Lube Adhesive & Engineering Co.
Lube Adhesive & Engineering Co.
Ghodasar, Ahmedabad, Gujarat
SEND SMS
SEND EMAIL

Thread Sealing Adhesive

Providing you the best range of hylomer universal blue, loctite 567 thread sealant, loctite 577 thread sealant, loctite 542 thread sealant, fasto a742 thread sealing adhesive and fasto a777 thread sealing adhesive with effective & timely delivery.

Hylomer Universal Blue

Hylomer Universal Blue
  • Hylomer Universal Blue
  • Hylomer Universal Blue
Get Best Quote
Approx. Price: Rs 540 / NumberGet Latest Price

Product Details:

Minimum Order Quantity10 Number
Usage/Applicationmetal to metal & plastic to plastic
Packaging Size100 gm
Brandhylomer
ColorBLUE
Density0,015mm
Model Name/NumberHYLOMER
Grade StandardIndustrial Grade
TypePASTE
Main Raw MaterialFLANGE JOINT
Surface Of ApplicationFLANGE JOINT
FormPASTE
MaterialPOLYSTER URATHENE
Type Of Silicone SealantTHREAD SEALAING
HardnessNON HARDNESS
StrengthGODD
Temp. Resistance-50 TO 250
Temperature-50 TO 250
Cure TimeNON SETTING
Fixture TimeNON FIXTURE
hylomer540

HYLOMAR UNIVERSAL BLUENon-setting gasket compoundDescriptionHylomar Universal Blue is a polyester urethane based sealant that is non-setting and nonhardeningeven at high temperatures. The compound is resistant to a wide range of fluids includingall industrial fuels, oils, water and brine, air, turbine and piston engine combustion products, water,water/glycol and methanol mixtures, petroleum and synthetic diester lubricating oils, gasoline andkerosene fluids (Avtur & Avcat) and fluorocarbon refrigerants. Hylomar Universal Blue can be usedto seal joint faces or threaded parts.Physical PropertiesChemical Basis Polyester UrethaneTemperature range -50°C to 250°CLIGHT GRADEFilm Thickness 0.015 mmSurface Finish Max 2.0 μmArea covered by 100g 1.875m²Product coverage after drying 2mg/cm²MEDIUM GRADEFilm Thickness 0.03 mmSurface Finish Max 3.0 μmArea covered by 100g 1.275m²Product coverage after drying 4mg/cm²HEAVY GRADEFilm Thickness 0.09 mmSurface Finish Max 3.5 μmArea covered by 100g 0.56m²Product coverage after drying 12mg/cm²Instructions for useHylomar Universal Blue should be applied to clean dry surfaces. Apply a thin film or bead to one orboth surfaces. Once applied, sufficient time should be allowed for the solvent to evaporate. Unlimitedassembly time allows precise alignment of joints to be made. Due to the nature of the compound,fasteners may be required to be re-tightened to the correct torque.Hylomar Universal Blue can be removed from dismantling components by rubbing with a cloth soakedwith Easy Clean Solvent, Hylomar Gasket Remover or Hylomar Rally and Grand Prix Wipes. Noscraping is necessary.
Typical ApplicationsHylomar Universal Blue enables the effective sealing of metal to metal and plastic to plasticcomponents. Typical applications include water and oil pumps, instrument inspection covers,cylinder heads and sumps, and it can also be used for the coating for pre-formed gaskets, weatherproofing, motors and outdoor high voltage circuit breakers. Inlet manifolds, timing case covers, oilpump joints, gear box and transmission components or thread sealing it has also been successfullybeen used in the assembly of gas turbines, water cool generators and turbo vacuum systems.There is no staining of copper and silver, etc., from traces of volatiles at elevated temperature, andis therefore suitable for joints, and threads in close proximity to switch mechanisms, etc.Light grade: inlet manifolds, timing case covers, oil pump joints, gearbox and transmissioncomponents, thread sealing and any finely machined surface.Medium grade: water and oil pumps, instrument inspection covers, cylinder heads, sumps andmost machined surfaces.Heavy grade: gas turbines, water cooled generators, turbo vacuum systems, gearboxes and mostrough machined surfaces.Handling and Safety PropertiesThe compound is non-flammableProduct contains DichloromethaneLabelling = Harmful. Carc cat 3. Phrases R40, S2, S23, S24/25 & S36/37.PackagingHylomar Universal Blue is available in 40 g tube, 100 g tube, 350 g cartridge, 250 ml brush top tin, 1litre screw top tin, 5 litre screw top tin, 6.5 kg lever lid tin, 25 kg kegs and aerosols. For Technical Dataon the Hylomar Universal Blue Aerosol Grade see separate Data sheet.The shelf life of Hylomar Universal Blue is 24 months when stored in unopened original containersbetween 5° and 25°C.For further information please contact our sales department
Request
Callback


Additional Information:

  • Item Code: Hylomer
  • Production Capacity: available
  • Delivery Time: within two day
  • Packaging Details: 100 gm
Yes! I am Interested
View PDF

LOCTITE 567 THREAD SEALANT

LOCTITE 567 THREAD SEALANT
  • LOCTITE 567 THREAD SEALANT
Get Best Quote
Approx. Price: Rs 770 / TUBEGet Latest Price

Product Details:

Minimum Order Quantity5 TUBE
Grade StandardIndustrial Grade
BrandLOCKTITE
Packaging Size50 ML
Usage/ApplicationCeramic
Packaging TypeBOTTLE
ViscosityHigh
TypeSEALANT
CapacityHIGH
StrengthLOW
Temperature RangeWORKING 205 C
Pressure13790 KPA
MaterialPASTE
Temperature ResistanceGRETHER THEN 460 C
Common ApplicationsSEALING

PRODUCT DESCRIPTION LOCTITE® 567™ provides the following product characteristics: Technology Acrylic Chemical Type Methacrylate ester Appearance (uncured) Smooth, creamy, off-white pasteLMS Components One component - requires no mixing Viscosity High Cure Anaerobic Secondary Cure Activator Application Thread sealing Strength Low This Technical Data Sheet is valid for LOCTITE® 567™ manufactured from the dates outlined in the "Manufacturing Date Reference" section. LOCTITE® 567™ is designed for the locking and sealing of metal tapered threads and fittings. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The high lubricating properties of this compound prevent galling on stainless steel, aluminum and all other metal pipe threads and fittings. The product offers high temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids. LOCTITE® 567™ is recommended for industrial applications in the chemical processing, petroleum refining, pulp/paper, waste treatment, textile, utilities/power generation, marine, automotive, industrial equipment, gas compression and distribution industries. It is also recommended for industrial plant fluid power systems. UL Classification Classified by Underwriters Laboratories Inc.® MH8007 - Fire hazard is small. No flash point in liquid state. Ignition temperature 455°C. For use in devices handling gasoline, petroleum oils, natural gas (pressure not over 300 PSIG), butane and propane not exceeding 2 in. pipe size. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification.
ULC Classification Classified by Underwriters Laboratories of Canada Inc. MH27131 - An anaerobic material which contains a lubricant and sets to form a tight seal and maintain a controlled locking strength. For use in joining threaded pipe connections or other closely fitting metal parts in devices handling natural gas and methane, gasoline and petroleum oils, and propane and butane at pressures not exceeding 13,790 kPa. Ignition temperature greater than 460 °C. Classed less than 10 below paraffin oil with respect to fire hazard. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification. NSF International Certified to ANSI/NSF Standard 61 for use in commercial and residential potable water systems not exceeding 82° C. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification. Approved by the Australian Gas Association Certificate number 3207 Class III rated working pressure 2000 kPa, working temperature -10 to 205°C. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification. TYPICAL PROPERTIES OF UNCURED MATERIAL Specific Gravity @ 25 °C 1.1 Flash Point - See SDS Viscosity, Brookfield - RVF, 25 °C, mPa·s (cP): Spindle 7, speed 2 rpm 280,000 to 800,000LMS TYPICAL CURING PERFORMANCE Cure Speed vs. Substrate The rate of cure will depend on the substrate used. The graph below shows the breakaway strength developed with time on M10 black oxide bolts and steel nuts compared to different materials and tested according to ISO 10964. 
Request
Callback


Additional Information:

  • Delivery Time: WITHIN 2 DAYS
Yes! I am Interested
View PDF

LOCTITE 577 THREAD SEALANT

LOCTITE 577 THREAD SEALANT
  • LOCTITE 577 THREAD SEALANT
Get Best Quote
Approx. Price: Rs 459 / NOGet Latest Price

Product Details:

Minimum Order Quantity5 NO
Grade StandardIndustrial Grade
BrandLOCTITE
Packaging Size50
Usage/ApplicationCeramic
Packaging TypeBOTTLE
Typesealant
Capacity200 kpa
StrengthMedium
Temperature Rangeworking -10 to 135
Coloryellow
Pressure2000 kpa
Materialpaste
Maximum Thread SizeR3"
Temperature Resistance-65 to 135
Maximum Pressure Resistance10000 psi

Agency Approvals / SpecificationsDVGW, NSF, WRAS
ColorYellow
Key CharacteristicsThixotropic
Pressure Resistance10000 psi
Temperature Max150
Temperature Min-65
Temperature Unit°C
Thread Size (Maximum)R3”
Viscosity Max130000
Viscosity Min70000
Viscosity Temperature77 °F
Viscosity UnitmPa.s (cP) Brookfield
Request
Callback


Additional Information:

  • Delivery Time: within 2 days
Yes! I am Interested
View PDF

LOCTITE 542 THREAD SEALANT

LOCTITE 542 THREAD SEALANT
  • LOCTITE 542 THREAD SEALANT
Get Best Quote
Approx. Price: Rs 508 / NOSGet Latest Price

Product Details:

Minimum Order Quantity10 NOS
Grade StandardIndustrial Grade
Surface Of ApplicationPlastic
BrandLOCTITE
Packaging Size50 ML
Usage/ApplicationINDUSTRIAL
Shelf Life1 YEAR
Packaging TypeBOTTLE
ViscosityLow
TypeThread Sealant
StrengthMedium
Temperature Range250 c
Storage Temperature8 c to 21 c
ColorBrown
Materialliquid
Torque RangeM10 steel nuts and bolts N m 15 lb in 130
Size50 ml & 250 ml
Maximum Thread Sizem 10
Temperature Resistance250 C

Thread Sealant - medium strength. For fine threads in hydraulic, pneumatic and general fittings. Fast curing.

LOCTITE® 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part.
  • Ideal for fine threads as used in hydraulic, pneumatic & general fittings
  • Suitable for metal threads only
  • Instant low-pressure seal
  • Resistant to fuel, oil, coolants and hydraulic fluids
  • Locks connection against vibration loosening
  • DVGW approval (EN 751-1): NG-5146AR0855
Technical Information
Agency Approvals / SpecificationsDVGW, WRAS
ColorBrown
Request
Callback


Additional Information:

  • Delivery Time: within 2 days
Yes! I am Interested
View PDF

Fasto A742 Thread Sealing Adhesive

Fasto A742 Thread Sealing Adhesive
  • Fasto A742 Thread Sealing Adhesive
Get Best Quote
Approx. Price: Rs 349 / PieceGet Latest Price

Product Details:

Grade StandardIndustrial Grade
Surface of ApplicationPlastic
BrandFasto
FeaturesMoisture Resistant
Packaging Size50 ml also available in 250 ml

Being a foremost organization in this industry, we are actively engaged in offering the finest quality range of Fasto A742 Thread Sealing Adhesive.


Price:

Pack sizePriceGst Extra
250 ml162218%
Request
Callback


Additional Information:

  • Item Code: Fasto-A742
Yes! I am Interested

Fasto A777 Thread Sealing Adhesive

Fasto A777 Thread Sealing Adhesive
  • Fasto A777 Thread Sealing Adhesive
Get Best Quote
Approx. Price: Rs 333 / PieceGet Latest Price

Product Details:

Grade StandardIndustrial Grade
Surface of ApplicationPlastic
BrandFasto
FeaturesImpact Resistant
Packaging Size50 ml also available in 250 ml

In order to cater to the numerous necessities of the patrons, we have been able to provide a qualitative range of Fasto A777 Thread Sealing Adhesive.

Request
Callback


Additional Information:

  • Item Code: Fasto-A777
Yes! I am Interested

Fasto A765 Thread Sealing Adhesive

Fasto A765 Thread Sealing Adhesive
  • Fasto A765 Thread Sealing Adhesive
Get Best Quote
Approx. Price: Rs 534 / PieceGet Latest Price

Product Details:

Grade StandardIndustrial Grade
Surface of ApplicationPlastic
BrandFasto
FeaturesImpact Resistant
Packaging Size50 ml also available in 250 ml

Owing to our years of industry experience and precise knowledge of this domain, we are offering an outstanding assortment of Fasto A765 Thread Sealing Adhesive.

Details:
  • Fasto A765 is Teflon based, low strength pipe sealant, enabling easier disassembly and servicing.
  • Fasto A765 is suitable for most straight and tapered pipe threads of medium to coarse pitch, from Ø15mm to Ø80mm pipe.

Features:
  • High performance
  • Low strength
  • Accurately processed
  • Effectiveness
  • Quick bonding


Price:

Pack sizePriceGst Extra
250 ml257018%
Request
Callback


Additional Information:

  • Item Code: Fasto-A765
Yes! I am Interested

Fasto A767 Thread Sealing Adhesive

Fasto A767 Thread Sealing Adhesive
  • Fasto A767 Thread Sealing Adhesive
Get Best Quote
Approx. Price: Rs 534 / PieceGet Latest Price

Product Details:

Grade StandardIndustrial Grade
Surface of ApplicationPlastic
BrandFasto
FeaturesHeat Resistant
Packaging Size50 ml also available in 250 ml

We are devoted towards offering the qualitative range of Fasto A767 Thread Sealing Adhesive, as per client’s precise need and requirements.


Price:

Pack sizePriceGst Extra
250 ml257018%

 

Request
Callback


Additional Information:

  • Item Code: Fasto-A767
Yes! I am Interested
X

Explore more products



Reach Us
Vilesh Mistry (Proprietor)
A/16, Vidya Gauri Society, Cadila Road Ghodasar.
Ahmedabad- 380050, Gujarat, India



Call Us

Share Us

F GT L


Send E-mailSend SMS