ‘Gardco’ gel timer2Total 100 g mix mass in plastic disposable cup at 25°C*Drying time of 200 micron film on glass plate at 25°CAfter curespecifications1Lap shear strength on prepared aluminum strips after 24 hours curingTest Unit Reference ValueLap shear strength at 25°C1 kg/cm2 ASTM D1002 Min 95 
ProcessingSurface preparation: The adherents must be thoroughly degreased with a good degreasing solvent(e.g. toluene, acetone trichloroethylene) and abraded with coarse emery paper or chemically etched.Inadequately pre-treated substrates may not bond satisfactorily.Application: The mixed mass is applied by brush or spatula on the surface to be adhered. The mixmust be used within its pot life.Curing: Curing normally takes place at room temperature within about 24 hours depending on theambient temperature but may be accelerated by the application of heat.PackagingLapox Powergrip is available in 450 g, 900 g and 1.8 kg bottles as well as 9 kg, 45 kg and 90 kgHDPE carboys.Storage and handlingLapox Powergrip should be stored in a cool and dry place, preferably in a sealed container andshould not be exposed to direct sunlight. This product has a shelf life of two years, if stored in itsoriginal container between 2°C and 40°C away from humidity and excessive heat.SafetyWear personal protective equipment (PPE). Avoid contact with the eyes and skin. In case of directcontact and irritation, it should be washed off immediately with soap and warm water. Avoidbreathing vapours, mist or gas. Please refer to the Safety Data Sheet (SDS) of Lapox Powergrip fordetailed safety instructions.

Additional Information:

• Production Capacity: AVAILABLE
• Delivery Time: IMMEDIATE
• Packaging Details: 450GM,900GM,1.8KG,9KG

ABOVE PRICE IS INCLUDING OF 18% GST.PACK SIZE IS 1.25 KG
Ambient cure low viscous systemDescription Lapox Granito JR-150 | JH-350 is two component modified, epoxy based system suitable fortreatment of Italian marbles and granites. It is a room temperature curing system, having low viscousand good penetrating properties into cracks for marbles and granites. The system shows excellentimpregnation and gloss properties after curing. Faster productivity can be achieved, if curing isperformed at higher temperature between 40°C and 60°C. Curing at higher temperature isrecommended to achieve optimum performance.ApplicationsFilling and coating of Italian marbles and granitesAdvantagesEnhance self-colour of the granites and Italian marblesGood colour stabilityGood penetrating power into cracksHigh glossLow shrinkageSystem can be pigmentedThermally stable and suitable to perform in extreme conditionsWater and chemical resistantTypical specifications1Viscosity by Brookfield viscometerTest Unit Reference ValuesResin HardenerDescription - Visual Clear, transparentliquidClear, transparentliquidViscosity at 25°C1 m Pas ASTM D2196 450 - 650 10 - 20Colour APHA ASTM D1209 Max 60 -Colour GS ASTM D1544 - Max 1Specific gravity - - 1.10 - 1.20 0.95 - 1.00Mix specifications Test Unit Reference ValueMixing ratio (resin : hardener) w/w - 100 : 25Mix viscosity at 25°C m Pas ASTM D2196 200 - 300Pot life1 Minutes ASTM D2471 35 - 45Peak exotherm temperature2 °C - Max 135Surface dry3 Minutes ASTM D5895 100 - 120Touch dry3 Minutes ASTM D5895 170 - 1901Pot life of 100 g mix mass at 25 ± 1°C in plastic disposable cup by ‘Gardco’ gel timer2Total 100 g mix mass in plastic disposable cup at 25°C*Drying time of 200 micron film on glass plate at 42 ± 0.5°CAfter cure specifications1Hardness checked for 10 mm casting, after 24 hours curing2Tg (Glass transition temperature) development behavior ProcessingSurface preparation: Clean thoroughly the crack area on marbles. Ensure the surface is free fromdirt, oil, grease and moisture. Wipe off the surface of the marble with clean cloth. Inadequately pretreatedsubstrates may not show satisfactory results.ApplicationCrack filling: Take resin and hardener as per mentioned ratio, mix thoroughly. Take it in dispensingbottle, dispense mix over the cracks. Pigmentation can be done by adding suitable pigment.Micro | hair line crack treatment: Take resin and hardener in above mentioned ratio, mixthoroughly and apply the mix over complete surface of marble with the help of a metal spatula. Applyas many coats as required, depending upon the nature of cracks on the surface. Allow to cure in daylight for 24 hours. The excess material can be grinded and removed from the surface of thesubstrate. Excessive humidity (above ~65%), low daylight and low temperature (less than 20°C) mayretard the cure. The Lapox Granito JR-150 | JH-350 system will not work effectively in the monsoonseason.Polishing of marbles and granites: It can be done after 24 hours to 30 hours from the time ofLapox Granito JR-150 | JH-350 application on surface.TroubleshootingProblem CauseUncured after 24 hours to 48 hours Wrong mix ratio and | or low ambient temperatureSticky | greasy | hazy surface High humidityPackagingLapox Granito JR-150 | JH-350 is available in 1.25 kg bottles, 5 kg and 10 kg HDPE jerry cans and250 kg MS | HDPE drums. Other packing may be considered on request.Storage and handlingLapox Granito JR-150 | JH-350 should be stored in a cool and dry place, preferably in a sealedcontainer and should not be exposed to direct sunlight. This product has a shelf life of one year, ifstored in its original container between 2°C and 40°C away from humidity and excessive heat.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 1.25 KG,5KG,10KG