Lube Adhesive & Engineering Co.
Ahmedabad, Gujarat
GST No. 24AQYPM1863D1ZL
Call 08048964000 75% Response Rate
Rubber Adhesive
We are a leading Wholesale Supplier of fevicoll sr cbr 7 synthetic rubber adhesive, anabond 230 brake & clutch liner bonding adhesive, fevicol 1 k pur, sr 998 fwr, maax easybond sprayble adhesive and sr 505 rubber base adhesive from Ahmedabad, India.
Fevicoll SR CBR 7 Synthetic Rubber Adhesive
Rs 645 / PackGet Best Price
Minimum Order Quantity: 10 Pack
Product Brochure
| Model Number | FEVICOL SR CBR 7 & CBA 7 |
| Packaging Size | 1LTR +100GM |
| Packaging Type | Tin Can |
| Product | CBR 7-CBA 7 |
| Color | Reddish Yellow Liquid |
| Solid Content | CBR 7-18-19% |
| Viscosity | 12-16 |
| Minimum Peel Strength | 14.0 Kg/inch |
| Drying time | 5 min |
| Temperature Resistance | -20 to +80 |
| Applications | Suitable for conveyor belts, rubber linings and heavy duty rubber sheets/mats joining, etc. |
ABOVE PRICE IS INCLUDING OF GST 18 % .& RESIN HARDNER BOTH PRICE INCLUDING.
PRODUCT : FEVICOL SR CBR 7
Description : Fevicol SR CBR 7 is a two component synthetic rubber based adhesive cement which cures at room temperature. The adhesive cement system is ideally suitable for joining and emergency maintenance of conveyor belts It can be also used for other application such as rubber linings.
Salient Features : Faster curing. Reduces down time. Ease of application. Adequate tack retention time. Longer Shelf Life.
Typical Properties ( Resin & Activator Mix ) : Mixing Ratio : (100 : 5 parts by weight)
Sr.No Properties Unit Typical Data
1 Color & Appearance --- Yellowish Brown viscous liquid
2 Solids % 18 - 19 3 Viscosity @ 30 0 C Poise 12-16
4 Tack retention time at ambient Min 5 -7
5 Open Time Min Minimum 5 Min Application Area : Fevicol CBR 7 is used to bond rubber to rubber sheat by lap shear (overlap ) joints. This product is extensively used in maintanance of Conveyor Belts in steel plants & similar industries.
Method of Application :
Surface preparation : The surface to be repaired must be free from moisture, oil, dust, grease etc. The surface should be roughened by using buffing tools to achieve the desired performance.
Mixing Method : In a clean metallic container mix the resin and activator in the specified ratio (100:5 parts by weight) and stir the mixture using a clean metallic/wooden rod thoroughly to get a homogeneous mass.
Application : Apply the mixture by brush, on both the prepared surfaces and wait for 5 to 7 minutes depending at ambient . Then apply the second coat in a similar manner. After five minutes bond the two surfaces in such a manner that no air bubble is trapped . This is achieved by application of suitable roller.
Note : Tightly close the containers immediately after use.
Curing Schedule : The repaired component will have adequate handling strength in approximately two hours at ambient. Full strength will be achieved after a curing of 24 hours at ambient condition.
Safety Precautions Avoid contact with skin, eyes etc use of hand gloves and safety goggles is recommended Application area should have good ventilation. Detailed MSDS will be available on request.
Shelf Life : Fevicol SR CBR 7 (Resin & Activator) has a shelf life of 12 months from the date of manufacture when stored in original sealed container .when stored in covered storage area away from direct sunlight, rains, moisture etc.
Packing : Resin : 1 lit & 5.5 lit and Activator : 50 ml & 500 ml
Additional Information:
- Delivery Time: WITHIN 7 DAYS
- Packaging Details: 1 LTR RESIN & 100 GM HARDNER
View Complete details
get quote
request a call back
Anabond 230 Brake & Clutch Liner Bonding Adhesive
Rs 1,120 / KgGet Best Price
Minimum Order Quantity: 12 Kg
Product Brochure
| Brand | Anabond |
| Model Number | Anabond |
| Packaging Size | 20 Kg |
| Packaging Type | Tin |
| Application Industry | Automotive |
| Surface Of Application | metal to shoe |
| Grade Standard | Industrial |
| Strength | High |
| Material Compatibility | Metal |
Additional Information:
- Delivery Time: within 3 days
- Packaging Details: Tin packing MOQ 12
View Complete details
get quote
request a call back
Fevicol 1 K Pur
Rs 330 / NumberGet Best Price
Minimum Order Quantity: 12 Number
Product Brochure
| Surface Of Application | wood application |
| Material | polyurethane adhesive |
| Features | good Adhesion |
| Temperature Range | between 15 to 45 degree C |
| Product Code | 1k pur |
| Viscosity | 40 to 80 ps |
| Adhesion Strength | 24 hours |
| Dry Time | 10 to 15 minutes |
| Adjustability Time | 2 - 3 hours |
| Color | clear light brown |
| Brand | Pidilite |
| Adjustment Time | between 15 to 45 degree C |
| Coverage | 100 - 200 g/sq. m |
| Density | 40 to 80 ps |
| Item Code | 1 k Pur |
| Dry Solid Content | 42 |
| Packaging Type | 500 Ml |
| Dry Solids Content | 42 |
| Dynamic Movement Capacity | Flaxible |
| Open Time | 10 to 15 minutes |
| Peel Strength | 2 to 3 hours |
| Ready For Use | immediate |
| Shore A Hardness | High |
| Skin Time | 2 to 3 hours |
| Storage | bellow 25 C |
| Tensile Adhesion Strength | 24 hours |
| Tensile Strength | 24 hours |
| Packaging Size | 500 ml |
| Grade Standard | Industrial Grade |
| Usage/Application | wood to wood |
| Form | Liquid |
ABOVE PRICE IS 18% GST EXLUSIVE.
Fevicol PUR (1K) Moisture curing single – component Polyurethane adhesive.Fevicol 1K PUR has excellent boiling water resistance and confirms to EN 204/D4and JAS (BWSD) standards. It also confirms to high heat resistance as per WATT91.PROPERTIES OF THE ADHESIVE??? Appearance : Clear light brown liquid.??? Viscosity @ 30 deg. C : 40 – 80 Ps.??? Open time : 10 to 15 minutes @ 30 deg. C. Higher temperature andhigher percentage of moisture would reduce the opentime.??? Handling time : 2 – 3 hours.??? Final Bond strength : 24 hours.??? Coating weight : 100 – 200 g/sq. m??? Application temperature : between 15 to 45 degree C.FIELDS OF APPLICATION??? Edge to Edge Joints,??? Finger Joint Applications??? Different Joint applications like Tenon and Morist Joints, Tongue and Grove Joints.??? Typical applications are in making frames of window, door, and wooden staircaseswhere it gives an exceptionally high mechanical strength.??? Bonding of MDF board Joints??? OTHER AREAS OF APPLICATION: Meant for bonding wood, MDF, fiberboard,particleboard, metal, laminates, stone, ceramic, brick, foam, fiberglass, marble,leather, cork, drywall, mirrors, fabric, plaster, plasterboard, masonry, rubber, someplastics and many other substrates.Application Technique:-(a) Applicator: - With spatula or hand roller from plastic squeeze bottle(b) Application Process :-??? Surface to be bonded should be dry, clean, and free from oil and grease.??? Open the bottle lid by turning the yellow top anti-clockwise.??? Apply glue on one of the edges of the wood substrate / panel /plank / joint etc. in athin layer by pressing the bottle downwards. Spread the glue uniformly on the edgewith the help of spreader.??? Close the bottle lid after application by turning the top clockwise.??? Dampen the edge of the second wood substrate / panel /plank / joint etc to bebonded by spraying water.??? Bring the edges of both the substrates close to each other to assemble & clamp themfirmly.??? Leave the assembly to set. It will set in 30minutes. De-clamp the substrates after 2Hrs.??? During curing, the product creates foam & expands, which helps in filling gaps.??? A strong bond is achieved after 2 - 3 hours.??? Optimum strength will be realized after 24 hours at room temperature.
Additional Information:
- Production Capacity: Stock Available
- Delivery Time: Within 2 days
- Packaging Details: 500 gm
View Complete details
get quote
request a call back
SR 998 FWR
Rs 160 / LTRGet Best Price
Minimum Order Quantity: 100 LTR
Product Brochure
| Usage/Application | Industries |
| Brand | Fevicol |
| Surface Of Application | Industries |
| Grade Standard | Industrial Grade |
| Adhesive Type | Synthetic |
| Origin | Synthetic |
| Form | solvent |
| Color | Dark Brown |
APPLICATION INSTRUCTIONS :· Proper surface preparation is important to get optimum & consistent results. Surfaces mustbe dry and free from dust, dirt, oil & grease, mould release agent and other contaminants.SUBSTRATE PREPARATIONMicro/Neolite Rubber Roughen & solvent wipeUpper/Sole Leather RoughenEVA RoughenResin Rubber Roughen & Solvent wipe ( Toluene)· Apply the adhesive uniformly on both the substrates to be bonded bybrush or appropriate applicator. Porous substrates may require a second coat, which canbe applied after 510minutes of first coat.· Allow to dry for 1520minutes at room temperature. The adhesive afterdrying exhibits tack. The finger test has proven itself to be a reliablemethod of judging the OPENTIME.Whereas this time only serves as arough indication , variance may occur due to temperature, relativehumidity, type of substrates etc. In the finger test the adhesive must feeldry but tacky. The substrates bonded after prolonged opentime& in theabsence of tack may result in inferior coalescence & bond strength..· After appropriate OPENTIME(which is the span between Dryingtime& Tack RetentionTime) bring both the substrates together align them properly and press firmly. The bondedcomponents need not be kept under pressure fixture.· Even though the instant contact bond strength is sufficient to take care of spring backaction between sole & upper, the bond strength builds up further in 24hrs to 48hrs.Special features :· Free from BenzeneNonhazardousto health.· Unparallel bonding strength.· Excellent Green strength.· Preferred by the users dealing only in quality works.STORAGE & SAFETY PRECAUTIONS :Keep the adhesive container closed when not in use. The adhesive is highly flammable hencesmoking and nakedflamemust be avoided in the working area. Store the adhesive in a cool(<25 0 C ) & dry area , away from direct sunlight & heat. Proper ventilation must be provided onthe shopfloor.Refer MSDS for details.SHELF LIFE : Minimum 1 year from the date of manufacture in sealed condition when storedunder recommended storage conditions.Packing : 1 Lit.,5 Lit., 25 Lit.
Additional Information:
- Delivery Time: within 2 days
View Complete details
get quote
request a call back
Maax Easybond Sprayble Adhesive
Rs 400 / NumberGet Best Price
Minimum Order Quantity: 24 Number
Product Brochure
| Brand | MAAX LUBRICATION |
| Model Number | MAAX EASYBOND |
| Packaging Size | 500 ML |
| Packaging Type | BOTTLE |
| Application Industry | Packaging, Automotive |
| Surface Of Application | Metal, Ceramic, Plastic |
| Form | LIQUID SPRAY |
| Grade Standard | Industrial |
| Strength | High |
| Country of Origin | Made in India |
MAAX EASY BOND 203 | 204 Heavy Duty Spray Adhesive Features Higher Strength and fast Grabbing Multipurpose adhesive Sufficient open time for proper surface positioning Heat and moisture resistant Fast tack and Pressure sensitive Higher coverage area Economical & Easy to use Applications Designed as a Multipurpose adhesive spray used for numerous permanent bonding applications to bond wood, Laminates, veneer ,charcoal sheet ,highlighters, , card board, soft foams, cloth, fibre glass insulation, plastic, polyethylene, polypropylene, craft making, metal, furniture, thin films, foils, etc. Method of Use Shake well Before Use, till the movement of the ball is audible Remove cap, hold can 4-5 inches from the surface to be applied and spray a thin layer. Specifications Property MAAX– EASY BOND 203 |204 Colour White Translucent Specific Gravity (g/cc) 0.80± 0.02 Base Synthetic Elastomer Spray Pattern Type Mist Drying Time 1-2 Minutes Bonding time 30 Min Initial Bonding, 24 Hours complete bonding Area of Coverage 60-70 sq.ft Propellant Type CFC Free
Additional Information:
- Delivery Time: WITHIN WEEK
- Packaging Details: 500 ML
View Complete details
get quote
request a call back
SR 505 Rubber Base Adhesive
Rs 230 / LitreGet Best Price
Minimum Order Quantity: 30 Litre
Product Brochure
| Packaging Type | Tin Can |
| Brand | SR Adhesive |
| Surface of Application | Wood |
| Application Industry | Laminating, Footwear, Flooring |
| Form | rubber base adhesive |
| Color | yellow |
| Material Compatibility | Metal |
| Chemical Resistance | ANOTHER |
| Shelf Life | 1 year |
| Packaging Size | 30 ltr |
| Material | fevicol |
| Grade Standard | Industrial Grade |
DESCRIPTION: FEVICOL SR 505 is a synthetic rubber based solvent containing
contact adhesive for Multipurpose applications. It exhibits immediate bond
strength and has good resistance to water and aging. This adhesive can be
applied by brush, applicator/finger.
APPLICATION AREA: FEVICOL SR 505 is used to bond PVC to Mosaic
/concrete substrate in Flooring segment. Used to bond variety of substrates like
U-Foam/Rubber Foam to U-Foam, Rexine to Foam, Wood/Plywood to U-Foam,
Coir to U-Foam etc. in Upholstery segment. Also used in various handicraft
applications & for Bus body tops & seat cover pasting & in Veneer Industry.
TYPICAL PHYSICAL PROPERTIES:
APPEARANCE : Light yellowish liquid
VISCOSITY @ 300C : 12-16 Poise
by brookfield viscometer
rvt/spindle #3/20 rpm
SP.Gravity : 0.820 – 0.860 gm/ml
Flash point : 00c to 40c
Drying time
(on G.P by 2 thaw applicator at 30+ 2oc) : 15-35 secs approx.(varies as
per climatic conditions)
Packaging : 25lits. Drum, 5lits, 1lits &
500ml tin
1
APPLICATION INSTRUCTIONS :
· Surface to be bonded should be clean, dry and free from oil/grease stains.
· Stir the adhesive before application.
· Apply FEVICOL SR 505 on both the surfaces. Non-porous surfaces to be
applied first & then the porous surfaces.
· Once the adhesive becomes dry, press both the surfaces together, ensuring
uniform contact.
· Final bond is achieved in 24hrs.
Special features :
· Free from Benzene- Non-hazardous to health..
· Multiple usages.
· Excellent spreadability.
· High coverage specially on flooring – 90 sq ft per litre depending upon the
floor conditions.
· Mild smell.
· Economical in long run.
S AFETY PRECAUTIONS :
Keep the adhesive container closed when not in use. The adhesive is highly
flammable hence smoking and naked-flame must be avoided in the working
area. Store the adhesive in a cool (<250C ) area . Proper ventilation must be
provided on the shop-floor.
SHELF LIFE :
At least one year from the date of manufacture in sealed condition if stored under
recommended storage conditions.
DILUENT / CLEANER :
Toluene may be used to clean the tools used for the application.
N OTE : A detailed MSDS is available on request.
Additional Information:
- Delivery Time: WITHIN 2 DAYS
View Complete details
get quote
request a call back
Polygrip Rapid
Rs 184 / LitreGet Best Price
Minimum Order Quantity: 30 Litre
Product Brochure
| Brand | ATUL LTD |
| Model Number | POLYGRIP RAPID |
| Packaging Size | 30 LTR |
| Packaging Type | DRUM |
| Application Industry | SOFA MFG, Footwear |
| Surface Of Application | Fabric, Rubber |
| Form | LIQUID |
| Grade Standard | Pharmaceutical |
| Strength | Medium |
| Country of Origin | Made in India |
DescriptionPolygrip Rapid is yellow to brownish red colored very fast drying sprayable synthetic styrene-butadiene-styrene rubber based adhesive. It is recommended for bonding variety of substrates like foam, painted metal, MS, FRP, ABS, polypropylene, PVC foam, wood, rexin, fabric and non woven carpet.Advantages Low smell Fast drying Low wastage Higher coverage High productivity No harmful benzene Rapid strength development Low absorption on foam surfaceApplications Luggage Generator canopy Upholstery fixing and seat making Sofa, mattress & chairs manufacturing Automobile (roof lining, door trim, non woven carpets)
Typical specifications Properties Unit Test method Values Appearance -- Visual Yellow to brownish red low viscous liquid Density at 30ºC g/ml -- 0.80 - 0.85 Viscosity at 30ºC cPs ASTM D 2196 100 - 150 *Tack retention time Minutes -- Max. 10* Tack retention time (open time) is generally measured after evaporation of solvent once adhesive applied in thin film. It may vary depending upon ambient temperature & humidity conditions.
Process of application(1) Surface preparation Ensure that substrates to be bonded are clean, dry and free from oil, grease and foreign particles such as dust and rust(2) Application Method Stir adhesive well and make it homogeneous prior to use Spray the adhesive by using air supported gun (make-Pilot) having orifice diameter of 1.5-2.0 mm at air pressure of 45-55 psi Allow evaporation of solvents for 1-2 minutes Assemble both the substrates with uniform contact pressure to achieve intimate contact without air pockets The optimum bond strength is achieved after 24 hrs.PackagingPolygrip Rapid is available in 4.5 and 30 liters MS drums. Other packing may be considered on request.Storage and handlingPolygrip Rapid should be stored in cool & dry place away from moisture, heat & direct sunlight. It contains highly volatile solvents, which will release during application,processing and use. These volatile solvents are highly flammable, hence adhesive must not come in contact with heat, spark and necked flame. This product has a shelf life of 1 year if stored in its original container between 2°C and 40°C away from humidity and excessive heat.SafetyWear personal protective equipment (PPE). Avoid contact with the eyes and skin. In case of direct contact and irritation, it should be washed off immediately with soap and warm water. Proper ventilation must be provided to shop floor where adhesive is used. Avoid breathing vapours, mist or gas. Please refer to the Safety Data Sheet (SDS) of Polygrip Rapid for detailed safety instructions.Spills and disposalIn case of spills, sweep up and shovel the spilled material. Keep spilled material in suitable, closed containers for disposal. Soak up with an absorbent such as clay, sand or other suitable material. Flush area with water to remove trace residue. Do not allow the product to reach the sewage system. Waste must be disposed of in accordance with federal, state or local regulations, as applicable.
Additional Information:
- Production Capacity: AVILABLE
- Delivery Time: IMMEDIATE
- Packaging Details: 30 LTR & 4.5 LTR
View Complete details
get quote
request a call back
Polygrip Sp 809
Rs 1,056 / LitreGet Best Price
Minimum Order Quantity: 4 Litre
Product Brochure
| Brand | Atul Ltd |
| Model Number | POLYGRIP SP 809 |
| Packaging Size | 5 LTR |
| Packaging Type | Tin Can |
| Application Industry | Flooring, Laminating |
| Surface Of Application | PVC, Rubber, Fabric |
| Grade Standard | Industrial |
| Strength | High |
Description Polygrip SP-809 is a yellow coloured synthetic rubber based contact adhesive. It is amultipurpose adhesive suitable for bonding variety of substrates such as rubber, leather,EVA, rexin, wood, laminate, FRP, painted MS, foam and canvas.Advantages Ease of application with good coverageExcellent tack qualityHigh bond strengthLong lasting durable bond with excellent water resistanceMild smellNo harmful benzeneApplications Automotive interiorsFootwearFurniture manufacturingHandicraftHVAC applications - AC ducting, chilled water piping and under deck insulationPVC flooring | carpet lyingUpholstery and mattressTypical specifications Properties Unit Test method ValuesAppearance - VisualLight-yellow, medium viscousliquidDensity at 30°C g/ml - 0.82 - 0.86Viscosity at 30°C c Ps ASTM D2196 1,050 - 1,500Tack retention time1 Minutes - Max 301Tack retention time (open time) is generally measured after evaporation of solvent once adhesive applied in thin film.It may vary depending upon ambient temperature and humid conditions.Process of application Surface preparation:Ensure that substrates to be bonded are clean, dry and free from oil, grease and foreignparticles such as dust and rust.Application method: Stir adhesive well and make it homogeneous prior to use. Applyadhesive uniformly in thin layer on both the substrates to be bonded with brush, spatula orany suitable tool. Allow evaporation of solvent from adhesive layer. The evaporation ofsolvent may take 5 minutes to 10 minutes, which depends upon ambient temperature andhumidity. Assemble both the substrates with uniform contact pressure to achieve intimatecontact without air pockets. The optimum bond strength is achieved after 24 hours.Packaging Polygrip SP-809 is available in 1 L, 2 L, 5 L and 30 L MS drums. Other packing may beconsidered on request.Storage and handlingPolygrip SP-809 should be stored in cool and dry place away from moisture, heat and directsunlight. It contains highly volatile solvents, which will release during application, processingand use. These volatile solvents are highly flammable, hence adhesive must not come incontact with heat, spark and necked flame. This product has a shelf-life of 1 year if stored inits original container between 2°C and 40°C away from humidity and excessive heat. Pleaserefer to the Safety Data Sheet (SDS) for detailed instructions on storage and handling.
Additional Information:
- Delivery Time: IMMEDIATE
- Packaging Details: 5,LTR & 30 LTR
View Complete details
get quote
request a call back
Superbond Yellow 7 Spray / Brush Rubber Adhesive
Rs 147 / LitreGet Best Price
Minimum Order Quantity: 30 Litre
Product Brochure
| Packaging Size | 30 LTR DRUM PACK |
| Usage/Application | Plastic |
| Grade Standard | Industrial Grade |
| Form | Liquids |
| Origin | Synthetic |
| Features | SOLVENT FREE |
| Color | YELLOWWISH BROWN LIQUID |
| Material | RUBBER BASE ADHESIVE |
| Brand | SUPERBOND ADHESIVE |
Product Description: ???Yellow 7 is multipurpose adhesive is specially developed for Mattress Industries where extragreen strength is required & other use is in Furniture Sector, Non Oven, PU Foam, HitlonFoam, & general purpose bonding.Method of use:???1) Air pressure pilot spray gun used for spraying purpose. Air compressor should be free fromtraces of water.2) Air Pressure:???3.5 to 5 Kg/cm2.3) Nozzle Orifice Size:???1.6 to 2 mm.4) Ideal distance 2 to 3 feet from the substrate.Properties;???1) Appearance : ???Yellowish Brown Liquid.2) Viscosity : ??? 50 To 80 cPs@300C + 20C4) Coverage : ??? 80 to 100 gms. / meter25) Shelf Life : ??? One year from date of manufacturing in the sealed container.6) Tack Time : ???18 to 30 minutes.7) Density : ??? 0.78 + 0.05 gm/ml@300C + 20C.8) Odour : ??? Not Offensive.
Additional Information:
- Production Capacity: IMMEDIATE
- Delivery Time: WITHIN 3 DAYS
- Packaging Details: 30 LTR DRUM PACK
View Complete details
get quote
request a call back
Polygrip Synthetic Rubber Adhesive
Rs 23.6 / NumberGet Best Price
Minimum Order Quantity: 50 Number
Product Brochure
| Brand | ATUL LTD |
| Model Number | POLYGRIP SYNTHETIC RUBBER ADHESICE |
| Packaging Size | 40 ML |
| Packaging Type | TUBE |
| Application Industry | Footwear |
| Surface Of Application | JUTE, Rubber, PVC, Fabric |
| Grade Standard | Industrial |
| Strength | High |
| Country of Origin | Made in India |
DescriptionLapox Polygrip is special grade with extra light in colour synthetic rubber base adhesive. High bond strength can be achieved if used at appropriate environmental and processing conditions.Advantages??? Mild smell??? High bond strength??? No harmful benzeneApplications??? Addition of jerry on Saris??? Upholstery fixing, seat making, etc??? Securing PVC / Jute / Rubber carpets to floor??? Adhesion of insulation material lining in Air Conditioning??? Bonding of Foam to Rexin, Metal and Plastics in Furniture??? Adhesion of interior fabric lining attachment in luggage manufacturing??? Permanent bonding of leather to leather, leather to soles made of MCR, EVA, rubber; corkTypical specificationsProperties Unit Test method Values Appearance -- Visual Yellow Density at 30ºC g/ml -- 0.82 - 0.87 Viscosity at 30ºC cPs ASTM D 2196 1800 - 2300 *Tack retention time me Minutes -- Max. 30* Tack retention time (open time) is generally measured after evaporation of solvent once adhesive applied in thin film. It may vary depending upon ambient temperature & humidity conditions.Process of application(1) Surface preparation??? Ensure that substrates to be bonded are clean, dry and free from oil, grease and foreign particles such as dust and rust(2) Application Method??? Apply adhesive on both side the substrates by brush or appropriate machine.??? Allow evaporation of solvent from adhesive layer. The evaporation of solvent may take 5-10 minutes, which depends upon ambient temperature and humidity??? Assemble both the substrates with uniform contact pressure to achieve intimate contact without air pockets??? The optimum bond strength is achieved after 24 hrsPackagingLapox Polygrip is available in 20 and 40 milliliters tube. Other packing may be considered on request.Storage and handlingLapox Polygrip should be stored in cool & dry place away from moisture, heat & direct sunlight. It contains highly volatile solvents, which will release during application, processing and use. These volatile solvents are highly flammable, hence adhesive must not come in contact with heat, spark and necked flame. This product has a shelf life of 1 year if stored in its original container between 2°C and 40°C away from humidity and excessive heat.
SafetyWear personal protective equipment (PPE). Avoid contact with the eyes and skin. In case of direct contact and irritation, it should be washed off immediately with soap and warm water. Proper ventilation must be provided to shop floor where adhesive is used. Avoid breathing vapours, mist or gas. Please refer to the Safety Data Sheet (SDS) of Polygrip Lapox Polygrip for detailed safety instructions.Spills and disposalIn case of spills, sweep up and shovel the spilled material. Keep spilled material in suitable, closed containers for disposal. Soak up with an absorbent such as clay, sand or other suitable material. Flush area with water to remove trace residue. Do not allow the product to reach the sewage system. Waste must be disposed of in accordance with federal, state or local regulations, as applicable.
Additional Information:
- Production Capacity: AVAILABLE
- Delivery Time: IMMEIDATE
- Packaging Details: 40ML & 20ML PACK
View Complete details
get quote
request a call back
Superbond Yellow 4
Rs 175 / LTRGet Best Price
Minimum Order Quantity: 15 LTR
Product Brochure
| Usage/Application | SOFA,CHAIR,AUTOMOTIVE |
| Form | Liquids |
| Curing Method | Moisture Activated Curing |
| Material | SOLVENT BASE ADHESIVE |
| Brand | SUPERBOND |
| Packaging Size | 15 LTR |
| Grade Standard | Industrial Grade |
| Surface Of Application | Wood |
| Material Compatibility | Paper |
| Packaging Type | Drum |
Superbond yellow 4technical literaturecolour : yellowviscosity : 100 cps + 30 cps at 25ºcodour : non-offensivebond strength : 26. 6 kg (steeel sheet to vinyl sheet)open tack time : 20-30 min. Green tack time : 4-5 sec. Coverage : 100 to 105 sq. Ft/ ltrcuring time : 24 hoursapplication : by spray or by brushshelf life : six months
Additional Information:
- Delivery Time: within 2 days
View Complete details
get quote
request a call back
ANABOND ALL PURPOSE RUBBER ADHESIVE
Rs 55 / UnitGet Best Price
Minimum Order Quantity: 50 Unit
Product Brochure
| Brand | ANABOND |
| Model Number | ANABOND ALL PURPOSE ADHESIVE |
| Packaging Size | 100 ML |
| Packaging Type | TUBE |
| Application Industry | INDUSTRIAL APPLICATION |
| Surface Of Application | Rubber |
| Grade Standard | Industrial |
| Strength | High |
| Country of Origin | Made in India |
Anabond all purpose adhesive is a clear adhesive, single component synthetic polyester PU based adhesive suitable of bonding of various substrates such as LeatherLeather, Leather Canvas, Aluminium aluminium, Paper Paper, Neoprene Neoprene, Wood Wood, WoodCanvas, broken pottery items etc. The adhesive system attains strength after solvent evaporation followed by crystallization. The bonded joint is highly resistant towards humid conditions. METHOD OF USE Remove completely oil, oxides, dirt's etc., from the substrates such as leather, canvas, aluminum, paper, Neoprene, etc., to be bonded. Apply the adhesive uniformly with a brush and allow the solvent to evaporate for 1 to 2 minutes. Assemble the joints within 23 minutes, ensuring contact pressure uniformly and allow it to crystallizing at ambient temperature for a minimum period of 5 hrs. to achieve handling strength. AL/0201/00 ..2.. PROPERTIES Sl. No. Properties Unit Specification 1. Appearance Low viscous Liquid 2. Colour Colourless 3. Open Time Minutes 1 – 2 4. Viscosity @ 30°C (sp4, rpm30) cPs 850 – 1150 5. Specific gravity @ 28 30°C 0.85 ± 0.05 6. Non volatile content (at 105, 3 hrs) % 15.0 ± 1.5 7. Peel strength (after 1 day a. Leather Leather b. Leather Canvas Kg/25mm Min 2.0 Min 1.0 8. Lap shear strength (after 1 day) a. Leather Leather b. Leather Canvas c. Canvas Canvas d. Aluminium Aluminium e. Neoprene Neoprene f. Paper Paper g. Wood Wood h. Wood canvas Kg/cm2 Min 9.0 Min 5.0 Min 1.0 Min 4.0 Min 1.0 Substrates Failure Min 2.0 Min 4.0 SHELF LIFE : Six months from the month of manufacture. STORAGE : Store in cool dry place away from heat source and direct sunlight. PACKING : 7ml, 20ml, 60ml & 100 ml
Additional Information:
- Delivery Time: WITHIN 10 DAYS
- Packaging Details: 7 ML,20ML,60ML100 ML,
View Complete details
get quote
request a call back
Pidilite Fevibond
Rs 32 / NumberGet Best Price
Minimum Order Quantity: 200 Number
Product Brochure
| Brand | Pidilite |
| Model Number | FEVIBOND |
| Packaging Size | 50ML |
| Packaging Type | TUBE |
| Application Industry | Footwear, CRAFT |
| Surface Of Application | Rubber, Fabric |
| Form | LIQUID |
| Grade Standard | Industrial |
| Strength | High |
| Country of Origin | Made in India |
DESCRIPTION: FEVIBOND is a synthetic rubber based solvent containing contact adhesive. It exhibits immediate bond strength on contact of the two adhesive films on the to-be bonded surfaces. It is mandatory to apply this adhesive on both the surfaces to be bonded. The adhesive dries to a tough, flexible film with good resistance to water and aging. APPLICATION AREA: FEVIBOND is a multipurpose adhesive is used to bond flexible as well as rigid substrates. It exhibits outstanding bond to various types of rubbers such as Neoprene,Vulcanised, Microcellular Rubber, microcellular EVA, Painted metal, Mild steel , Glass, Galvanized steel, Chip board, Polyurethane foam, Polystyrene sheet, Leather, Leather board , GRP, Rigid PVC Boards etc. which are encountered in Electronics, Automotive, Vehicle Building, Electrical areas of different industries. It finds extensive application in Toy making and Handicrafts such as stuffed dolls industry. It is an excellent DIY tool. This adhesive is not recommended for non-polar substrates like Polyethylene, Polypropylene, Teflon, and Silicone rubber. Also remember not to apply this adhesive directly on substrates which get affected by solvents viz. Styrofoam (Thermocol). It is not suitable for highly plasticized PVC film. TYPICAL PHYSICAL PROPERTIES: APPEARANCE : LIGHT BROWN LIQUID SOLIDS CONTENT : Approx. 20 % VISCOSITY @ 300C : 16-20 Poise By Brookfield Viscometer RVT/Spindle #3/20 RPM OPERATING TEMPERATURE : - 200C to +800C (Short exposure up to 15 minutes to 1000C ) Note: The above values shall not be construed as product specification.
METHOD OF APPLICATION : 1. Clean the substrates to be bonded. Surfaces must be dry and free from dust, dirt, oil, grease, mould release agent and other contaminants. 2. Squeeze out the adhesive from the tube and apply uniformly on both the substrates to be bonded. Porous substrates may require a second coat, which can be applied after 5-10 minutes of first coat. 3. Allow to dry for 15-20 minutes at room temperature. The adhesive after drying exhibits tack. The finger test has proven itself to be a reliable method of judging the OPEN-TIME, whereas this time only serves as a rough indication, as variance may occur due to variation in temperature, relative humidity, type of substrates etc. In the finger test the adhesive must feel dry but tacky. 4. After appropriate OPEN-TIME bring both the substrates together, align them properly and press firmly for 2-5 seconds. The bonded components need not be kept under pressure fixture. 5. Allow the Adhesive to cure for 24-48 Hrs. SAFETY PRECAUTIONS: Keep the adhesive tube closed when not in use. The adhesive is flammable, hence smoking and naked-flame must be avoided in the working area. Store the adhesive in a cool (<300C) area. Proper ventilation must be provided on the shop-floor. SHELF LIFE: At least one year from the date of manufacture in sealed condition if stored under recommended storage conditions.
Additional Information:
- Delivery Time: IMMEDIATE
- Packaging Details: 8ML,25ML,50ML,90ML
View Complete details
get quote
request a call back
Polygrip S 709
Rs 1,100 / PackGet Best Price
Minimum Order Quantity: 20 Pack
Product Brochure
| Adhesive Type | Synthetic |
| Color | Dark Brown |
| Material | Synthetic Adhesive |
| Heat&Water Resistant | Max 30c |
| Temperature Range | Max 30C |
| Surface Of Application | Wood |
| Brand | Atul ltd |
| Grade Standard | Industrial Grade |
| Usage/Application | industrial |
| Form | Liquid |
description polygrip s-709 is a dark-brown coloured synthetic rubber based contact adhesive. It is a multipurpose adhesive suitable for bonding variety of substrates such as rubber, leather, eva, rexin, wood, laminate, painted ms, foam and canvas. Advantages ease of application with good coverage excellent tack good bond strength long lasting durable bond with excellent water resistance mild smell no harmful benzene applications automotive interiors footwear handicraft pvc flooring . Carpet lying sofa . Chair manufacturing upholstery and mattress typical specifications properties unit test method values appearance - visual dark-brown, medium viscous liquid density at 30°c g/ml - 0. 80 - 0. 84 viscosity at 30°c c ps astm d2196 1,000 - 1,500 tack retention time1 me minutes - max 30 1tack retention time (open time) is generally measured after evaporation of solvent once adhesive applied in thin film. It may vary depending upon ambient temperature and humid conditions. Process of application surface preparation: ensure that substrates to be bonded are clean, dry and free from oil, grease and foreign particles such as dust and rust. Application method: stir adhesive well and make it homogeneous prior to use. Apply adhesive uniformly in thin layer on both the substrates to be bonded with brush, spatula or any suitable tool. Allow evaporation of solvent from adhesive layer. The evaporation of solvent may take 5 minutes to 10 minutes, which depends upon ambient temperature and humidity. Assemble both the substrates with uniform contact pressure to achieve intimate contact without air pockets. The optimum bond strength is achieved after 24 hours. Packaging polygrip s-709 is available in 1 l, 2 l, 5 l, and 30 l ms drums. Other packing may be considered on request. Storage and handling polygrip s-709 should be stored in cool and dry place away from moisture, heat and direct sunlight. It contains highly volatile solvents, which will release during application, processing and use. These volatile solvents are highly flammable, hence adhesive must not come in contact with heat, spark and necked flame. This product has a shelf life of 1 year if stored in its original container between 2°c and 40°c away from humidity and excessive heat. Please refer to the safety data sheet (sds) for detailed instructions on storage and handling. Polygrip® s-709 technical data sheet . Polymers business september 2017 page 2 of 2 safety wear personal protective equipment (ppe). Avoid contact with the eyes and skin. In case of direct contact and irritation, it should be washed off immediately with soap and warm water. Proper ventilation must be provided to shop floor where adhesive is used. Avoid breathing vapours, mist or gas. Please refer to the sds for detailed safety instructions. Spills and disposal in case of spills, sweep up and shovel the spilled material. Keep spilled material in suitable, closed containers for disposal. Soak up with an absorbent such as clay, sand or other suitable material. Flush area with water to remove trace residue Do not allow the product to reach the sewage system Waste must be disposed of in accordance with federal, state or local regulations, as applicable
application : sofa,chair,automobile,
Additional Information:
- Delivery Time: within 2 days
- Packaging Details: 1 ltr,2 ltr,5 ltr.30 ltr
View Complete details
get quote
request a call back
Polygrip Mp 609
Rs 185 / LitreGet Best Price
Minimum Order Quantity: 24 Litre
Product Brochure
| Brand | ATUL LTD |
| Model Number | POLYGRIP MP 609 |
| Packaging Size | 1 LTR |
| Packaging Type | Tin Can |
| Application Industry | Footwear, Flooring, Laminating |
| Surface Of Application | Rubber, PVC, Fabric |
| Grade Standard | Industrial |
| Strength | High |
| Country of Origin | Made in India |
Description Polygrip MP-609 is a dark brown coloured synthetic rubber based contact adhesive. It is ageneral purpose adhesive suitable for bonding variety of substrates such as rubber, leather,EVA, rexin, foam and canvas. It is general purpose adhesive for flexible substrates.Advantages Adequate bond strengthEase of application with good coverageGood tack and tack retention timeMild smellModerate bond strengthNo harmful benzeneApplications Carpet layingFoam to foam bondingLeather articlesMattress and upholsteryTypical specifications Properties Unit Test method ValuesAppearance - Visual Dark-brown, low viscous liquidDensity at 30°C g/ml - 0.78 - 0.82Viscosity at 30°C c Ps ASTM D2196 400 - 800Tack retention time1 Minutes - Max 301Tack retention time (open time) is generally measured after evaporation of solvent once adhesive applied in thin film. Itmay vary depending upon ambient temperature and humid conditions.Process of application Surface preparation: Ensure that substrates to be bonded are clean, dry and free from oil,grease and foreign particles such as dust and rust.Application method: Stir adhesive well and make it homogeneous prior to use. Applyadhesive uniformly in thin layer on both the substrates to be bonded with brush, spatula orany suitable tool. Allow evaporation of solvents from adhesive layer to develop tack. Theevaporation of solvent may take 5 minutes to 10 minutes, which depends upon ambienttemperature and humidity. In case of absorbing substrate, apply second coat and allowdrying for 5 minutes to 10 minutes. Assemble both the substrates with uniform contactpressure to achieve intimate contact without air pockets. The optimum bond strength isachieved after 24 hours.Packaging Polygrip MP-609 is available in 0.5 L, 1 L, 2 L, 5 L and 30 L MS drums. Other packing maybe considered on request.Storage and handlingPolygrip MP-609 should be stored in cool and dry place away from moisture, heat and directsunlight. It contains highly volatile solvents, which will release during application, processingand use. These volatile solvents are highly flammable, hence adhesive must not come incontact with heat, spark and necked flame. This product has a shelf-life of 1 year if stored inits original container between 2°C and 40°C away from humidity and excessive heat. Pleaserefer to the Safety Data Sheet (SDS) for detailed instructions on storage and handling.
Additional Information:
- Delivery Time: IMMEIDIATE
- Packaging Details: 500ML,1LTR,5 LTR,30 LTR
View Complete details
get quote
request a call back
Super Bond SR 7X
Rs 170 / LitreGet Best Price
Minimum Order Quantity: 12 Litre
Product Brochure
| Grade Standard | Industrial Grade |
| Packaging Size | 1 Ltr , 5 Ltr , 30 ltr |
| Surface of Application | Plastic, Wood |
| Brand | Synthetic Rubber base Adhesive |
| Features | Impact Resistant |
| Color | brown |
SR7X
(FW) is medium grade yellow colour adhesive for footwear application. It is used in Leather, MCR,
EVA, Rubber, Synthetic Fibers etc. High coverage and cost effectiveness is a key point.
Method of use: -
1) The material to be bonded should be dry, clean and free of dust, oil or grease.
2) Using brush or spreader applies a thin coating of adhesive to both of the surfaces.
3) Allow the solvent content to evaporate before bonding the materials. The time for
evaporation will depend on the temperature and humidity. On absorbent or permeable
materials such as leather/ chipboard bonding may be possible within a matter of 23
minutes. Of application on non absorbent or no permeable materials a minimum of 15
minutes should elapse before the surfaces are bonded.
4) Bond the materials under firm pressure.
5) Dried coating of Superbond SR7X
(FW) may be reactivated by wiping over the surface with
suitable solvent.
Properties: -
1) Appearance : Yellowish
Brown Viscous Liquid.
2) Viscosity : 900
cPs to 1100 cPs @300C+20C
4) Coverage : 30
to 35 pairs per liter.
5) Shelf Life : One
year from date of manufacturing in the sealed container.
6) Tack Time : 30
minutes minimum.
Additional Information:
- Pay Mode Terms: T/T (Bank Transfer)
- Delivery Time: within week
View Complete details
get quote
request a call back
Fevicol Sr 998 Rubber Adhesive
Rs 413 / LitreGet Best Price
Minimum Order Quantity: 20 Litre
Product Brochure
| Brand | Fevicol |
| Model Number | SR 998 |
| Packaging Size | 1 LTR |
| Packaging Type | DABBA |
| Application Industry | Automotive, Packaging |
| Surface Of Application | Plastic, Metal |
| Grade Standard | Industrial |
| Strength | High |
| Country of Origin | Made in India |
echnical Specification
- Appearance: Dark brown liquid.
- Viscosity: 20 P to 25 P.
- Specific gravity: 0.85 to 0.90.
- Solids: 23%
- Diluent/ Cleaner: Toluene.
- Drying time: Minimum 5 minutes.
- Tack retention time: Minimum 30 minutes.
- Peel strength: Minimum 2 kg/inch.
- Product Features
- Free from benzene makes it non-hazardous
- Excellent strength
- Superior resistance to water
- Fast drying
Additional Information:
- Delivery Time: IMMEDIATE
- Packaging Details: 500ML.1LTR,5LTR,30 LTR
View Complete details
get quote
request a call back
Super Bond SR 5X
Rs 170 / LitreGet Best Price
Minimum Order Quantity: 24 Litre
| Grade Standard | Pharmaceutical Grade, Industrial Grade |
| Packaging Size | 1 Ltr , 5 Ltr , 30 Ltr |
| Surface of Application | Wood, Paper, Plastic |
| Brand | Rubber Base Adhesive |
| Features | Impact Resistant, Moisture Resistant, Vibration Resistant |
| Color | Brown |
Additional Information:
- Pay Mode Terms: T/T (Bank Transfer)
- Delivery Time: Within week
- Packaging Details: 1 ltr, 5 Ltr,30 Ltr
View Complete details
get quote
request a call back
Super Bond SR 9X
Rs 210 / UnitGet Best Price
Minimum Order Quantity: 20 Unit
| Grade Standard | Industrial Grade |
| Packaging Size | 5 ltr |
| Surface of Application | Plastic, Ceramic, Wood, Paper |
| Features | Impact Resistant, Moisture Resistant, Vibration Resistant |
| Color | brown |
| Material | Synthetic Rubber base Adhesive |
Formulated to be used in heavy-duty applications like wood working and is highly suitable for other applications like foam, synthetic fabrics, leather, mattresses, automotive interiors and many others.
Additional Information:
- Pay Mode Terms: T/T (Bank Transfer)
- Delivery Time: within week
- Packaging Details: 1 ltr,5 ltr,30 ltr
View Complete details
get quote
request a call back
POLYGRPIP PLUS 909
Rs 305 / LitreGet Best Price
Minimum Order Quantity: 24 Litre
Product Brochure
| Brand | ATUL LTD |
| Model Number | POLUGRIP PLUS 909 |
| Packaging Size | 1 LTR |
| Packaging Type | Tin Can |
| Application Industry | Laminating, Footwear, Flooring |
| Surface Of Application | Rubber, Fabric, PVC |
| Grade Standard | Industrial |
| Strength | High |
| Country of Origin | Made in India |
Description Polygrip plus-909 is a brownish-yellow synthetic rubber based contact adhesive. It is high strength premium adhesive suitable for bonding variety of substrates which includes rubber, leather, EVA, wood, laminate, concrete, FRP, painted MS, foam, rexin and canvas. Advantages Ease of application with good coverage Excellent tack quality High bond strength Long lasting durable bond with excellent water resistance Mild smell No harmful benzene Applications Automotive interiors Footwear Furniture manufacturing (plywood to laminate) Handicraft HVAC applications - AC ducting, chilled water piping and under deck insulation PVC flooring | carpet lying Upholstery and mattress Typical specifications Properties Unit Test method Values Appearance - Visual Brownish-yellow viscous liquid Density at 30°C g/ml - 0.83 - 0.89 Viscosity at 30°C c Ps ASTM D2196 1,800 - 2,600 Tack retention time1 Minutes - Max 30 1Tack retention time (open time) is generally measured after evaporation of solvent once adhesive applied in thin film. It may vary depending upon ambient temperature and humid conditions. Process of application Surface preparation: Ensure that substrates to be bonded are clean, dry and free from oil, grease and foreign particles such as dust and rust. Application method: Stir adhesive well and make it homogeneous prior to use. Apply the adhesive first on non-porous surface and then on porous surface. Apply adhesive uniformly in thin layer on both the substrates to be bonded with brush, spatula or any suitable tool. Allow evaporation of solvent from adhesive layer. The evaporation of solvent may take 5 minutes to 10 minutes, which depends upon ambient temperature and humidity. Assemble both the substrates with uniform contact pressure to achieve intimate contact without air pockets. The optimum bond strength is achieved after 24 hours. Packaging Polygrip plus-909 is available in 0.1 L, 0.2 L, 0.5 L, 1 L, 2 L, 5 L, and 30 L MS drums. Other packing may be considered on request. Storage and handling Polygrip plus-909 should be stored in cool and dry place away from moisture, heat and direct sunlight. It contains highly volatile solvents, which will release during application, processing and use. These volatile solvents are highly flammable, hence adhesive must not come in contact with heat, spark and necked flame. This product has a shelf-life of 1 year if stored in its original container between 2°C and 40°C away from humidity and excessive heat. Please refer to the Safety Data Sheet (SDS) for detailed instructions on storage and handling.
Additional Information:
- Delivery Time: AVAILABLE
- Packaging Details: 100ML,200ML,500ML,1LTR,2LTR,5LTR,30 LTR
View Complete details
get quote
request a call back
SP6 Rubber Adhesive
Rs 230 / LitreGet Best Price
Minimum Order Quantity: 20 Litre
Product Brochure
| Product | Fevicol SP6 |
| Max.Tack retention time | 10-15 |
| Full cure | 24 Hrs |
| Temperature Resistance | -20 to +120 |
| Applications | Highest heat resistance suitable for critical applications requiring Thermocycle resistance. |
| Type | Slow Drying |
| Colour | Dark Brown Liquid |
| Solid Content | 19-20% |
| Viscosity | 150-250 |
| Minimum Peel Strength | 1.8 Kg/inch |
| Drying time | 2-3 |
PRICE : 18 % GST INCLUDING.
PIDILITE INDUSTRIES LIMITED
Marketing Division: P.B. No. 17411, Andheri (East), Mumbai 400 059 (India)
TECHNICAL DATA SHEET
PRODUCT : FEVICOL SP ?? 6
Description : Fevicol SP-6 is a synthetic rubber (polychloroprene) based solvent borne
contact adhesive. The adhesive dries to a tough flexible film with good resistance to heat and
ageing. Fevicol SP-6 is suitable for spray application. It demonstrates fast initial strength and
good contact capability. When used as two-way adhesive the open-time for assembly is not a
constraint, but when considered for one-way application the assembly should be done within
very short time.
TYPICAL PROPERTIES :
Sr.No. PROPERTIES UNIT TYPICAL DATA
1 APPEARANCE Yellowish Brown Liquid
2 SOLIDS CONTENT % 20 +/- 2
3 VISCOSITY @ 30oC By B/F
Viscometer RTV/Spindle# 1/20RPM Centi Poise 150 +/- 20
4 DRYING-TIME, Minutes Minutes : 2 ?? 3 Maximum
5 TACK RETENTION TIME Minutes 25 Maximum
6 SOFTENING TEMPERATURE,
with 500 gm load by JISK Method
oC 120 Minimum
7 PEEL- STRENGTH Kg/inch measured @ R.T.
i) Initial 1.5 Minimum
ii) After 24 Hrs.@ R.T. 1.8 Minimum
iii) After 24 Hrs.@ R.T.followed by
24Hrs.@ 80oC 2.0 Minimum
8 HEAT CREEP TEST @ 80oC, for 10 minutes (80 mm max.)
I) After 24 Hrs.@ R.T. Kg 0.9
ii) After 24 Hrs.@ R.T.followed by 24
hrs at 80 DegC. Kg 1
NOTE : 1. Substrates used for Softening ?? Temperature, Peel Strength & Heat Creep Test are :
Painted M.S. & both side cloth lined PU Foam.
2. For test parameters refer the Detailed Test Procedures.
pdfMachine
Is a pdf writer that produces quality PDF files with ease!
Produce quality PDF files in seconds and preserve the integrity of your original documents. Compatible across
nearly all Windows platforms, if you can print from a windows application you can use pdfMachine.
Get yours now!
:2:
APPLICATION AREAS : Fevicol SP-6 is a multipurpose adhesive and suitable for the
automotive industry as a high performance trim adhesive. It forms a strong permanent contact
bond between the following materials : Painted steel, Plywood, Chipboard, Polyurethane foam,
Muslin, Foam rubber, Felt, supported PVC sheet Fabrics, Leather etc. It will not bond plastics
like Teflon, Polythene & it should never be directly applied on substrates affected by solvents
like Thermocol.
METHOD OF APPLICATION :
1. The substrates to be bonded must be clean, dry free from oil, grease etc. Trichloroethylene
/ Acetone may be used for Cleaning.
2. Apply uniform coat of adhesive on both substrates to be bonded, using an air supported
spray-gun with 1.6 ??2.0 mm nozzle orifice from a distance of 2-3 feet at 3.5 ??5.0 Kg/cm2 air
pressure.
3. Allow to dry for a minimum of 5 minutes. Bring both the substrates together with perfect
alignment and press firmly. Sufficient pressure is mandatory to obtain satisfactory
coalescence of the two adhesive films. The contact bond offers sufficient initial strength for
immediate handling. The bonded assembly need not be kept under pressure. The bond
cures further and attains peak strength in 3-4 days.
SAFETY PRECAUTIONS : Store the containers in well sealed condition away from heat and
source of combustion or sparks. Proper ventilation must be provided on the shop-floor. A
detailed MSDS is available on request.
SHELF-LIFE : This product will remain suitable for it??s intended purpose for up to 12 months
when stored under recommended conditions in the original sealed container.
View Complete details
get quote
request a call back
Fevicol Sr 998 Is Sr Adhesive
Rs 300 / LitreGet Best Price
Minimum Order Quantity: 20 Litre
Product Brochure
| Brand | PIDILITE IND LTD |
| Types | RUBBER BASE ADHESIVE |
| Material Compatibility | SOLVENT BASE |
| Packing Type | TIN |
| Origin | Synthetic |
| Grade Standard | Industrial Grade |
| Curing Method | Heat Activated Curing |
| Classification | ATMOSPHERE |
| Color | BROWN |
| Weight | 1 LTR |
| Purity | BROWN |
| Shelf Life & Storage | 1 YEAR |
| Packaging Size | 1 LTR |
| Packaging Type | TIN |
PRODUCT : FEVICOL SR998 IS
DESCRIPTION: FEVICOL SR998 IS is a synthetic rubber based solvent containing
contact adhesive specially designed for Industrial segment. It exhibits excellent
bonding strength. The adhesive dries to a tough, flexible film with good resistance to
water and aging. This adhesive can be applied by brush, or roller coater.
SALIENT FEATURES :
Free from Benzene- Non-hazardous to health.
Excellent Strength.
Preferred by the users dealing only in quality works.
APPLICATION AREA: FEVICOL SR998 IS is used to bond variety of substrates in
painted metal, Mild steel, glass, galvanized steel, chip board, PU sheet, leather, leather
board, cementious flooring , GRP, Rigid PVC board, synthetic fabrics etc which are
encountered in Automotive , Railway, Vehicle building, Construction & Electrical areas
of ship-building and many other industries. This adhesive is not recommended for
non-polar substrates like Polythene,Teflon. Also remember not to apply this adhesive
directly on substrates which get affected by solvents viz. Styrofoam(Thermocol).
TYPICAL PHYSICAL PROPERTIES:
Sr.No Properties Unit Typical Data
1 Appearance --- Dark Brown Liquid
2 Viscosity at 30 oC ( By Brookfield
viscometer RVT/Spindle #3/20 RPM )
Poise 20 – 25 Poise
3 Specific gravity at 30 oC gm/ml 0.85 – 0.90
4 % Solids % 23
5 Diluent/Cleaner -- Toluene
6 Flash point -- 00c to 40c
7 Drying time Minutes. 5-10 approx
8 Tack retention time Minutes. 45
pdfMachine
A pdf writer that produces quality PDF files with ease!
Produce quality PDF files in seconds and preserve the integrity of your original documents. Compatible across
nearly all Windows platforms, if you can print from a windows application you can use pdfMachine.
Get yours now!
APPLICATION INSTRUCTIONS :
Proper surface preparation is important to get optimum & consistent results.
Surfaces must be dry and free from dust, dirt, oil & grease, mould release agent
and other contaminants.
Stir well the contents till homogeneous
Apply the adhesive uniformly on both the substrates to be bonded by
brush or appropriate applicator. Porous substrates may require a second coat,
which can be applied after 5-10 minutes of first coat.
Allow to dry for 15-20 minutes at room temperature. The adhesive after
drying exhibits tack. The finger test has proven itself to be a reliable
method of judging the OPEN-TIME. Whereas this time only serves as a
rough indication , variance may occur due to temperature, relative
humidity, type of substrates etc. In the finger test the adhesive must feel
dry but tacky. The substrates bonded after prolonged open-time & in the
absence of tack may result in inferior coalescence & bond strength.
.
After appropriate OPEN-TIME( which is the span between Drying-time & Tack
Retention Time) bring both the substrates together, align them properly and press
firmly to obtain a uniform contact pressure. The bonded components need not be
kept under pressure fixture.
?????? The full bond strength builds up further in 24hrs to 48hrs after application.
Coverage : Approx 250-350 gms per square meter on non porous substrates.
However coverage quantity may vary on porous substrates like wood, leather etc.
SHELF LIFE : One year from the date of manufacture when stored in sealed container
Packing : 1 Lit.,5 Lit., 25 Lit.
Additional Information:
- Delivery Time: READY STOCK
View Complete details
get quote
request a call back
Polygrip SR 409 Rubber Adhesive
Rs 220 / LitreGet Best Price
Minimum Order Quantity: 20 Litre
Product Brochure
| Brand | polygrip |
| Model Number | polygrip sr 409 |
| Packaging Size | 1 ltr |
| Packaging Type | Tin Can |
| Country of Origin | Made in India |
DescriptionPolygrip SR 409 is light yellow colored fast drying synthetic rubber based contact adhesive. It is specially designed for foam to foam bonding in the manufacturing of sofa, chair & mattress. It exhibits soft and flexible glue line on the bonded substrates. It provides excellent film forming ability on various foams and provides high tack & immediate bonding which results in faster productivity.Advantages Mild smellFaster drying Light colored Excellent tack No harmful benzene Low absorption on foam surfaceApplications Sofa, mattress & chairs manufacturing
Typical specifications Properties Unit Test method Values Appearance Visual Light yellow viscous liquid Density at 30C g/ml 0.80 - 0.85 Viscosity at 30C cPs ASTM D 2196 800 - 1000 *Tack retention time Minutes Max. 30* Tack retention time (pen time) is generally measured after evaporation of solvent once adhesive applied in thin film. It may vary depending upon ambient temperature & humidity conditions.
Process of application(1) Surface preparation Ensure that substrates to be bonded are clean, dry and free from oil, grease and foreign particles such as dust and rust(2) Application Method Stir adhesive well and make it homogeneous prior to use Apply adhesive uniformly in thin layer on both the substrates to be bonded with brush, spatula or any suitable tool Allow evaporation of solvents from adhesive layer to develop tack. The evaporation of solvent may take 2-3 minutes, which depends upon ambient temperature and humidity.Assemble both the substrates with uniform contact pressure to achieve intimate contact without air pockets. The optimum bond strength is achieved after 24 hrs.PackagingPolygrip SR 409 is available in 1, 5 and 30 liters MS drums. Other packing may be considered on request.
Storage and handlingPolygrip SR 409 should be stored in cool & dry place away from moisture, heat & direct sunlight. It contains highly volatile solvents, which will release during application, processing and use. These volatile solvents are highly flammable, hence adhesive must not come in contact with heat, spark and necked flame. This product has a shelf life of 1year if stored in its original container between 2C and 40C away from humidity and excessive heat.SafetyWear personal protective equipment (PPE). Avoid contact with the eyes and skin. In case of direct contact and irritation, it should be washed off immediately with soap and warm water. Proper ventilation must be provided to shop floor where adhesive is used. Avoid breathing vapours, mist or gas. Please refer to the Safety Data Sheet (SDS) of Polygrip SR 409 for detailed safety instructions.Spills and disposalIn case of spills, sweep up and shovel the spilled material. Keep spilled material in suitable, closed containers for disposal. Soak up with an absorbent such as clay, sand or other suitable material. Flush area with water to remove trace residue. Do not allow the product to reach the sewage system. Waste must be disposed of in accordance with federal, state or local regulations, as applicable.
Additional Information:
- Production Capacity: AVAILABLE
- Delivery Time: WHTIHN TWO DAYS
- Packaging Details: 500ML, 1,2.5,25 LTR
View Complete details
get quote
request a call back
SRNLFW Synthetic Rubber Adhesive
Rs 185 / LitreGet Best Price
Minimum Order Quantity: 20 Litre
Product Brochure
| Product | SRNLFW |
| Color | Dark Brown Liquid |
| Solid Content | 20-21% |
| Viscosity | 18-22 |
| Temperature Resistance | -20 to +80 |
| Applications | Rail coaches, door trims, vehicle maintenance. |
SR7X
(FW) is medium grade yellow colour adhesive for footwear application. It is used in Leather, MCR,
EVA, Rubber, Synthetic Fibers etc. High coverage and cost effectiveness is a key point.
Method of use: -
1) The material to be bonded should be dry, clean and free of dust, oil or grease.
2) Using brush or spreader applies a thin coating of adhesive to both of the surfaces.
3) Allow the solvent content to evaporate before bonding the materials. The time for
evaporation will depend on the temperature and humidity. On absorbent or permeable
materials such as leather/ chipboard bonding may be possible within a matter of 23
minutes. Of application on non absorbent or no permeable materials a minimum of 15
minutes should elapse before the surfaces are bonded.
4) Bond the materials under firm pressure.
5) Dried coating of Superbond SR7X
(FW) may be reactivated by wiping over the surface with
suitable solvent.
Properties: -
1) Appearance : Yellowish
Brown Viscous Liquid.
2) Viscosity : 900
cPs to 1100 cPs @300C+20C
4) Coverage : 30
to 35 pairs per liter.
5) Shelf Life : One
year from date of manufacturing in the sealed container.
6) Tack Time : 30
minutes minimum.
View Complete details
get quote
request a call back
SP5 Sprayable Rubber Adhesive
Rs 850 / PIECEGet Best Price
Minimum Order Quantity: 20 PIECE
| Product | Fevicol SP5 |
| Max.Tack retention time | 10-15 min |
| Full cure | 24 Hrs |
| Temperature Resistance | -20 to + 105 |
| Applications | Higher heat resistance makes it suitable for door trim |
| Type | Slow Drying |
| Colour | Reddish Brown Liquid |
| Solid Content % | 19-20 |
| Viscosity | 120-160 |
| Minimum Peel Strength | 1.5 Kg/inch |
| Drying time | 2-3 min |
Details:
- It is a synthetic rubber-based solvent containing contact adhesive.
- It develops initial strength quickly and has good contact ability.
- The adhesive dries to a tough, flexible, plastic film with good resistance to water and ageing.
Salient Features & Benefits:
- Single component, free from toxic solvents like benzene, dichloro-ethane, methanol
- Good tack/grab with adequate tack retention time
- Bond both flexible and rigid substrates
- Exhibits outstanding bond to porous, non-porous substrates encountered in automotive, railway, vehicle building, construction, electrical areas of shipbuilding and many other industries
View Complete details
get quote
request a call back
Fevicol Heatx Heat Proof Adhesive
Rs 202 / NumberGet Best Price
Minimum Order Quantity: 20 Number
| Country of Origin | Made in India |
GST 18% INCLUDING ABOVE PRICE.
Fevicol HeatX is a synthetic solvent borne rubber based adhesive made with a special formula for having excellent heat resistance property up-to 170°C temperature. Fevicol HeatX is having Excellent heat resistance & Quick grab property without spring back action on curved surface, and this property is helpful in vertical applications.
| Compatible Material | Wood |
| Colour | Yellow |
| Brand | Pidilite |
| Container type | Can |
| Item Volume | 1 Litres |
- HEAT RESISTANCE - High Heat resistance capacity up to 170 deg Good for Heat prone areas like kitchen burner or dining table top.
- EFFECTIVE & EFFICIENT - Bonds in 10-15 min Faster Completion of Carpentry. Faster Completion of work Faster Setting time: 2 hrs and saves labour.
- FAST BONDING - Fast Bonding, Grip & No Spring Back Action Best results in Vertical Applications & executing Complicated designs.
- INSIDE LAMINATIONS - One of the best usages of HeatX is for Andarwala laminate i.e. for inside lamination of cabinets & storages. No constant pressure & masking tape required Best for Inside Laminate of shutters.
- IDEAL - Ideal for Vertical applications.
| Brand Name | Pidilite | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Colour | Yellow | ||||||||||
| Compatible Material | Wood | ||||||||||
| Full Cure Time | 15-20 minutes | ||||||||||
| Item Volume | 1 liters | ||||||||||
| Manufacturer Series Number | DHR_040 | ||||||||||
| Material | adhesives; sealants | ||||||||||
Model Number
|
Additional Information:
- Delivery Time: IMMEDIATE
- Packaging Details: ALL PACKING AVAILABLE
View Complete details
get quote
request a call back
Synthetic Rubber Adhesive Fevicol Foam Fix
Rs 250 / NumberGet Best Price
Minimum Order Quantity: 20 Number
| Country of Origin | Made in India |
PRICE IS INCLUDING GST 18%.
Product Description
We are among the celebrated organizations in the industry for offering a wide range of Synthetic Rubber Adhesive Fevicol Foamfix in the market at very affordable rates.
Features:
Accurate in composition
Highly effective
No side effects
Accurately formulated
Proper chemical properties
Safe to use
Additional Information:
- Delivery Time: IMMEDIATE
- Packaging Details: 500ML,1LTR,2 LTR,5LTR,
View Complete details
get quote
request a call back
SR 1900M Synthetic Rubber Adhesive
Rs 160 / LitreGet Best Price
Minimum Order Quantity: 26 Litre
| Product | Fevicol SR 1900M |
| Color | Light Yellow Liquid |
| Solid Content | 22-23% |
| Viscosity | 20-25 |
| Drying time | 10 min |
| Max.Tack retention time | Max 30 min |
| Full cure | 24 Hrs |
| Temperature Resistance | -20 to +80 |
| Applications | Rail coaches, door trims, vehicle maintenance |
- Single component, free from toxic solvents like benzene, dichloro-ethane, methanol
- Good tack/grab with adequate tack retention time
- Bond both flexible and rigid substrates
- Exhibits outstanding bond to porous, non-porous substrates encountered in automotive, railway, vehicle building, construction, electrical areas of shipbuilding and many other industries
View Complete details
get quote
request a call back
Polygrip Hotbond
Rs 350 / LitreGet Best Price
Minimum Order Quantity: 20 Litre
| Brand | ATUL LTD |
| Model Number | POLYGRIP HOTBOND |
| Packaging Size | 1 LTR |
| Packaging Type | Tin Can |
| Application Industry | Laminating, Flooring |
| Surface Of Application | Rubber, PVC, Fabric |
| Grade Standard | Pharmaceutical |
| Strength | High |
| Country of Origin | Made in India |
DescriptionPolygrip Hotbond is light yellow colored, fast drying synthetic rubber based adhesive. It is specially designed adhesive which can provide heat resistant up to 170°C. It provides excellent tack and instant bonding to most demanding application of furniture industry. It is most suitable for curved, spherical and round surface for quick bonding without spring back action.Advantages Mild smell??? Excellent coverage No harmful benzene Heat resistant up to 170°C Fast drying and instant bonding Instant strength developmentApplications In furniture industry for bonding of below substrates Ply to Laminate??? Laminate to Laminate Ply to PVC laminate??? Metal to LaminateTypical specifications Properties Unit Test method Values Appearance -- Visual Light yellow Density at 30ºC g/ml -- 0.84 - 0.89 Viscosity at 30ºC cPs ASTM D 2196 2200 - 3000 *Tack retention me Minutes -- Max. 10* Tack retention time (open time) is generally measured after evaporation of solvent once adhesive applied in thin film. It may vary depending upon ambient temperature & humidity conditions.Process of application(1) Surface preparation??? Ensure that substrates to be bonded are clean, dry and free from oil, grease and foreign particles such as dust and rust(2) Application Method Stir adhesive well and make it homogeneous prior to use Apply the adhesive first on non-porous surface and then on porous surface Apply adhesive uniformly in thin layer on both the substrates to be bonded with brush, spatula or any suitable tool Allow evaporation of solvent from adhesive layer. The evaporation of solvent may take 3-5 minutes, which depends upon ambient temperature and humidity Assemble both the substrates with uniform contact pressure to achieve intimate contact without air pockets The optimum bond strength is achieved after 24 hrsPackagingPolygrip Hotbond is available in 0.2, 0.5 and 1 liters MS drums. Other packing may be considered on request.Storage and handlingPolygrip Hotbond should be stored in cool & dry place away from moisture, heat & direct sunlight. It contains highly volatile solvents, which will release during application, processing and use. These volatile solvents are highly flammable, hence adhesive must not come in contact with heat, spark and necked flame. This product has a shelf life of 1 year if stored in its original container between 2°C and 40°C away from humidity and excessive heat.
Additional Information:
- Delivery Time: IMMEDIATE
- Packaging Details: 500 ML,500ML,1 LTR,5 LTR
View Complete details
get quote
request a call back
FEVICOL ACP FIXX
Rs 194 / PieceGet Best Price
Minimum Order Quantity: 24 Piece
Product Brochure
| Color | White |
| Brand | pidilite ind ltd |
| Model Number | FEVICOL ACP FIXX |
| Packaging Size | 280 ml |
| Packaging Type | CARTRIDGE |
| Application Industry | Jointing |
| Surface Of Application | Plastic, Metal, Ceramic |
| Form | PASTE |
| Grade Standard | Industrial |
| Strength | High |
| Material Compatibility | Plastic, Metal, Ceramic |
FEVICOL ACP FIXX of the nailing required by providing quick grab and early high strength and strong holding. TYPICAL PROPERTIES: - Appearance: - Buff to Creamish Brown colored Thick Paste. Extrusion from Cartridge with Metal Gun: - Easy continuous flow from nozzle Specific Gravity: 1.15 +/- 0.05 Viscosity: - Approx. 180000 Cps @ 25 C using 7 Spindle, 10 RPM. Key Features • Extremely high initial grab • Provides a long lasting elastic bond. • FOR INFORMATION ONLY Fevicol ACP FIXX is multipurpose professional quality contact adhesive sealant which eliminates much Water resistance- will not break down in intermittent contact with water • High strength adhesive sealant • Strong vertical hold • Suitable for interior and exterior use • Will not discolor many types of mirrors • Temperature resistance • Noncorrosive RECOMMENDED USE: • Bonding PVC, Wood, Masonry, Aluminium, Galvanised Iron, Steel, Fibrous Cement Sheet and Floor Paneling etc. • Bonding Foamed Polystyrene, Polyurethane and Ceramic Tiles. • Use in ACP Panel for Shop Board Preparation and Paneling job in Mall, Restaurant / Hotel.
• Mirrors to Plywood, Ceramic and Plain Wall. • Installing particle board, fiber cement board, plaster board, plywood and strip flooring to Beam / Pillar and also for skirting boards. • Bonding Fiber Cement sheet (for e.g. Bison Board), Ceramic tiles and Wall paneling to Wooden panels (Plywood / Block Board / Solid Wood) • Sealing gap for variety of construction materials APPLICATION INSTRUCTIONS: Fevicol ACP FIXX adhesive sealant can be applied either by 1-WAY WET STICK ADHESIVE SEALANT METHOD or 2-WAY CONTACT METHOD: In both the cases the first requirement is that both surfaces to be bond must be clean, dry and free of grease, oil and dust. 1-WAY WET STICK ADHESIVE SEALANT METHOD: RECOMMENDED FOR HEAVIER OBJECTS . Apply 4-6mm bead Fevicol ACP FIXX to one surface, beads should not be 45mm apart. screwing to maintain maximum surface contact at bonded interface. Clean off excess adhesive sealant with acetone, mineral turpentine or toluene. Temporary fastening can be release after 24 hours. 2-WAY CONTACT METHOD: Apply 4-6mm bead adhesive sealant to one surface and bring both the substrate together. Bring two substrates together and apply pressure by temporary fastening like clamp, nailing or Press firmly over entire surface so as to transfer adhesive sealant and keep in contact for 45 seconds to 60 seconds then pull both surfaces apart. Allow it to dry for 3-5 minutes. Reposition and press the panel firmly together. Note :- In case of larger application area, apply holding pressure by temporary fastening like clamp, nailing or screwing to maintain maximum surface contact at bonded interface. Storage :- Material should be stored in a Dry and Cool place between +5 0 C to + 50 0 C. Shelf Life: - 12 Months from the date of manufacturing.
Additional Information:
- Delivery Time: WHITHIN TWO DAYS
- Packaging Details: 24 NO
View Complete details
get quote
request a call back
EXPLORE MORE CATEGORIES