Lube Adhesive & Engineering Co.

ABOVE PRICE IS INCLUDING GST 18 %.
Air-curing dry-film lubricant Features • Excellent lubricity • Excellent corrosion protection • Air-curing • High pressure and wear resistance Composition • Solid lubricants • Organic binder • Organic solvent Applications Excellent combination of lubrication and corrosion protection. How to use Surface preparation Carefully clean and degrease surfaces to be coated with MOLYKOTE® 3402-C LF Anti-Friction Coating. Recommended pretreatments: blasting or phosphating. Both pretreatments increase the adhesion and service life of MOLYKOTE® 3402-C LF Anti-Friction Coating.How to apply Stir MOLYKOTE® 3402-C LF Anti-Friction Coating thoroughly before and during use, apply by spraying, dipping, centrifuging or brushing. Surfaces should be coated as evenly as possible. Recommended dry-film thickness: 5 to 20 µm. Coverage When applied at 10 µm dry-film thickness, MOLYKOTE® 3402-C LF Anti-Friction Coating has a coverage of approximately 12 m2/kg (this value does not take into account the losses generated during the application process). Thinner Recommended thinner is MOLYKOTE® L13 ThinnerTypical properties Specification writers: These values are not intended for use in preparing specifications. Please contact your local MOLYKOTE® sales representative prior to writing specifications on this product. Standard(1) Test Unit Result Color Gray Service temperature range °C -200 to 310 °F -328 to 590 Physical properties EN ISO DIN 2431 Viscosity, cup #4 at 23°C (73°F) s 32 ASTM D1475 Density at 23°C (73°F) g/ml 1.06 ASTM D56 Flash point °C 15 °F 59 Load-carrying capacity, wear protection, service life(2) ASTM D2625 Falex, procedure B, loadcarrying capacity N N N s=12,200 m=11,100 z=8,900 ASTM D2625 Falex, procedure A, endurance life at 4,450 N load min s=193 m=225 ASTM D2714 LFW-1, rotating, load=2,860 N @ 72 osc/min, v=7.9 m/min, no. of revolutions to µ=0.1 min s=74,800 m=108,800 ASTM D2714 LFW-1, oscillating, load=900 N @ 89.5 osc/min, no. of oscillations to µ=0.08 s=63,400 m=227,600 z=33,800 (1) ASTM: American Society for Testing and Materials. DIN: Deutsche Industrie Norm. (2) Surface pretreatmentTypical properties (continued) Specification writers: These values are not intended for use in preparing specifications. Please contact your local MOLYKOTE® sales representative prior to writing specifications on this product. Standard(1) Test Unit Result Resistance(2) ASTM B117, DIN 50021 Corrosion resistance without red rust (steel substrate, spraying application, film thickness = 10 µm)(3) h z=120 (1) ASTM: American Society for Testing and Materials. DIN: Deutsche Industrie Norm. (2) Surface pretreatment: s=sandblasted; m=Mn-phosphated; z=Zn- phosphated. (3) As the performance in corrosion protection is affected by the geometry of the parts, by the pretreatment of the surface, by the application method and by the thickness of the applied dry film, DuPont recommends customers run trials on original parts before setting specifications.

ABOVE PRICE IS INCLUDING GST 18%.
Solid lubricating paste with particularly low friction coefficient for assembly and running-in of metallic components.Features & benefits • Low friction coefficient • High pressure-absorption capacity • Prevents seizure and scoring • Suppresses stick-slip • Reduces formation of fretting corrosion • Facilitates disassembly • Good coverage • Provides emergency running performance • No intentional polytetrafluoroethylene (PTFE) or per- and polyfluoroalkyl substances (PFAS)Composition • Mineral oil • Solid lubricants Applications Suitable for the press-fit production of all types of machine elements, as a running-in lubricant for new machines and gears, as permanent lubrication of machine elements that are submitted to slight or intermittent movement only, as well as for drilling, sawing and thread-cutting. Used to lubricate threaded spindles, splined shafts, tooth gearing, worm gearing, moving screws, fittings, pumps, guides on machine tools, as well as for fitting ball and roller bearings, pulleys, wheel flanges and bolts. How to use Clean the sliding surfaces or contact areas, then apply paste with a brush, cloth, synthetic sponge or window leather. Do not use in excess as with grease lubrication. Vigorous rubbing into metal surface will improve adhesion. Do not mix with greases or oils.To enable this product to be applied more quickly and cleanly to larger areas, it is advisable to use the spray can. If using the spray, MOLYKOTE® G-Rapid Plus Paste Spray should be applied in a sweeping motion to obtain a thin, uniform coating. Avoid over application.Typical properties Specification writers: These values are not intended for use in preparing specifications. Please contact your local MOLYKOTE® sales representative prior to writing specifications on this product. Standard(1) Test Unit Result Color Black Consistency, density Unworked penetration mm/10 255-275 Density at 20°C (68°F) g/ml 1.40 Temperature Service temperature °C -35 to +450 °F -31 to +842 Load-carrying capacity Four-ball tester DIN 51 350 pt.4 Weld load N 5,300 Almen-Wieland machine OK load N > 20,000 Coefficient of friction In bolted connection M12, 8.8 with blackened surface (Erichsen tester) µ thread 0.10 µ head 0.06 Press-fit test µ 0.05, no chatteResistance DIN 51 807 pt.1 Water resistance, static, evaluation 1-90 (1)DIN: Deutsche Industrie Norm.

Features & benefits • Compatible with most rubber and plastics • Excellent stability at high temperatures • Superior resistance to chemicals and solvents • Minimal deterioration due to oxidation; appropriate for longterm lubrication • Low vapor pressure (base oil)Composition • Perfluoropolyether • Fluorinated polymer • Corrosion inhibitor Applications MOLYKOTE® HP-870 Grease can be used broadly under harsh conditions such as high temperatures, corrosive, solvent, liquefied natural gasses, high vacuum, etc. This grease is ideal for use in cleanrooms, semiconductor manufacturing equipment, cardboard manufacturing equipment, hot air dryer motor axles, etc., where the evaporation of the lubricant could be problematic.How to use Clean points of contact. As is usual with lubricating greases, apply or fill by means of a brush, spatula, or automatic lubrication device. Handling precautions PRODUCT SAFETY INFORMATION REQUIRED FOR SAFE USE IS NOT INCLUDED IN THIS DOCUMENT. BEFORE HANDLING, READ SAFETY DATA SHEETS AND CONTAINER LABELS FOR SAFE USE, PHYSICAL AND HEALTH HAZARD INFORMATION. Usable life and storage When stored, unopened, in a cool, dark place, this product has a usable life of 36 months from the date of production.Typical properties Specification writers: These values are not intended for use in preparing specifications. Please contact your local MOLYKOTE® sales representative prior to writing specifications on this product. Standard(1) Test Unit Result Appearance White JIS K 2220 Penetration (worked 60 times) mm/10 280 Service temperature range ºC -20 to 250 NLGI class 2 Density g/cm3 2.0 MIL-S-8660 Bleed (200ºC, 24 hours) % 5.0 MIL-S-8660 Evaporation (200ºC, 24 hours) % 1.0 MIL-S-8660 Evaporation (200ºC, 1,000 hours) % 3.0 ASTM D2596 Four ball weld load (1,500 rpm/1 minute) N >4,900 ASTM D2266 Four ball wear scar (1,200 rpm, 392 N, 1 hour) mm 1.3 JIS K 2220 Low temperature torque test (-20ºC) Starting torque Ncm 54 Running torque Ncm 28